Abstract:Perovskite solar cells (PSCs) have emerged as a promising candidate for addressing the energy crisis due to their rapid efficiency improvement up to 24.2% within 10 years. One of the most challenging obstacles to commercialization of PSCs is their instability toward environmental conditions. Lead-free, halide-based perovskites are drawing appreciable attention for solar cell applications due to the non-toxic nature and stable performance in ambient environment. With the aim of improving reproducibility and spectral properties of the devices, in the last three years the scientific community strongly focused on Caesium-doping for hybrid (typically, organolead) perovskites. In parallel, in order to further contrast hygroscopicity and reach thermal stability, research has also been carried out to achieve the development of all-inorganic perovskites based on Caesium, the performances of which are actually rapidly increasing. This article represents the study of physical, optical, and electrical properties Caesium Titanium (IV) based single halide Perovskite absorbing material for the optimum photovoltaic application. Also in recently developed high-efficiency metal organometal halide PSCs, electron and hole transporting materials have shown key roles in determining the growth of perovskite crystals, as well as the performance and stability of the device. The utilization of polymer materials has been studied as both HTM's and ETM's but with little effectiveness, typically resulting in a lower conversion efficiency. But some other materials such as Spiro-OMeTAD requires comparable dopants and additives, which is a source of perovskite instability and also it requires very high design costs ; which all leads to the idea of alternate transport materials. In this study, a numerical simulation analysis on the PSCs performance with Graphene Oxide (GO) as HTM is conducted. We investigated GO/Cs 2 TiBr 6 / TiO 2 structure (Figure 1) and studied the change in various photovoltaic parameters with the change in different input factors. The deep understanding of operation mechanism of PSCs is essential and required to furtherly improve device performance. Therefore, Solar Cell Capacitance Simulator (SCAPS-1D), a device simulator widely using in inorganic solar cells, was employed to controllably design PSCs. This simulator package basically uses the poisons equation, the drift and diffusion carrier equation and the continuity equation to solve for various input parameters. It has numerous advantages than any other simulators available in the market like incorporating the interface defect densities, simulation of devices with up to 7 layers in a single run etc. The influence of thickness of the absorber layer, the hole transport layer, defect density of two interfaces ( perovskite/ETL and HTL/perovskite), band gap of absorber layer, electron affinity of both absorber and ETL , finally the temperature and parasitic resistance ( series and shunt ) of the lead-free device is studied. The main objective of the study was the exploration of the effect and efficiency of Graphene Oxide (GO) and the Hole transport layer (HTL) on the performance of the proposed Caesium based heterojunction solar cell. The simulation was carried out in the standard operation conditions for SCAPS-1D. The optimized thickness values for maximum PCE value are observed to be 1 μm for absorber, 0.1 μm for HTL. The performance of the device deteriorated when the defect density value increases for both interfaces and was found that that the front interface density should be less than 1E16 and the back interface density less than 1E10 for optimum performance. It can be attributed due to larger number of recombinations at these interfaces. The performance decreased with the increase in operating temperature range and also with the increase in parasitic resistances as expected. Finally the electron affinity of the absorber seems to be not much involved with the inner working of the device as the parameters almost remained constant with a change in it. The elicited results suggest that Cs 2 TiBr 6 can play a momentous role as an absorbing perovskite towards the highly efficient lead-free all-inorganic perovskite solar cell technology .The findings also reveal that the GO could be a promising HTL for the fabrication of low cost, high efficiency Caesium based heterojunction solar cell. In the future, this efficiency may offer prominent potential as a substitute in a highly efficient green solar absorber material for photovoltaic applications after confirmation in the laboratory. Figure 1

Impact of silver contacted graphene oxide as hole transport material on the performance of lead-free perovskite solar cell

Influence of layer thickness, defect density, doping concentration, interface defects, work function, working temperature and reflecting coating on lead-free perovskite solar cell

Suppression of Sn2+/Sn4+ oxidation in tin-based perovskite solar cells with graphene-tin quantum dots composites in active layer

Design and simulation of perovskite solar cell using graphene oxide as hole transport material

Efficient planar heterojunction perovskite solar cells employing graphene oxide as hole conductor.

Performance of perovskite solar cell coated with graphene oxide as hole transport layer

Enhancement of efficiency in CsSnI3 based perovskite solar cell by numerical modeling of graphene oxide as HTL and ZnMgO as ETL

Optical engineering of uniformly decorated graphene oxide nanoflakes via in situ growth of silver nanoparticles with enhanced plasmonic resonance

Multifunctional Brominated Graphene Oxide Boosted Charge Extraction for High-Efficiency and Stable All-Inorganic CsPbBr3 Perovskite Solar Cells

Impact of hole transport layer on the performance of all-inorganic tin (Sn) based perovskite solar cells

Numerical Study on the Effect of Graphene Oxide As Hole Transporting Layer in Caesium Based Perovskite Solar Cell – Scaps 1D Approach

Thermal and Power Performance Optimization of Cost-Effective Solar Cells using Eco-Friendly Perovskite Materials

Enhancing CsSn0.5Ge0.5I3 Perovskite Solar Cell Performance via Cu2O Hole Transport Layer Integration

Fabrication and Degradation Analysis of Perovskite Solar Cells with Graphene Reduced Oxide as Hole Transporting Layer

Efficient and Air-Stable Planar Perovskite Solar Cells Formed on Graphene-Oxide-Modified PEDOT:PSS Hole Transport Layer

Working from Both Sides: Composite Metallic Semitransparent Top Electrode for High Performance Perovskite Solar Cells

Investigation of excellent transparent conducting electrode for efficient organometallic halide perovskite solar cell

Analysis of eco-friendly tin-halide Cs2SnI6-based perovskite solar cell with all-inorganic charge selective layers

Charge transfer doping of graphene oxide with nickel oxide nanoparticles for stable and efficient carbon-based, all-inorganic CsPbBr3 perovskite solar cells

Highly Efficient Inverted Perovskite Solar Cells Based on Self-Assembled Graphene Derivatives

Numerical simulation and optimization of lead free CH3NH3SnI3 perovskite solar cell with CuSbS2 as HTL using SCAPS 1D