Abstract:The frost of the evaporator can greatly affect the performance of the air source heat pump. When humid air comes in contact with a cold surface maintained below the freezing temperature, a frost layer begins to grow. This paper experimentally studied the frosting process of a folded-louvered-fin, parallel flow evaporator in a heat pump central air-conditioning system under three conditions, in which three different diameter capillaries were used. The surface temperature distribution of the evaporator was measured by sixteen thermocouples which buried on the leeward side and mesoscale frost formation processes on its partial surface for three different test conditions were observed using a CCD camera. The experimental result showed that the surface temperature distribution of the parallel flow evaporator was non-uniform and frost formation generally began on some partial surface of the louvered fins where the surface temperature was lowest after the heat pump system had starting up for six minutes under condition B and C, while the fins began to frost after eight minutes under condition A. The non-uniform surface temperature distribution which was caused by the unequal distribution of the refrigerant flux in the microchannels of flat tubes led to uneven distribution of frost, furthermore, incomplete evaporation of refrigerant in some tubes may be a critical factor of folded-louvered-fins’ easily frost under relative high environmental temperature condition. The ice crystals distributions and frost thickness in frost period can be obtained by the digital image processing method in which the initial pictures can be converted into binary image. The results showed that in a thin layer near to fins’ surface, ice crystals were comparable high dense in the frost growing and full grown period of frost layer; the ice crystals rate was reduced in approximate linear curves with the increasing of the frost thickness (frost height), where the decreasing rate in the frost full grown period was slower than that in the frost growing period (In 0.1 mm frost thickness, the ice crystals rate had decreased to 58% in the frost growing period, while in the frost full grown period the ice crystals rate was 90%; and in 0.25 mm frost thickness, the ice crystals rate were 0%, 45% respectively.). It also can be found that the frost thickness increased as the time increasing and then finally reached 0.3mm, 0.35 mm, and 0.32mm respectively at three conditions. The frost thickness had reached 0.1mm, 0.05mm under condition B and C respectively in 6 minutes, however, concerning condition A, the frost began to grow after 8 minutes and frost thickness arrived only 0.05mm in 14 minutes.

Machine learning based frost thickness prediction of carbon fiber-reinforced polymer composite fin for potential heat pump application

An Experimental Study on the Air Side Heat Transfer Performance of the Perforated Fin-Tube Heat Exchangers under the Frosting Conditions

Frosting Weight and Refrigerating Capacity Prediction of Fin Evaporator Based on Random Finite Element Method and Ridgelet Neural Network

A modeling study of spatial and temporal frost growth on the edge of windward fins for a tube-finned heat exchanger

Application of Smart Models for Prediction of the Frost Layer Thickness on Vertical Cryogenic Surfaces under Natural Convection

Investigation of the Frost Growth on a Parallel Flow Evaporator

A Hybrid ARIMA-SVM Model on Predicting Finned Tube Evaporator Performance under Frosting Conditions

Analysis on frosting of heat exchanger and numerical simulation of heat transfer characteristics using BP neural network learning algorithm

Machine learning-based prediction of transient latent heat thermal storage in finned enclosures using group method of data handling approach: A numerical simulation

Experimental investigation and validation on an air-source heat pump frosting state recognition method based on fan current fluctuation signal and machine learning

Modeling and Experimental Investigation on Comprehensive Performance of Perforated Wavy Fins for Heat Pump Type Air Conditioners at Frosting and Non-Frosting Conditions

Temporal and spatial frost growth prediction of a tube-finned heat exchanger considering frost distribution characteristics

Prediction of Progressive Frost Damage Development of Concrete Using Machine-Learning Algorithms

Numerical Prediction of Frosting Growth Characteristics of Microchannel Louvered Fin Heat Exchanger

Robust Predictive Models for Estimating Frost Deposition on Horizontal and Parallel Surfaces

Experimental Study of Frost Formation on Cold Surfaces with Various Fin Layouts

Pre-research on Enhanced Heat Transfer Method for Special Vehicles at High Altitude Based on Machine Learning

Machine learning approach to predict heat transfer and fluid flow characteristics of integrated pin fin-metal foam heat sink

Modeling the Airside Dynamic Behavior of a Heat Exchanger under Frosting Conditions

Frost prediction based on a 3D CFD model of heat and mass transfer in a counter-cross-flow parallel-plate liquid-to-air membrane energy exchanger

Innovative Prediction Models for the Frost Durability of Recycled Aggregate Concrete Using Soft Computing Methods