Abstract:Zn–Ni, Zn–Co and Zn–Ni–Co coatings were electrodeposited on mild steel from an acidic chloride bath containing p-aminobenzenesulphonic acid (SA) and gelatin. These additives changed the phase content in the coatings, most likely as a result of their adsorption at the surface of the cathode. The effect of gelatin was more pronounced than that of SA. The Faradaic efficiency was higher than 90%. As the current density was increased or the bath temperature was decreased, the concentration of the nobler metal in the coating increased. Both concentrations of Ni and Co in the ternary alloy increased as the applied current density was increased. Nickel and cobalt were found to have a synergistic catalytic effect. The thickness of all coatings increased as the applied current density was increased. The hardness increased with current density to a peak value, and then decreased. The rate of Zn deposition was heavily influenced by mass-transport limitation at high applied current densities, while the rates of Ni and Co deposition were not. The anomalous codeposition was explained by the great difference between the exchange current densities of Zn and the iron-group metal. Potentiodynamic polarization scans and electrochemical impedance spectroscopy showed that the corrosion resistance of the ternary Zn–Ni–Co alloy coatings was approximately 10 times higher than that of Zn–Ni and 7 times higher than that of Zn–Co. The improved corrosion resistance of the ternary alloy was attributed to its surface chemistry, phase content, texture, and surface morphology. The ternary Zn–Ni–Co coating may thus replace the conventional Zn–Ni and Zn–Co coatings in a variety of applications.

Electroless coating technology for 1060 aluminum alloy and the effect of tin chloride and ‎polymer addition

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Electroplating and Physicochemical Properties of Zinc–Nickel Alloy Coatings from Ammonium Oxalate Electrolytes

Effects of Al content on microstructure and corrosion behavior of Zn-Al alloy coatings

A Method for Electroless Nickel Plating on Aluminum Alloy Surface

Mechanical and Corrosion Resistance Enhancement of Closed-Cell Aluminum Foams through Nano-Electrodeposited Composite Coatings

Effect of Mg on Al-Mg Alloy and Electroless Ni-P Codeposition of nano-Al2O3: Mechanical, Wear, and Corrosion Resistance Properties

Electroless Plating of Ni-P on Surface of C_f/Al Composites

Technology for Ni-Al2O3 Composite Coating and Its Properties

The Effect of Coating Morphology on Anti-Corrosion Behavior of Modified Alumina Coating Over Aluminum Alloy

Formation and Physicochemical Properties of Composite Electrochemical Coatings of Tin–Nickel Alloy with Silicon Dioxide Incapsulated by Nanosized Titanium Dioxide

Preparation of aluminum-tin alloy by electrodeposition in low-temperature molten salt system

Microstructure and Corrosion Behavior of Electroless Ni–P on Sprayed Al–Ce Coating of 3003 Aluminum Alloy

Corrosion Behavior of Ni-P-Nano-Al2o3 Composite Coating in the Presence of Anionic and Cationic Surfactants

The Improvement of Corrosion Resistant for the Cf/Al Composites by Ni-P Coatings

Electroplating and characterization of Zn–Ni, Zn–Co and Zn–Ni–Co alloys

Microstructure evolution and improved corrosion resistance of electrodeposited NiCo-Al composite coatings with different Al contents

Anticorrosion Protection of New Composite Coating for Cobalt-Based Alloy in Hydrochloric Acid Solution Obtained by Electrodeposition Methods

Study of Electroplating Zn-Sn-Ni Alloy

Preparation and Properties of Mo/Ti/Sn Conductivity Conversion Coatings on 6063 Aluminum Alloy

Plating Bath Composition Optimization And Corrosion Resistance Of Ni-Sn-Mn Amorphous Coating Prepared By Electrodeposition