Abstract:Environmental concerns lead to a continually growing demand for clean energy generation. Thus, alternative energy sources or green fuels attract attention. The anion exchange membrane fuel cell (AEMFC) emerged as an excellent alternative due to its air CO 2 -free emissions, low-cost electrocatalyst used at the cathode, and industrial-scale membrane production development [1-3]. Many efforts have been made to have AEMFC performances like those already shown by the proton exchange membrane fuel cell (PEMFC). Excellent results have been obtained for the lasted technology regarding power densities and operational cell life [4]. It should be recognized that due to the nature of the electrode reactions in AEMFC, Eqs. 1-2, the performance enhancement of the overall cell reaction, Eq. 3, depends not only on the selected catalysts and ionomers/membranes but also on the cell's water management. The complexity of water management relies on the simultaneous production and consumption of water in anode and cathode, respectively, where the production is two-fold higher than the consumption. This effect might lead to anode flooding during the hydrogen oxidation reaction (HRR), Eq. 1. In contrast, during oxygen reduction reaction (OER), Eq. 2, the risk of membrane drying is latent as long as a water imbalance arises between both anodic and cathodic sides. It has been confirmed quantitatively that water direction movement could go from anode to cathode in a hydrophilic membrane (diffusion transport mode); however, using a membrane with hydrophobic properties promotes the water to travel from cathode to anode (electro-osmotic drag, EOD mode). In this context, it is convenient to identify the water direction trend under variable selected operating conditions. In particular, achieving the anode-to-cathode water direction would improve the AEMFC performance by avoiding flooding on the anode by cathode hydration through water diffusion through the membrane. Therefore, this work tested the influence of symmetric and asymmetric flow rates and relative humidities within an AEMFC using a hydrophilic membrane. According to both modes of transport, the AEMFC performance was studied using polarization curves. The experimental procedure involved trapping water out of each half-cell during a chronoamperometry in steady-state conditions. Also, the water incoming was quantified independently for each selected operating condition in order to make a mass balance (Figure 1a). The variable operating conditions were the reactant flow rate, low (125 cm 3 min -1 ) and high (250 cm 3 min -1 ), and the reactant humidity level. In Figure 1b, the results demonstrated that the EOD predominance was promoted when low symmetric flow rates (125 cm 3 min -1 for anode and cathode) were used in the AEMFC, suggesting membrane dehydration. On the contrary, the water diffusion dominance appears under high (250 cm 3 min -1 ) symmetric and asymmetric flow rates between anode and cathode; under these conditions, the membrane dehydration might be suppressed by anode flooding alleviation. Once the flow conditions are given, no changes in water transport mode were detected for changes in the humidity level (Figure 1c-d). The AEMFC performance was affected by the water transport mechanism, giving lower peak power densities for EOD-dominated systems (35.2 mW cm -2 at 60°C, Figure 1e) than those obtained by diffusion (62.8 mW cm -2 at 60°C, Figure 1f). The most suitable operating condition is under water-diffusion at non-saturated streams (below 65%), where a decrease in performance is experienced as the humidifier temperature increases from 60°C to 80°C (supersaturated flow), with peak power densities of 62.8 and 3.7 mW cm -2 , respectively. References: Zhang, J. Liu, Y. Wang, L. An, M. D. Guiver, N. Li, Highly Stable Anion Exchange Membranes Based on Quaternized Polypropylene, J. Mater. Chem. A 3 (2015) 12284-12296. https://doi.org/10.1039/C5TA01420D G. Wright, F. Jiantao, B. Britton, T. Weissbach, H. F. Lee, E. A. Kitching, T. J. Peckham, S. Holdcroft, Hexamethyl-p-terphenyl poly(benzimidazolium): A Universal Hydroxide-Conducting Polymer for Energy Conversion Devices, Energy Environ. Sci. 9 (2016) 2130-2142. https://doi.org/10.1039/c6ee00656f Zhang, Y. Hua, Z. Gao, Strategies to Optimize Water Management in Anion Exchange Membrane Fuel Cells, J. Power Sources 525 (2022) 231141. https://doi.org/10.1016/j.jpowsour.2022.231141 Gottesfeld, D. R. Dekel, M. Page, C. Bae, Y. Yan, P. Zelenay, Y. S. Kim, Anion Exchange Membrane Fuel Cells: Current Status and Remaining Challenges, J. Power Sources 375 (2018) 170-184. https -Abstract Truncated-

Experimental investigation of bio-inspired flow field design for AEM and PEM water electrolyzer cells

A New Design of a Microfluidic Experimental Cell for the Study of Two-Phase Flow inside a PEM Water Electrolyzer

High Performance AEM Water Electrolysis with Aemion® Membranes

(Energy Technology Division Graduate Student Award sponsored by BioLogic) In-Situ Diagnostic Tools and Analysis to Identify Root Causes for Voltage Losses in Anion Exchange Membrane Water Electrolyzers

Spectroscopy electrochemical impedance characterization of membranes electrode assemblies for PEM electrolyzers

Multi-Dimensional Modelling of Bioinspired Flow Channels Based on Plant Leaves for PEM Electrolyser

Parametric study of PEM water electrolyzer performance

Enhancing Heat Removal and H2O Retention in Passive Air-Cooled Polymer Electrolyte Membrane Fuel Cells by Altering Flow Field Geometry

Investigation on the Microfluidics in PEM Water Electrolyzers

Experimental investigation of the effect of bioinspired flow field design on polymer electrolyte membrane fuel cell

Influence of Anode Flow-Field Channel Distance on the Performance of Polymer Electrolyte Membrane Water Electrolyzers

Investigation on performance of proton exchange membrane electrolyzer with different flow field structures

Pathways Toward Efficient and Durable Anion Exchange Membrane Water Electrolyzers Enabled By Electro‐Active Porous Transport Layers

Performance assessment and optimization of the PEM water electrolyzer by coupled response surface methodology and finite element modeling

Influence of Gas Humidity and Flow Rate on the Water Movement Direction through an Anion Exchange Membrane Fuel Cell

(Invited) Water Electrolyzers for Green Hydrogen Production - a Tutorial on Catalyst and Electrode Development for Next Generation Devices

Polymer electrolyte membrane fuel cell flow field designs and approaches for performance enhancement

A comparative numerical analysis of proton exchange membrane water electrolyzer using different flow field dynamics

Engineering potential electrocatalysts for both AEM Electrolyzers and Redox Flow Batteries: Design of experiments at the different scales

Numerical investigations on electrolytic performance of proton exchange membrane electrolysis cell with parallel flow field

Numerical Investigation on the Effects of Design Parameters and Operating Conditions on the Electrochemical Performance of Proton Exchange Membrane Water Electrolysis