Abstract:Friction is one of the main phenomena accompanying sheet metal forming methods, affecting the surface quality of products and the formability of the sheet metal. The most basic and cheapest way to reduce friction is to use lubricants, which should ensure the highest lubrication efficiency and at the same time be environmentally friendly. Due to the trend towards sustainable production, vegetable oils have been used in research as an alternative to petroleum-based lubricants. The analysis of friction in sheet metal forming requires an appropriate tribotester simulating the friction conditions in a specific area of the sheet metal being formed. Research has used a special strip drawing tribometer, enabling the determination the value of the coefficient of friction in the blankholder zone in the deep drawing process. Quantitative analysis of the friction phenomenon is necessary at the stage of designing the technological process and selecting technological parameters, including blankholder pressure. This article presents the results of friction testing of 1.0338 (DC04) steel sheets using a strip drawing test. The experimental tests involved pulling a strip of sheet metal between two countersamples with a rounded surface. The tests were carried out on countersamples with different levels of roughness for the range of contact pressures occurring in the blankholder zone in the deep drawing process (1.7–5 MPa). The values of the coefficient of friction determined under dry friction conditions were compared with the results for edible (corn, sunflower and rapeseed) and non-edible (Moringa, Karanja) vegetable lubricants. The tested oils are the most commonly used vegetable-based biolubricants in metal forming operations. Multi-layer artificial neural networks were used to determine the relationship between the value of the contact pressure, the roughness of the countersamples, the oil viscosity and density, and the value of the coefficient of friction. Rapeseed oil provided the best lubrication efficiency during friction testing for all of the tested samples, with an average surface roughness of Sa 0.44–1.34 μm. At the same time, as the roughness of the countersamples increased, a decrease in lubrication efficiency was observed. The lowest root mean squared error value was observed for the MLP-4-8-1 network trained with the quasi-Newton algorithm. Most of the analysed networks with different architectures trained using the various algorithms showed that the kinematic viscosity of the oil was the most important aspect in assessing the friction of the sheets tested. The influence of kinematic viscosity on the value of the coefficient of friction is strongly dependent on the surface roughness of the countersamples.

Predicting friction coefficient of textured 45# steel based on machine learning and analytical calculation

Machine Learning-Driven Optimization of Micro-Textured Surfaces for Enhanced Tribological Performance: A Comparative Analysis of Predictive Models

The design method for surface texture of sliding friction pairs based on machine learning under mixed lubrication

Modelling and parameter identification of coefficient of friction for deep-drawing quality steel sheets using the CatBoost machine learning algorithm and neural networks

Integration of machine learning prediction and optimization for determination of the coefficient of friction of textured UHMWPE surfaces

Prediction of frictional behaviour through regression equations: A statistical modelling approach validated with machine learning

Prediction of the tribological properties of a polymer surface in a wide temperature range using machine learning algorithm based on friction noise

Study on Friction Characteristics of Sliding Interface of Feed System

Predicting the coefficient of friction in a sliding contact by applying machine learning to acoustic emission data

Modeling and prediction of tribological properties of copper/aluminum-graphite self-lubricating composites using machine learning algorithms

Prediction of coefficient of friction of solid powder lubricants under high pressure conditions using machine learning algorithmsVorhersage des Reibungskoeffizienten von Festpulverschmierstoffen unter Hochdruckbedingungen mit Hilfe von Algorithmen des maschinellen Lernens

A Study of Tribological Performance Prediction Based on Surface Texture Parameters

Prediction of friction coefficient of su-8 and its composite coatings using machine learning techniques

Novel Online Prediction Model for Thermal Convexity of Work Rolls During Hot Steel Rolling Based on Machine Learning Algorithms

Triboinformatic modeling of dry friction and wear of aluminum base alloys using machine learning algorithms

The Comparison of the Multi-Layer Artificial Neural Network Training Methods in Terms of the Predictive Quality of the Coefficient of Friction of 1.0338 (DC04) Steel Sheet

Using Machine Learning Radial Basis Function (RBF) Method for Predicting Lubricated Friction on Textured and Porous Surfaces

Analysis of the friction performance of deep-drawing steel sheets using network models

Effects of Self-Lubricant Coating and Motion on Reduction of Friction and Wear of Mild Steel and Data Analysis from Machine Learning Approach

Integrating Friction Noise for In-Situ Monitoring of Polymer Wear Performance: A Machine Learning Approach in Tribology