Abstract:Currently there is a growing interest in investigating aluminum alloy-based hybrid composites due to their growing importance in the automotive and aerospace sectors. To enhance the value of this field, an attempt was made to synthesize zirconium diboride (ZrB 2 ) and copper-coated short steel fiber-reinforced LM26 aluminum alloy hybrid composites using stir casting with varying weight percentages of ZrB 2 (2.5, 5, and 10wt%) and copper-coated short steel fiber (5wt% kept constant) for applications requiring a lightweight and high strength, particularly for high-temperature applications. Matrix, fiber-reinforced composite (FRC), and hybrid composite specimens were synthesized using stir casting technique with the process parameters of 750°C for pouring temperature, 10 minutes for stirring time, 650 rpm for stirring speed, and 400°C for preheating temperature of reinforcements. With the use of a wire-cut electrical discharge machine, the specimens were prepared for various tests in accordance with ASTM standards. A complete microstructural (optical microscope and scanning electron microscope) investigation and mechanical property (hardness, tensile properties, and impact strength) evaluation were carried out according to the ASTM standard to comprehend the influence of the reinforcements, and the findings were presented. The optical microscopic images clearly showed that the ZrB 2 and copper-coated short steel fiber reinforcements were uniformly distributed throughout the matrix (LM26 aluminum alloy). The Brinell hardness values increased as the reinforcements were added, reaching a maximum hardness of 152 BHN for the hybrid composite with 15wt% cumulative reinforcement, which is 35.71% higher than the matrix. Compared to matrix alloy, the composite with 15% cumulative reinforcement exhibited a maximum 38.41% improvement in ultimate tensile strength. As further reinforcement is added after 10wt%, yield strength declines to 6.36%, and for the composite with 15wt% of reinforcement, elongation gradually drops to 33.7% as compared to the matrix. The energy absorption of reinforced composites with 5wt% and 15wt% shows a similar percentage decrease of 42.86%, when compared to the matrix. However, a notable decline in ductility was identified for the composites because of the addition of strong reinforcements, while the LM26 alloy retained its ductility. Further, hybrid composites showed poor resistance to impact load due to the incorporation of hybrid reinforcements, and respective fractography showed brittle fracture. The results make it quite evident that the hybrid composites of copper-coated short steel fiber and ZrB 2 -reinforced LM26 aluminum alloy have outstanding mechanical properties, making them a good choice for use in the automobile industry as a newer material.

Effect of Copper/Alumina Hybrid Reinforcement on the Microstructure and Mechanical Properties of Stir Cast Aluminum Alloy AA6063

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Mechanical Behaviour of Aluminium Hybrid Composites Reinforced with: Rice Husk Ash - Silicon Carbide - Copper Nanoparticles

Alloying effect of copper in AA-7075 aluminum composite using bale out furnace

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Investigation on Mechanical Behavior of Al6061- Coconut Shell Ash- Granite Dust Reinforced Hybrid Metal Matrix Composites Manufactured using Stir Casting Technique

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Investigation on Mechanical Behavior of LM26 Aluminum Alloy—ZrB2 and Copper-Coated Short Steel Fiber-Reinforced Composites Using Stir Casting Process

Influence of Vanadium and Niobium Carbide Particles on the Mechanical, Microstructural, and Physical Properties of AA6061 Aluminum-Based Mono- and Hybrid Composite Using FSP

Mechanical Properties of Aluminum-4043/Nickel-coated Silicon Carbide Composites Produced via Stir Casting

Investigation On Tensile Properties Of Aluminum 7075 - Silica Particles -Boron Fiber- Reinforced Hybrid Metal Matrix Composites

Effect of copper addition on mechanical properties and microstructures of LM25 cast alloys

Microstructural, Mechanical, and Tribological Characteristics of Ceramic Reinforced Al/Cu Hybrid Matrix Composites

Experimental Investigation and Comparative Analysis of Aluminium Hybrid Metal Matrix Composites Reinforced with Silicon Nitride, Eggshell and Magnesium

Corrigendum: A study on the effects of hybrid (SIC- PSSA) nano sized reinforcement on mechanical and tribological behaviour of Al alloy-based metal matrix composite produced by ultrasonic assisted stir casting (2024 Mater. Res. Express 11 075010)

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Enhancing the mechanical, wear and corrosion behaviour of stir casted aluminium 6061 hybrid composites through the incorporation of boron nitride and aluminium oxide particles

Effect of Cu Content on Microstructure and Properties of Al2o3-Sio2 Fiber Reinforced Aluminum Matrix Composites

Experimental investigation on the mechanical performance of the Al2O3 and ZrO2 added Al-Mg-Si alloy for structural applications

Study on Metallurgically Prepared Copper-Coated Carbon Fibers Reinforced Aluminum Matrix Composites