Abstract:Одним из главных факторов обеспечения надежности и безопасности объектов магистральных трубопроводов является оценка их технического состояния как на стадии строительства, так и в процессе эксплуатации. Объектом исследования определен дифракционно-временной метод ультразвукового контроля (ДВМ), основным преимуществом которого относительно эхо-метода является, по заявлениям производителей оборудования, малая зависимость вероятности выявления дефекта от его ориентации и формы и, как следствие, повышение достоверности оценки высоты и глубины залегания дефекта. Целью работы является совершенствование системы оценки качества сварных соединений на объектах трубопроводного транспорта нефти и нефтепродуктов путем уточнения границ применимости ДВМ. В качестве предмета исследования рассматриваются факторы, определяющие указанные границы: ограничение области контроля из-за наличия мертвых зон, ограничение возможности измерения высоты дефекта параметром разрешающей способности метода, ограничения вследствие влияния особенностей геометрии или коррозионных повреждений сварных соединений, ограничение по ориентации, форме и месту расположения дефектов. В результате выполненных исследований выявлены границы применимости дифракционно-временного метода контроля на объектах трубопроводного транспорта, обусловленные исследованными факторами. One of the main factors of ensuring the reliability and safety of main pipeline facilities is the estimation of their technical condition both at the construction stage and during operation. The object of the study is the ultrasonic time-of-flight-diffraction method (TOFD). According to the information from the equipment manufacturers, TOFD main advantage relative to the echo method is the low dependence of the defect detection probability on its orientation and shape and, as a result, an increase in the reliability of defect height and depth estimation. The purpose of the work is to improve the system for assessing the quality of welded joints at oil and oil product pipeline facilities by clarifying the limits of TOFD applicability. The factors that determine these limits are considered as the study subject: the limitation of inspection area due to the presence of dead areas, the limitation of the possibility to measure the defect height by the resolution parameter of the method, the limitations imposed by the geometry of welded joints, limitation on the orientation, shape and location of defects. As a result of the performed studies, the limits of the time-of-flight-diffraction method applicability at pipeline transport facilities, caused by the studied factors, have been revealed.

Analysis of the main problems arising during the recognition of the defect type based on the results of the dissolved gases analysis

Interpreting dissolved gases in transformer oil: A new method based on the analysis of labelled fault data

FAULT DIAGNOSIS OF INSULATION IN POWER TRANSFORMER BASED ON DISSOLVED GAS ANALYSIS METHOD

The DGA interpretation method using relative content of characteristic gases and gas-ratio combinations for fault diagnosis of oil-immersed power transformers

Limits of time-of-flight-diffraction method applicability at pipeline transport facilities

Development of an Online Detection Setup for Dissolved Gas in Transformer Insulating Oil

A Reviewed Turn at of Methods for Determining the Type of Fault in Power Transformers Based on Dissolved Gas Analysis

POLYETHYLENE GAS PIPELINES: PRACTICAL POSSIBILITIES TECHNICAL DIAGNOSTICS

Gassing Tendency of Fresh and Oxidative Aged Mixed Insulating Oils on Electric Sparking

Difference Analysis of Dissolved Gas in Natural Ester Insulating Fluids under Typical Electrical and Thermal Faults: an Experimental Study

Fault Diagnosis Method for Power Transformers Based on Patterns of Dissolved Gases in the Oil

Calculation of Dissolved-Gas Limit Values and Detection of Thermal Defects in a Group of Arc Furnace Transformers

Failure Monitoring and Asset Condition Asssessment in Gas Supply Systems

Developing Characteristics of Oil-immersed Transformer Internal Fault with Dignostic Method Using Convergence Patterns of Free Gas

Partial discharges and diagnostics of high-voltage equipment

Qualimetric Analysis of Pipelines with Corrosion Surfaces in the Monitoring System of Oil and Gas Enterprises

Evolution of graphical methods for the identification of insulation faults in oil-immersed power transformers: A review

EXPERIENCE IN THE APPLICATION OF NON-DESTRUCTIVE TESTING METHODS CONTROL IN THE OPERATION OF PRODUCTS

Research Progress of the Dissolved Gas Analysis in Synthetic Ester Insulating Oil under Electrical Faults

The Analysis of the Influence of Various Factors on the Development of Stress Corrosion Defects in the Main Gas Pipeline Walls in the Conditions of the European Part of the Russian Federation

Analysis of Abnormal Detection Data of Dissolved Gases in 500kV Transformer Oil