Abstract:High cost of custom-made conventional turbines and the lack of local manufacturing facilities have created significant obstacles to the development of Pico/micro hydroelectric schemes in the country. In this context it has been identified pump as turbine (PAT) electric schemes can have distinct advantages over conventional turbines because pumps are manufactured locally at mass scale and available in various sizes. But not all pumps are suitable for use as PAT because they have different design details and manufacturing qualities. The performance of a pump used as a turbine is assessed based on two primary parameters: turbine mode head and flow at the Best Efficiency Point (BEP). There are various methods available in the literature for predicting PAT theoretical head and flow at BEP. These methods aim to estimate how the pump will perform when used as a turbine. Despite these prediction methods, there is a consistent deviation of approximately ±20% between the theoretical estimates and the actual measured performance. This indicates that real-world conditions and factors not accounted for in theoretical models can significantly affect the performance of PAT systems. The primary objective of the present study was to measure the deviation between the actual performance and the predicted performance of two PAT systems in terms of head and flow at BEP. This deviation was then compared to the commonly mentioned figure of ±20% in the literature. The study focused on using what it considered to be the most accurate prediction method among those presented in the literature to estimate PAT head and flow at BEP and involved running reverse, 1.1 kW, and 1.6 kW direct-drive standard centrifugal type water pumps in a test rig to measure the actual performance of the two PATs. The results of the study showed a deviation of +27% and -22% between the actual measured head and flow at BEP, and the values predicted by the theoretical method. This deviation is slightly outside the commonly mentioned range of ±20% found in the literature, but this is not expected to have a detrimental effect on the generation of electric power. This implies that, even with the observed slight deviation, the prediction method used in this study can be satisfactorily employed to estimate PAT head and flow at BEP.

Investigating the Impact of Back Cavity Filling and Axial Clearance on the Flow Physics and Performance of a Pump as Turbine

Experimental and numerical investigations on pressure pulsation in a pump mode operation of a pump as turbine

CFD Simulation and PIV Measurement of the Flow Field Generated by Modified Pitched Blade Turbine Impellers

Improvement of Internal Flow Performance of a Centrifugal Pump-As-Turbine (PAT) by Impeller Geometric Optimization

The pump as a turbine: A review on performance prediction, performance improvement, and economic analysis

Study on the Impact of Blades Wrap Angle on the Performance of Pumps As Turbines Used in Water Supply System of High-Rise Buildings

Enhancing Pump as Turbine (PAT) performances: A numerical investigation into the impact of impeller leading edge rounding

Effect of blade curve shape on the hydraulic performance and pressure pulsation of a pump as turbine

A Numerical Analysis of the Effect of Impeller Rounding on Centrifugal Pump as Turbine

Investigation into Influence of Wall Roughness on the Hydraulic Characteristics of an Axial Flow Pump as Turbine

A Numerical Investigation into the PAT Hydrodynamic Response to Impeller Rotational Speed Variation

Numerical Simulation and Computational Flow Characterization Analyses of Centrifugal Pump Operating as Turbine

A Comparative Study between Theoretical and Measured Performance of Standard Centrifugal Pumps Running as Turbines

Geometrical Optimization of Pump-As-Turbine (PAT) Impellers for Enhancing Energy Efficiency with 1-D Theory

Cavitation Performance Improvement of High Specific Speed Mixed-Flow Pump

Energy performance evaluation of an axial-flow pump as turbine under conventional and reverse operating modes based on an energy loss intensity model

Numerical and Experimental Investigations on Inflow Loss in the Energy Recovery Turbines with Back-Curved and Front-Curved Impeller Based on the Entropy Generation Theory

Numerical Investigation of Flow Field and Energy Loss in a Centrifugal Pump as Turbine

Performance Prediction and Geometry Optimization for Application of Pump as Turbine: A Review

Computational Analysis on Numerical Simulation of Internal Flow Physics for Pump as Turbine in Renewable Small Hydro Energy Generation

Numerical investigation of splitter blades on the performance of a forward-curved impeller used in a pump as turbine