Abstract:Surface Review and Letters, Ahead of Print. The removal of metal in the form of sludge can be termed an ECM process, having primary salient features consisting of the tool, workpiece, power supply and electrolyte solution. ECM is a potential nontraditional machining process that includes too many factors contributing to process performance. Therefore, obtaining optimal factor combinations for higher efficiency is complex. In this research work, machining parameters are voltage, powder concentration and electrolyte concentration, based on which material removal rate (MRR) and surface roughness (SR) are derived. Regression analysis, signal-to-noise ratios and analysis of variance (ANOVA) are performed to determine the optimal levels and to examine the effects of machining parameters on MRR and SR. The results derived from the experiments noticed that the MRR decreases when the voltage level is increased and surface roughness decreases for the applied voltage. In case of an increase in powder concentration, MRR decreases from range 4 to 6 and further reduces to 6–8. In case of SR, it additionally decreases on the maximum level of powder concentration. In electrolyte concentration, the MRR decreases on the increment of electrolyte and increases after a short period of time; simultaneously SR is increased from range value 10–20 and decreased with a maximum level 20–30 of NaCl solution. A comparison of MOORA-PCA and TOPSIS-PCA demonstrates the superiority of TOPSIS over MOORA technique. Statistical results (95% confidence level) indicate that the voltage, powder concentration, and electrolyte concentration affect the surface roughness by 69.50%, 8.67% and 14.59% in the electrochemical machining of d3 die steel. Therefore, the optimum combination of process parameters corresponding to voltage: 45[math]V, powder concentration: 4[math]g/L, and electrolyte concentration: 10 NaCl/L, respectively, were found to yield the desired result. The prediction accuracy of the TOPSIS-PCA hybrid approach model is found better than MOORA-PCA technique.

Experimental investigations and optimization of process variables of electro discharge coating process for Al-7075 alloy: a hybrid MCDM approach

Parametric study on surface modification of Al-7075 alloy using electric discharge coating

Process parameters optimization of EDM for hybrid aluminum MMC using hybrid optimization technique

Investigation on Electrical Discharge Machining Parameters of Aluminium7075/Boron Carbide/Titanium Diboride Hybrid Composites by Grey Relational Analysis

A Hybrid Design of Experiment Approach in Analyzing the Electrical Discharge Machining Influence on Stir Cast Al7075/B4C Metal Matrix Composites

Electrical discharge machining process investigation and optimization of parameters for machining of aluminum silicon dioxide (Al7075–SiO2) composite

Experimental analysis of surface integrity in electro-discharge coating process

Statistical analysis of process parameters and multi-objective optimization in wire electrical discharge machining of Al 7075 using weight-based constrained algorithm

Enhancing EDM performance with multi-objective decision-making using copper-coated aluminum electrodes and TOPSIS methodology for Ti-6Al-4V machining

Surface modification of a magnesium alloy by electrical discharge coating with a powder metallurgy electrode

Multi-objective Optimization of Electric Discharge Machining of Al-SiCp Composite by Taguchi-PCA, Firefly and Cuckoo Search Algorithm

Effect of Al7075 and Activated Carbon reinforced Composite on Optimizing WEDM Responses

Investigation of aluminum alloy 6061 in Wire-EDM regarding surface roughness and material removal rate by adopting optimization techniques

Experimental investigation to assess the surface integrity in WEDM of Al-based hybrid composite material

Die-sinking EDM of Al6061-T6: interactions between process parameters, process performance, and surface characteristics

Machinability Analysis and Optimization of Electrical Discharge Machining in AA6061-T6/15wt.% SiC Composite by the Multi-criteria Decision-Making Approach

Synthesis of Stir-Cast AA7050/5%B4C Composite and Optimization of EDM Response Parameters Using Taguchi Analysis

Taguchi optimization of Wire EDM process parameters for machining LM5 aluminium alloy

Experimental investigation, modeling and optimization of wire EDM process parameters for machining AA2024-B4C self-lubricating composite

Experimental Investigations On The Electrochemical Machining Of D3 Die Steel Material And Multi-Objective Parameter Optimization

Optimization by AHP-ARAS of EDM Process Parameters on Machining AA7050-10%B4C Composite