Removal of strontium by in situ electrochemical synthesis of Zn–Al LDHs using a bidirectional pulse method

Shiming Peng,Li Jiang,Xian Yu,Xing Yang,Guangtuan Huang

DOI: https://doi.org/10.1039/d1nj03502a

IF: 3.3

2021-01-01

New Journal of Chemistry

Abstract:The Sr 2+ removal rate is 99.26%, and the energy consumption of the reaction process is 5.01 kW h m −3 .

chemistry, multidisciplinary

What problem does this paper attempt to address?

Scandia-stabilized Zirconia-Impregnated (la, Sr)MnO 3 Cathode for Tubular Solid Oxide Fuel Cells

Renzhu Liu,Guoqiang Cai,Junliang Li,Chunhua Zhao,Shaorong Wang,Tinglian Wen,Zhaoyin Wen

DOI: https://doi.org/10.1007/s10008-010-1029-5

IF: 2.747

2010-01-01

Journal of Solid State Electrochemistry

Abstract:A LSM-ScSZ composite cathode for anode-supported tubular solid oxide fuel cell (SOFC) has been successfully developed. The fabrication method is a two-step process including dip-coating LSM framework and ion-impregnating ScSZ. A preliminary examination of the single tubular cell, which consists of a Ni-YSZ anode support tube, a Ni-ScSZ anode functional layer, a ScSZ electrolyte film, and the LSM-ScSZ cathode, has been carried out, and an improved performance is obtained. The polarization resistance of the cathode side is significantly decreased by impregnating the electronic conducting phase (LSM) with the ionic conducting phase (ScSZ). And the single cell generates the maximum power density of 433 mW cm-2 at 850 ºC, being operated with humidified hydrogen.
Fast Removal of Strontium from Nitric Acid Solution Using an Acid-Resistant Silica-Based Adsorbent

Shichang Zhang,Qunying Huang,Lifeng Chen,Xiangbiao Yin,Mohammed F. Hamza,Yuezhou Wei,Shunyan Ning

DOI: https://doi.org/10.1016/j.jece.2023.110529

IF: 7.7

2023-01-01

Journal of Environmental Chemical Engineering

Abstract:To efficiently separate strontium (Sr) from simulated high level liquid waste (HLLW), a novel acid-resistant inorganic-organic hybrid adsorbent, named as HEMAP/SiO2-P, was prepared by loading 2-hydroxyethyl-2-methyl-2-propenoate phosphate (HEMAP) into styrene-divinylbenzene modified silica (SiO2-P) with vacuum impregnation method. The experimental results showed that the adsorbent exhibited good adsorption selectivity with the SFSr/metal ions over 64.2 in 3 M HNO3 simulated HLLW. In addition, the adsorption of Sr by the adsorbent was in accordance with the pseudo-second-order kinetic model and the Langmuir isotherm model, and the adsorption equilibrium was obtained within 1 min with the saturation adsorption capacity of 61.2 mg/g. The adsorption of Sr was not markedly changed with increasing temperature. Furthermore, the results of adsorption experiments, characterization analysis, extraction experiments and density functional theory (DFT) calculations revealed that two organic ligand molecules were coordinated with one Sr molecule and simultaneously involved two nitrate molecules to maintain the charge balance during the adsorption process.
Simultaneous Arsenate and Alkali Removal from Alkaline Wastewater by In-Situ Formation of Zn–Al Layered Double Hydroxide

Zilin Meng,Fengzhu Lv,Xiaowei Li,Qian Zhang,Paul K. Chu,Sridhar Komarneni,Yihe Zhang

DOI: https://doi.org/10.1016/j.micromeso.2016.02.046

IF: 5.876

2016-01-01

Microporous and Mesoporous Materials

Abstract:An effective and facile method was developed to remove As(V) and alkali simultaneously from alkaline wastewater based on the repeated in-situ formation of Zn–Al–AsO4 layered double hydroxide (ZnAl–AsO4 LDH). The removal efficiency of As(V) was almost 100% and the pH of the treated alkaline wastewater decreased from 12 to 7.47. Removal of As(V) was not affected by competitive anions such as SO42−, F−, Cl−, and NO3− due to the large binding energy between As(V) and LDH sheets as confirmed by calculations based on the Castep Module of Materials. About 96% of As(V) can be released and concentrated into a small volume of Na2CO3 solution for disposal or recovery. The LDH was then dissolved in HNO3 and the solution can be used to treat wastewater to reform Zn–Al LDH for further removal of arsenate. This process was repeated four times but after the fifth cycle, the removal efficiency went down by the loss of Al3+ to solution but the process can be repeated by replenishing the solution with Al3+. The newly developed process is eminently suited for remediation of arsenate and alkali simultaneously from alkaline wastewater.
Sr separation and purification from refractory zinc electrolytic anode slime with Pb and Sr cocrystallization by mechanochemical ball milling

Yubin Xue,Bingbing Liu,Hu Sun,Yanfang Huang,Guihong Han

DOI: https://doi.org/10.1016/j.jiec.2023.11.001

IF: 6.76

2023-11-05

Journal of Industrial and Engineering Chemistry

Abstract:Zinc electrolytic anode slime (ZEAS) contains high contents of Mn, Zn, Sr and Pb, showing a great economic value and potential threats to environment. During the formation of ZEAS, Pb and Sr in the electrolyte were simultaneously crystallization crystallized to form a mixcrystal structure, which dramatically impedes the dissolution of Sr with a small conventional Sr leaching efficiency of 26.06%. In this study, a high-efficiency leaching method of Sr from refractory ZEAS by mechanochemical ball milling-soda converting-acid leaching-purifying-carbonating was proposed. Mechanochemical ball milling enhances the leaching efficiency of Sr by destroying the Pb and Sr cocrystallization structure and greatly improved the reaction rate of the subsequent process. The leaching efficiency of Sr is increased to 83.03%. Moreover, the Sr leaching efficiency reaches 96.81% under the optimum mechanochemical ball milling, soda conversion and acid leaching conditions. In the purification process, the optimum pH value of 13.2 and the recovery of Sr is 94.57%. The comprehensive recovery rate of Sr is above 90%, and SrCO 3 product with purity above 96% was prepared. In addition, the separation and recovery mechanism of Sr was studied, and the enrichment direction of Pb, Mn, Zn, and Ca elements were also evaluated. Graphical abstract Download : Download high-res image (124KB) Download : Download full-size image

engineering, chemical,chemistry, multidisciplinary
Adsorption of Sr on electrochemical deconsolidation products of matrix graphite

Wei Zhang,Zengtong Jiao,Chi Zhang,Linfeng He,Meili Qi,Caixia Li,Suwei Cheng,Gang Xu,Xiaotong Chen,Bing Liu,Yaping Tang

DOI: https://doi.org/10.1016/j.jnucmat.2022.154211

IF: 3.555

2023-01-01

Journal of Nuclear Materials

Abstract:With the development of high-temperature gas-cooled reactor (HTGR), the disposal of its spent fuel elements will become an important factor that affects its industrialization. As one of alternative routes for head-end process of HTGR spent fuels' reprocessing, electrochemical deconsolidation method separates TRISO fuel particles from matrix graphite (MG) and produces electrochemical deconsolidation product (EDP) with larger surface area than MG and abundant functional groups. In this paper, the chemical composition and structure of EDPs obtained in HNO 3 with concentrations of 4%, 34% and 68% were studied, and the application of EDPs on strontium ions (Sr 2 + ) adsorption was investigated. The results showed that EDP-4% with more carbonyl groups on the surface possessed the largest Sr 2 + capacity of 44.8 mg/g at pH 5, while EDP-34% containing more hydroxyl and epoxy groups had the smallest capacity of 9.6 mg/g. The capacity for EDP-68% lay in the mid value of 19.5 mg/g. Density functional theory (DFT) calculations and adsorption experiments jointly evidenced that the type and amount of functional groups both significantly impacted the Sr 2 + adsorption. The proposed adsorption mechanism provides theoretical foundation to evaluate the distribution of 90 Sr during HTGR spent fuels' electrochemical deconsolidating.(c) 2022 Elsevier B.V. All rights reserved.
Efficient Sr-90 removal from highly alkaline solution by an ultrastable crystalline zirconium phosphonate

Jiarong Zhang,Long Chen,Xing Dai,Lixi Chen,Fuwan Zhai,Weifeng Yu,Shikai Guo,Lijiang Yang,Lanhua Chen,Yugang Zhang,Linwei He,Changlun Chen,Zhifang Chai,Shuao Wang

DOI: https://doi.org/10.1039/d1cc02446a

IF: 4.9

2021-01-01

Chemical Communications

Abstract:An ultrastable zirconium phosphonate framework (SZ-7) exhibits superior Sr 2+ ion-exchange properties in 1 M NaOH solution with high adsorption capacity (183 mg g −1 ) and in-depth removal performance ( K d = 3.9 × 10 5 mL g −1 ).

chemistry, multidisciplinary
A Facile, Green and Scalable Approach to Fabricate Hierarchical ZnAl-LDH for Efficient Removal of Hexavalent Chromium

Tingting Liu,Meiqi Zheng,Kaiyue Ji,Xiaomeng Xue,Jiangrong Yang,Mingfei Shao,Haohong Duan,Xianggui Kong

DOI: https://doi.org/10.1039/d3ma00140g

2023-01-01

Materials Advances

Abstract:A feasible, green and scalable approach for the synthesis of hierarchical ZnAl-LDH with well adsorption capacity to Cr( vi ).
Preparation and Performance of Strontium-doped Lanthanum Ferrite Powder Used in Solid Oxide Electrolysis Cell Composite Anode

Kong Jiangrong,Zhang Yong,Dai Xiaming,Deng Changsheng,Xu Jingming

DOI: https://doi.org/10.3969/j.issn.1008-5548.2010.02.004

2010-01-01

Abstract:A sol-gel self-propagating method was utilized to prepare strontium-doped lanthanum ferrite (LSF) powder. The LSF and yttria stabilized ZrO2 (YSZ) composite materials were fabricated and used as the anodes of solid oxide electrolysis cell (SOEC). Their various properties were also investigated. Their chemical stability and microstructure were analyzed by X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The electrochemical performances of the materials were evaluated by anodic polarization tests. TEM results showed that the particle size of the prepared LSF powder with regular shape was about 20～50 nm. SEM images of LSF-YSZ composite anodes sintered at 1 200 ℃ for 2 hours showed that the anode layer combined closely with the electrolyte and regular pores within the anodes were observed. In addition, the YSZ and LSF phases formed interconnected pore structures respectively. Finally, the electrochemical properties and thermal stabilities of the LSF-YSZ anode composites were invetigated. The results showed that the composite anodes exhibited better catalysis activity and thermal cycle endurance.
Nanostructured layered double hydroxide (NLDH) - Zn/Al-based materials: strategy to improve performance for zirconium sorption from acidic sulfate solution

Ahmed M Masoud,Amal E Mubark,Mohamed H Taha,Saber Ibrahim

DOI: https://doi.org/10.1039/d4ra03845b

2024-09-06

Abstract:Zirconium is a highly stable radionuclide commonly used in various nuclear operations. However, removing zirconium from wastewater streams is crucial to protect the environment and human health. To achieve this, a zinc and aluminum nanostructured layered double hydroxide (Zn/Al-NLDH) was prepared and investigated for effective removal of zirconium from aqueous solutions. This study examined the prepared Zn/Al-NLDH's structural and textural properties and the impact of various factors on its adsorption performance. The Langmuir isotherm and Pseudo-second order kinetic models were found to be the best fit for the adsorption process of Zr(vi). This suggests that the adsorption process is uniform, involves the formation of a monolayer, and is chemisorption in nature. The maximum uptake capacity was 117.6 mg g-1, and the process was endothermic, spontaneous, and feasible. About 96% of Zr(vi) was successfully desorbed from the loaded sorbent using 1.0 M hydrochloric acid, and the Zn/Al-NLDH sorbent remained stable for six consecutive sorption/desorption cycles. These findings emphasize the high potential of Zn/Al-NLDH to act as a remarkable sorbent for efficiently tackling water contaminants.
Comparative study of in-situ formation process of Mg-Al layered double hydroxides though two pathways to remove Cr(VI) and As(V) from wastewater

Yuan Xie,Hanhan Huang,Zihan Zhang,Yu Wang,Fanping Kong,Zequn Ma,Huiqiang Liu,Zilin Meng

DOI: https://doi.org/10.1016/j.jece.2023.111043

IF: 7.7

2023-09-21

Journal of Environmental Chemical Engineering

Abstract:The method of direct synthesis of layered double hydroxide (LDHs) in wastewater has attracted wide attention, but the formation process and removal mechanism are still unclear. In this study, two different paths of alkali solution (NaOH) dropped to salt solution (Mg 2+ /Al 3+ ) (A-S process) and salt solution dropped to alkali solution (S-A process) were proposed to directly synthesize LDHs in wastewater and remove contaminants Cr(VI)/As(V) simultaneously. In A-S process, the formation of LDHs could be divided into three stages: initial formation of amorphous Al(OH) 3 , crystal phase transformation, and the complete formation of LDHs crystal. There was a gradual incorporation of Mg into Al(OH) 3 , and the removal of Cr(VI)/As(V) significantly increased upon the formation of LDHs structure. However, in S-A process, the formation of LDHs primarily involved crystal structure optimization. The layered structure was constantly growing and optimizing, accompanied by the removal of Cr(VI)/As(V). The Competition removal experiment of Cr(VI)/As(V) indicated that As(V) preferentially possess active sites and occupied more high-energy sites analyzed by molecular simulation and site energy distribution theory. The experimental investigation of co-existing ions, pH and recycle experiment for practical performance were also examined and demonstrated a high stability and a good recyclability.

engineering, chemical, environmental
The electrochemical performance and CO2 reduction mechanism on strontium doped lanthanum ferrite fuel electrode in solid oxide electrolysis cell

Yi Yang,Yihang Li,Yunan Jiang,Minghao Zheng,Tao Hong,Xiaojun Wu,Changrong Xia

DOI: https://doi.org/10.1016/j.electacta.2018.07.187

IF: 6.6

2018-01-01

Electrochimica Acta

Abstract:Carbon dioxide reduction reaction on the fuel electrode is critical for CO2 conversion in solid oxide electrolysis cell, which is a promising technology to utilize CO2 and store electricity from intermittent renewable resources. This work presents a highly active electrocatalyst, strontium doped lanthanum ferrite (LSF), for direct CO2 reduction reaction, which is conducted in single cells with La0.9Sr0.1Ga0.8Mg0.2O3 as the electrolyte and La0.6Sr0.4Co0.2Fe0.8O3-δ as the air electrode. A current density of 0.76 A cm−2 is achieved at 800 °C and 1.5 V when pure CO2 is electrolyzed. By adding samaria-doped ceria to form composite fuel electrodes, the performance can be effectively improved. The current density increases from 0.76 to 1.06 A cm−2 while the total interfacial polarization resistance decreases from 0.26 to 0.12 Ω cm2. Furthermore, LSF exhibits high rate constant for CO2 reduction reaction, 1.04 × 10−4 cm s−1 at 700 °C. CO2 is favorable to form carbonate species on LSF surface, and the existence of carbonate species on LSF surface revealed by Raman spectra technique is further proved by DFT calculations. A proposed CO2 reduction mechanism is obtained, providing new insights into CO2 adsorption and dissociation on LSF surface.
Effects of alkali solution treatment on the electrochemical activity of the strontium doped LaMnO3-based electrode for solid oxide fuel cells

Yaoyu Ren,Jingtao Ma,Desheng Ai,Xuping Lin,Changsheng Deng

DOI: https://doi.org/10.1016/j.elecom.2012.08.017

IF: 5.443

2012-01-01

Electrochemistry Communications

Abstract:This work investigates the effects of alkali solution treatment on the electrochemical activity of the LSM/YSZ electrode for solid oxide fuel cell. The electrode treated by alkali solution exhibits an enhanced electrochemical activity, which is independent of alkali concentration and treatment time. Only surface-segregated Sr species is removed by alkali solution as verified by ICP-MS and XPS, which can be correlated to the enhancement of the electrode activity. The electrode only treated by hot water shows a different impedance behavior from that for the case of alkali solution treatment, which can be correlated to the removal of Mn species. The electrode treated by alkali solution can still be activated by cathodic polarization.
A novel electrochemical method for the removal of aluminum from ionic rare earth leachate

Dongyue Xie,Jian Li,Hui Zhang,Yaoyao Zhu,Xuxia Zhang,Kejia Liu,Yangyang Xie,Tao Qi,Zhaohui Huang

DOI: https://doi.org/10.1016/j.seppur.2024.127296

IF: 8.6

2024-04-10

Separation and Purification Technology

Abstract:The separation of aluminum (Al) from ionic rare earth (RE) leachate is a complex challenge due to their similar chemical properties. Conventional industrial separation process required the use of chemical precipitant leads to considerable loss of RE. Herein, a novel cleaner approach of anionic membrane electrolysis (AME) combined with cyclone electrolysis for removal Al from ionic rare earth leachate was developed. The diffusion of RE 3+ and neutralization of H + and OH – were inhibited efficiently by the anionic membrane. Cyclone mixing reduced the loss of rare earth and improved Al removal compared with mechanical mixing. Working parameters including electrode speed, temperature, pH and Al concentration of catholyte, magnesium sulfate concentration and initial pH of anolyte were investigated to explore ways for more efficient Al removal and reduction of rare earth loss. Under the optimal conditions, the removal efficiency of Al and the loss ratio of RE were 93.3 % and 1.84 % respectively. The Al removal data was fitted to the pseudo-zero order model under optimal conditions, k was 0.409 mg·L −1 ·min −1 . Loss of RE was attributed to the direct deposition on the electrode surface due to the high local pH of cathode. This work provides a new insight into the clean removal of Al impurity from actual RE leachate in magnesium sulfate system.

engineering, chemical
Efficient Separation of Strontium in Different Environments with Novel Acid-Resistant Silica-Based Ion Exchanger

Shichang Zhang,Qunying Huang,Lifeng Chen,Wei Zhang,Xiangbiao Yin,Yuezhou Wei,Shunyan Ning

DOI: https://doi.org/10.1016/j.seppur.2023.124347

IF: 8.6

2023-01-01

Separation and Purification Technology

Abstract:Radioactive strontium (90Sr) is widespreadly concerned due to its high biochemical toxicity, relatively long halflife, high fission yield and potential special applications in heat source and medical field. Herein, a novel acidresistant silica-based adsorbent Sb2O5/SiO2 was prepared by a two-step method, i.e. vacuum impregnation followed by oxidation. The adsorbent was characterized by XRD, SEM, TEM, EDS, BET, FT-IR and XPS techniques, which revealed its characterization of small particle size (75-150 & mu;m), abundant functional groups and well-crystallized structure. The experimental results revealed Sb2O5/SiO2 exhibited good adsorption selectivity for Sr in pH 9-3 M HNO3 solution, the adsorption equilibriums were obtained within 5 min in pH 6 solution and 30 min in 1 M HNO3 solution with the adsorption capacities of 160.6 mg/g and 51.8 mg/g, respectively. Moreover, it also demonstrated good application potential in medical isotope preparation area as efficient strontium-yttrium (Sr-Y) separation was achieved with the separation factor over 7769 in pH 6 solution. Furthermore, the column experiments confirmed that Sr could be effectively removed both in seawater and simulated high level liquid waste (HLLW), and the purity of Y could reach to 99.7 % in Sr-Y separation. Finally, density functional theory (DFT) calculations confirmed that the adsorption mechanism was ion exchange between Sr(II) and H+ (in Sb-OH), and the adsorption was accompanied by the transfer of charge and the decrease of adsorption energy.
Applied current on the suppression of strontium segregation in Sr2Fe1.5Mo0.5O6-δ electrode for improved oxygen evolution reaction

Hao-Yang Li,Pei-Chen Su

DOI: https://doi.org/10.1016/j.apmt.2023.101769

IF: 8.663

2023-04-01

Applied Materials Today

Abstract:Strontium surface segregation is the main issue that causes long-term performance degradation in strontium-containing electrodes for solid oxide electrolysis cells. In this research, we effectively suppress strontium segregation by applying an anodic current that drives the segregated strontium back to the perovskite lattice and mitigate electrode performance degradation. By monitoring the impedance of Sr2Fe1.5Mo0.5O6-δ (SFM) air electrode under open circuit voltage at high temperature with changing current densities over time, the degradation caused by strontium segregation is verified. The applied current successfully prevent the polarization resistance from increasing is observed. The cell with 0.8 A/cm2 of the applied current increase only 3% of polarization resistance as compared to the cell without applied current after testing at 800 ℃ for 24 h. The atomic ratio of strontium on the SFM electrode surface shows lower strontium content after undergoing applied current, which means that the strontium is indeed migrated back to perovskite lattice under the applied current and result in slower degradation of the SFM electrode.

materials science, multidisciplinary
Electrical Performance of Nanostructured Strontium-Doped Lanthanum Manganite Impregnated Onto Yttria-Stabilized Zirconia Backbone

Jiangwei Ju,Jie Lin,Yusu Wang,Yanxiang Zhang,Changrong Xia

DOI: https://doi.org/10.1016/j.jpowsour.2015.09.074

IF: 9.2

2016-01-01

Journal of Power Sources

Abstract:Strontium-doped lanthanum manganite (LSM) nanoparticles are deposited onto porous yttria-stabilized zirconia frameworks via an ion impregnation/infiltration process. The apparent conductivity of the impregnated LSM nanostructure is investigated regarding the fabricating parameters including LSM loading, heat treatment temperature, heating rate, and annealing at 750 degrees C for 400 h. Besides, the conductivity, the intrinsic conductivity as well as Bruggeman factor of the impregnated LSM is estimated from the apparent conductivity using the analytical model for the three-dimensional impregnate network. The conductivity increases with LSM loading while the interfacial polarization resistance exhibits the lowest value at an optimal loading of about 5 vol.%, which corresponds to the largest threephase boundary as predicted using the numerical infiltration methodology. At the optimal loading, the area specific ohmic resistance of the impregnated LSM is about 0.032 Omega cm(2) at 700 degrees C for a typical impregnated cathode of 30 mu M thick. It is only 5.5% of the cathode interfacial polarization resistance and 3.3% of the total resistance for a single cell consisting of a Ni-YSZ support, a 10 mu m thick electrolyte and a 30 mu m thick cathode, demonstrating that the ohmic resistance is negligible in the LSM impregnated cathode for SOFCs. (C) 2015 Elsevier B.V. All rights reserved.
Strontium Extraction Based on Macroscopic Supramolecular Assembly in Ionic Liquid System

SHI Ce,XIONG Shi-jie,SHEN Xing-hai

DOI: https://doi.org/10.7538/hhx.2022.yx.2021091

2022-01-01

Abstract:The separation of strontium is important in the recovery of radioactive resources. Ionic liquids(ILs) based extraction systems of Sr have been greatly expanded, but the separation of Sr and Cs remains a problem. In addition, the problem of radioactive waste affects the application of IL systems in the field of spent fuel reprocessing. In this work, the macroscopic supramolecular assembly(MSA) of strontium at the interface of IL extraction systems and its basic research on the extraction of Sr were reported. The MSA behavior of Sr2+ in ionic liquid based extraction systems was studied and the structure of Sr-MSA was analyzed by mass spectrometry, 13C NMR, infrared spectroscopy and theoretical calculation. Sr-MSA was formed by using CnOHmimNTf2 (n=2, 3) as the ILs and CMPO, TODGA as the extractants. The three step mechanism of MSA process is proposed: complexes formed by Sr2+ and CMPO are extracted to IL phase. The complexes and IL assemble into nanoparticles driven by non covalent interactions such as electrostatic attraction, hydrogen, hydrophobic interaction. The nanoparticles aggregate into mesoscopic assemblies. The mesoscopic assemblies move to the interface and grow further into macroscopic intermediates. The intermediates finally generate into Sr-MSA under the traction from Marangoni effect. A new method for the selective extraction and one step solidification of Sr2+ from aqueous solutions was developed. The Sr-MSA can be taken out with tweezers easily from aqueous solution. The method can still be used in high acidity environment.
A kinetic study of the strontium extraction by metallothermic reduction using submerged SrO powders injection

R. Muñiz,A. Flores,J. Torres,S. Luna,N. Rodríguez

DOI: https://doi.org/10.1016/j.matlet.2007.06.024

IF: 3

2008-02-01

Materials Letters

Abstract:This work reports the results of laboratory experiments conduced to follow the kinetics of strontium recovery into the Al–Mg alloy by metallothermic reduction of SrO. The reagent was incorporated to molten alloy by the use of submerged powders injection technique. The variables analyzed were the injection time, the melt temperature and the initial magnesium content. Magnesium is added to the melt to increase the reactivity and reduce the surface tension of the molten aluminum. It was possible to increase the strontium content from 0 to 5 wt.% after 60 min of treatment. The results were fitted to a general kinetic equation, which allowed it to obtain the kinetic parameters, i.e. order of reaction and activation energy of the process. As the main mechanism of the strontium recovery process is of diffusive type, the global process rate increases as the temperature and initial amount of the magnesium increased.

materials science, multidisciplinary,physics, applied
On the chemical interaction of nanoscale lanthanum doped strontium titanates with common scandium and yttrium stabilized electrolyte materials

Dariusz Burnat,Andre Heel,Lorenz Holzer,Eugenio Otal,Dariusz Kata,Thomas Graule

DOI: https://doi.org/10.1016/j.ijhydene.2012.09.022

IF: 7.2

2012-12-01

International Journal of Hydrogen Energy

Abstract:Chemical interactions between common electrolyte materials and various La doped strontium titanates (LST), which are redox-stable candidates for SOFCs anodes, were thoroughly investigated. The reactions of nanosized reagents were studied by SEM/EDX microscopy and XRD with subsequent Rietveld refinement. It was found that all A-site deficient LSTs promoted a reaction with Sc and Y stabilized zirconia, whilst stoichiometric LST was chemically stable. Detected structural and microstructural changes were solely assigned to high mobility of Ti. Diffusion of Ti into the zirconia structure promoted formation of tetragonal structures with p42/nmc-type space groups. The results indicate that the reduction of oxygen partial pressure during sintering and application of Sc-containing electrolyte material are successful strategies to hinder or even avoid reactivity.

energy & fuels,electrochemistry,chemistry, physical
A novel path to prepare Fe/Al-layered double hydroxide nanosheets by sacrificial double anodes for the treatment of Cr-containing wastewater

Haijun Qiu,Xu Wang,Jing Cen,Penghui Shi,Jinchen Fan,Yulin Min,Qunjie Xu

DOI: https://doi.org/10.1016/j.jcis.2019.01.084

2019-04-15

Abstract:Many methods used to synthesize efficient reducing agents of Fe and Al-layered double hydroxide (Fe/Al-LDH) nanosheets against oxidizing contaminants often require the use of unstable bivalent iron salts and long aging times at ambient temperatures. Here, we developed an easy-to-operate, environment-friendly, and scaled-up electrochemical engineering method without adding metal salts to synthesize Fe/Al-LDHs via an electrolytic reaction of active metal electrodes (Fe and Al). The process resulted in the growth of thin hexagonal Fe/Al-LDHs with a lateral size of approximately 100 nm and thickness of approximately 32 nm. The crystallization process of Fe/Al-LDHs strongly relied on the crystal nucleus of the first precipitate Al(OH)3 and the Fe chemical valence. The oxidation state of Fe was markedly influenced by hydroxyl ions that formed on the cathode surface and the oxygen evolution reaction at high current density (i). The fast and simple manufacturing technique not only had high yield (approximately 0.2 g of Fe/Al-LDHs was obtained when i was 2 mA/cm2 within 25 min) but also afforded Fe/Al-LDHs with excellent reducibility for the removal of Cr(VI). This study demonstrated an attractive option for the rapid and large-scale synthesis of Fe/Al-LDHs to enhance their application prospects.

Removal of strontium by in situ electrochemical synthesis of Zn–Al LDHs using a bidirectional pulse method

Scandia-stabilized Zirconia-Impregnated (la, Sr)MnO 3 Cathode for Tubular Solid Oxide Fuel Cells

Fast Removal of Strontium from Nitric Acid Solution Using an Acid-Resistant Silica-Based Adsorbent

Simultaneous Arsenate and Alkali Removal from Alkaline Wastewater by In-Situ Formation of Zn–Al Layered Double Hydroxide

Sr separation and purification from refractory zinc electrolytic anode slime with Pb and Sr cocrystallization by mechanochemical ball milling

Adsorption of Sr on electrochemical deconsolidation products of matrix graphite

Efficient Sr-90 removal from highly alkaline solution by an ultrastable crystalline zirconium phosphonate

A Facile, Green and Scalable Approach to Fabricate Hierarchical ZnAl-LDH for Efficient Removal of Hexavalent Chromium

Preparation and Performance of Strontium-doped Lanthanum Ferrite Powder Used in Solid Oxide Electrolysis Cell Composite Anode

Nanostructured layered double hydroxide (NLDH) - Zn/Al-based materials: strategy to improve performance for zirconium sorption from acidic sulfate solution

Comparative study of in-situ formation process of Mg-Al layered double hydroxides though two pathways to remove Cr(VI) and As(V) from wastewater

The electrochemical performance and CO2 reduction mechanism on strontium doped lanthanum ferrite fuel electrode in solid oxide electrolysis cell

Effects of alkali solution treatment on the electrochemical activity of the strontium doped LaMnO3-based electrode for solid oxide fuel cells

A novel electrochemical method for the removal of aluminum from ionic rare earth leachate

Efficient Separation of Strontium in Different Environments with Novel Acid-Resistant Silica-Based Ion Exchanger

Applied current on the suppression of strontium segregation in Sr2Fe1.5Mo0.5O6-δ electrode for improved oxygen evolution reaction

Electrical Performance of Nanostructured Strontium-Doped Lanthanum Manganite Impregnated Onto Yttria-Stabilized Zirconia Backbone

Strontium Extraction Based on Macroscopic Supramolecular Assembly in Ionic Liquid System

A kinetic study of the strontium extraction by metallothermic reduction using submerged SrO powders injection

On the chemical interaction of nanoscale lanthanum doped strontium titanates with common scandium and yttrium stabilized electrolyte materials

A novel path to prepare Fe/Al-layered double hydroxide nanosheets by sacrificial double anodes for the treatment of Cr-containing wastewater