Abstract:An 1.5 GHz, 13.5 KW CW high-power magnetron for a superconducting RF accelerator has been developed by Andesun Technology Group Co., Ltd. with Nanjing Sanle Electronic Information Industry Group Co., Ltd., in order to replace the klystron, that could reduce the power source cost to about one-third. The cavity, output power antenna and coupling door-nob have been optimized by using CST Studio. Testing results have shown that the resonance frequency and output power have met the requirements, and the efficiency of the magnetron is higher that 78.45%. INTRODUCTION At present, the microwave energy of the RF superconducting accelerator is mainly provided by the klystron internationally. However, the klystron as a microwave source is characterized by low efficiency and high cost, which increases operating costs of the entire accelerator system. So the magnetron with a cost of onethird of the klystron is the best choice for the replacement of the original SRF accelerator microwave source. In order to meet the urgent need of microwave sources for SRF accelerator, a 1.5 GHz、13.5 kW CW magnetron for SRF accelerator is researched and developed by Andesun Technology Group Co., Ltd. with Nanjing Sanle Electronic Information Industry Group Co., Ltd. The development of this magnetron is based on the 2450 MHz magnetron. First, the frequency of magnetron is reduced from 2450 MHz to 1500 MHz by increasing the radius of the cavity and so on. The CST Studio is used to optimize the coupling output part of the magnetron and gets the best parameter of the coupled antenna [1]. The electronic simulation of the magnetron is completed by the Particle-in-cell solver, which gains a general understanding of the performance of the magnetron [2]. The prototype measurement shows that the output power of the magnetron reached the requirement, the whole tube efficiency is 78.45%, and the tuning range is 10 MHz. DESIGN OF THE MAGNETRON According to the working parameters of the SRF accelerator, the performance parameters of this magnetron are as follows: (1) Working frequency: 1.5 GHz (2) Average output power: 13.5 kW (3) Peak power: 17 kW (4) Efficiency: ≥70% (5) VSWR: <1.4 (6) Way of working: CW Cavity Design The anode cavity of the magnetron adopts a fan-slot type co-cavity resonance system with a diaphragm belt. A total of 10 cavities were used and the blade-to-slot ratio is 3.01. Figure 1 shows the simulation model and the electric field distribution of the π mode which is the magnetron operating mode. Cavity simulation with strips gains that the mode separation is 84.6%.

A Novel Cold Cathode Design for S-Band Continuous-Wave Magnetron

3d Particle-In-Cell Simulation Of S Band High Power Continuous Wave Magnetron

Research on a magnetron injection electron gun based on carbon nanotube cold cathode

High Current Density Nanofilament Cathodes for Microwave Amplifiers

First Demonstration and Performance of X-Band High-Power Magnetron With Parallel Cathodes

Investigation on Thermal Efficiency Enhancement and Sideband Emission Suppression for Magnetron Injection Gun

A cathode support structure for use in a magnetron oscillator experiment

Carbon Nanotube Cathodes As Electron Sources for Microwave Amplifiers

Design and Experiment of a Compact Magnetron Injection Gun for a Coil Magnet $\textit{X}$-Band Gyro-TWT

A Carbon Nanotube Cold Cathode Microwave Electron Gun

Novel cold cathode materials and applications

Efficient Relativistic Magnetron With a Split Cathode

Development of a 1497-Mhz, 13.5-Kw Continuous- Wave Magnetron for Superconducting Radio Frequency Accelerator

Electrostatic Field Simulation of Variable Pitch Helical Cathode

Preliminary Experimental Research on Split-Cathode-Fed Relativistic Magnetron With Bidirectional Emission Structure

3d Particle-In-Cell Simulation Of Continuous Wave Magnetron

Study of Pulsed Field Emission Characteristics and Simulation Models of Carbon Nanotube Cold Cathodes

Theoretical Research on a TWT Based on Magnetic Injection CNT Cold Cathode Electron Gun

Investigation on a high-power V-band transit-time oscillator under a low guiding magnetic field with a focusing cathode

Theoretical Research on A Multibeam-Modulated Electron Gun Based on Carbon Nanotube Cold Cathodes

Development of a 1.5 GHz High-power CW Magnetron for SRF Accelerator