Abstract:The pH of a system is a critical descriptor of its chemistry-impacting reaction rates, solubility, chemical speciation, and homeostasis. As a result, pH is one of the most commonly measured parameters in food safety, clinical, and environmental laboratories. Glass pH probes are the gold standard for pH measurements but suffer drawbacks including frequent recalibration, wet storage of the glass membrane, difficulty in miniaturization, and interferences from alkali metals. In this work, we describe a voltammetric pH sensor that uses a three-dimensional (3D)-printed graphene/poly(lactic acid) filament electrode that is pretreated to introduce quinone functional groups to the graphene surface. After thoroughly characterizing the pretreatment parameters using outer-sphere and inner-sphere redox couples, we measured pH by reducing the surface-bound quinones, which undergo a pH-dependent 2e-/2H+ reduction. The position of the redox peak was found to shift -60 ± 2 mV pH-1 at 25 °C, which is in excellent agreement with the theoretical value predicted by the Nernst Equation (-59.2 mV pH-1). Importantly, the sensors did not require the removal of dissolved oxygen prior to successful pH measurements. We investigated the impact of common interfering species (Pb2+ and Cu2+) and found that there was no impact on the measured pH. We subsequently challenged the sensors to measure the pH of unadulterated complex samples, including cola, vinegar, an antacid tablet slurry, serum, and urine, and obtained excellent agreement compared to a glass pH electrode. In addition to the positive analytical characteristics, the sensors are extremely cheap and easy to fabricate, making them highly accessible to a wide range of researchers. These results pave the way for customizable pH sensors that can be fabricated in (nearly) any geometry for targeted applications using 3D printing.

Low cost passive pH sensor fabricated on scotch tape

All-Solid-State Carbonate-Selective Electrode Based on Screen-Printed Carbon Paste Electrode

Pencil-on-Paper Sensor for Water Detection

Au thin-film electrodes based potentiometric CO2 sensor using Li3PO4 as both the reference material and the solid electrolyte

Online Ph Monitoring Based On A Wireless Electrodeless Quartz Crystal Microbalance With Dissipation

Open-Source Low-Cost Wireless Potentiometric Instrument for Ph Determination Experiments

Low-Cost Optical pH Sensor with a Polyaniline (PANI)-Sensitive Layer Based on Commercial Off-the-Shelf (COTS) Components

Pencil-E: Crafting Functional Electronics Using Pencils and Paper.

Fabrication of a needle-type pH sensor by selective electrodeposition

Voltammetric pH Measurements in Unadulterated Foodstuffs, Urine, and Serum with 3D-Printed Graphene/Poly(Lactic Acid) Electrodes

Development of Tungsten Oxide Nanoparticle Modified Carbon Fibre Cloth as Flexible pH Sensor

A Powerless, Gas-Permeable, Flexible and Transparent Carbon Micromesh Electrode for Simultaneous Ascorbic Acid Detection and Ph Monitoring

Flexible Graphite-on-Paper Piezoresistive Sensors

Low-Cost pH Sensors Based on Low-Voltage Oxide-Based Electric-Double-Layer Thin Film Transistors

Low-cost electrochemical biosensor based on a multi-walled carbon nanotube-doped molecularly imprinted polymer for uric acid detection

Fully Printed pH Sensor based on Polyaniline/Graphite Nanocomposites

Simple graphene chemiresistors as pH sensors: fabrication and characterization

A Paper-Based Flexible Tactile Sensor Array for Low-Cost Wearable Human Health Monitoring

Development of Miniaturized Microneedle Potentiometric Sensors for Real-Time Label-Free pH Detection Using AgIO3/Ag/PTFE/WO3/W

Highly Sensitive Potentiometric pH Sensor Based on Polyaniline Modified Carbon Fiber Cloth for Food and Pharmaceutical Applications

An all-solid-state screen-printed carbon paste reference electrode based on poly(3,4-ethylenedioxythiophene) as solid contact transducer