Abstract:This study investigated the metallurgical, mechanical properties and quality of coatings fabricated by direct laser metal deposition (DLMD) on Ti-6Al-4V, which were affected by the DLMD optimized process parameters. A 3-kW continuous wave ytterbium laser system (YLS) attached to a KUKA robot was used for the process. An analysis was conducted to determine the quality of the coatings in terms of hardness and wear resistance. Variables such as the time of interlayer deposition, thickness of the substrate, the initial temperature of the substrate, and the number of deposited layers were also investigated. The independent/collective effect that each process parameter had on the metallurgical and mechanical properties of the deposited Ti-6Al-4V were made clear when the processing parameters were varied. Minute pores/defects that significantly affect the metallurgical and mechanical properties of clads were also identified. The results obtained from the designed experiments showed that the depth of Heat Affected Zone (HAZ) was inversely proportional to the thickness of the substrate; as the thickness of the substrate was increased, the HAZ depth decreased. Moreover, the intensity of the laser power also affects the HAZ depth. In addition, it was discovered that the initial conditions of the substrate at room temperature also affected the coatings in relation to pre-heated conditions. The analysis conducted in identifying and quantifying the porosity showed indication that the factors such as scanning speed, laser power and powder feed rate had a predominant influence on the porosity. The grain form and structure as well as the mechanical properties of the cladded layer were significantly affected by the optimized process parameters of DLMD process. The parameters investigated had a significant impact on the hardness and wear resistance performance. Furthermore, the results revealed that the highest hardness of one of the coatings was 1.97-times the substrate which had a hardness value of 302 HV. The outstanding wear resistance performance of Al-Si-Sn-Cu/Ti-6Al-4V composite coating is attributed to major hard intermetallic phases.

Deposition of Multi-Ceramic Aluminium-Matrix Composite Coating by Direct Laser Deposition

Effect of Process Parameters on Microstructure and Properties of AlCoCrFeNi-WC-WS2 Composite Coating Prepared by Laser Cladding

Wear Resistance of Aluminum Matrix Composites’ Coatings Added on AA6082 Aluminum Alloy by Laser Cladding

Microstructures and Properties of Laser Cladding Al-TiC-CeO₂ Composite Coatings

Laser Synthesis of Titanium Aluminides Matrix Composite Coatings Reinforced by In-Situ Titanium Carbide Particles on Ti-6Al-4V Substrate

In-Situ Synthetic Tib2 Particulate Reinforced Metal Matrix Composite Coating on Aa2024 Aluminum Alloy by Laser Cladding Technology

Development and characterization of Ni60 alloy and SiC ceramic reinforced metal matrix composite coating on Ti-6Al-4V using laser cladding with coaxial powder feeding system

STUDY ON WEAR RESISTANCE OF LASER CALDDING Fe-BASED COMPOSITE COATINGS REINFORCED BY IN-SITU MULTIPLE CARBIDE PARTICLES

The Interplay of Thermal Gradient and Laser Process Parameters on the Mechanical Properties, Geometrical and Microstructural Characteristics of Laser-Cladded Titanium (Ti6Al4V) Alloy Composite Coatings

Surface microstructures and properties of oxide-reinforced FeCrAl matrix composite coatings prepared by laser cladding on a ferritic-martensitic steel

Microstructure and Mechanical Properties of Multiple In-Situ-Phases-Reinforced Nickel Composite Coatings Deposited by Wide-Band Laser

Microstructure and Properties of TiAl Composite Coatings Prepared by Laser Cladding under Multi-Phase β0/CoAl2Ti Phase Strengthening

Microstructure and Properties of 7075/al2o3 Composite Coatings Prepared by Supersonic Laser Deposition

Microstructure and Tribological Behavior of Laser Cladding TiAlSi Composite Coatings Reinforced by Alumina–titania Ceramics on Ti–6Al–4V Alloys

High Performance NbMoTa-Al<sub>2</sub>O<sub>3</sub> Multilayer Composite Structure Manufacturing by Laser Directed Energy Deposition

High Performance NbMoTa–Al2O3 Multilayer Composite Structure Manufacturing by Laser Directed Energy Deposition

Microstructure characteristics of titanium aluminide matrix composite coatings made by laser cladding on titanium alloy substrate

Data related to optimized process parameters influence on hardness, microstructural evolution and wear resistance performance of Al-Si-Sn-Cu/Ti-6Al-4V composite coatings

In-Situ Synthesis of Mosi2/Sic Composite Coating by Laser Cladding

Surface reinforcements of TA15 titanium alloy with laser induced Co base multiphase composites

Online assessment of TiC decomposition in laser cladding of metal matrix composite coating