Abstract:3D-печать представляет собой инновационный метод аддитивного производства с цифровым управлением, который позволяет создавать архитектурные и структурные компоненты без опалубки, в отличие от традиционных методов строительства с использованием бетона. Наиболее важные свойства свежеприготовленного бетона — экструдируемость и сохраняемость формы уложенного материала, которые тесно связаны с удобо укладываемостью и допустимым временем работы со смесью*. На эти характеристики существенно влияют пропорции между содержанием компонентов смеси и наличие в ее составе химических добавок. Настоящее исследование посвящено оптимизации дозировки материалов при изготовлении смеси для 3D-печати. При разработке рецептуры смеси использовались цемент, зола-унос, микрокремнезем, мелкий заполнитель и вода, а также химические добавки. Результаты настоящего исследования показывают, что как оптимизация смеси с использованием различных комбинаций цементных вяжущих, так и выбор оптимальной дозировки химических добавок очень важны для получения бетона, пригодного для 3D-печати. The printing process is a novel digitally-controlled additive manufacturing method which can build architectural and structural components without formwork, unlike conventional concrete construction methods. The most important fresh properties are extrudability and buildability, which have mutual relationships with workability and open time. These properties are greatly influenced by the mix proportions and the presence of superplasticiser, retarder, accelerator and polypropylene fibres. The present study is about optimisation of material quantity to obtain a 3D printable mix with 3D printer. Cement, fly ash, silica fume, fine aggregate, water and chemical admixture are used for developing a 3D printable mix and optimum dose of chemical admixture such as PC base chemical admixture and Viscosity Modifying Admixture (VMA) is used to optimise the 3D printable mix. The study indicated that the dosage of superplasticizer needed to achieve the similar flow value increases as a/b increases. The plastic viscosity increased by about 35 % when a/b increased from 0.75 to 0.9. The flow was ranging from 160 to 225 mm which indicates dependency on the material type and packing density. Study also highlighted that yield stress of mix is important to achieve buildability and low yield stress value can lead to collapse of layers and will also prevent layer wise buildability. The optimum dose of polypropylene fibre was found to be 0.1 % to achieve 3D printable mix without clogging or shrinkage crack. The open time is found to be about 12—15 minutes for the materials. Studies reported in this paper highlights that both mix optimisation with different combination of cementitious binders and selection of optimum dosage of superplasticizer and VMA are very critical in achieving a 3D printable concrete.

Mixing approach for 3D printable concrete: method of addition and optimization of superplasticizer dosage

Influence of Superplasticizer Type and Dosage on Early-age Drying Shrinkage of Cement Paste with Consideration of Pore Size Distribution and Water Loss

Influence of Superplasticizers on Early Age Drying Shrinkage of Cement Paste with the Same Consistency

A New Model to Predict the Optimal Mix Design of Self-Compacting Concrete Considering Powder Properties and Superplasticizer Type

D-optimal design of experiments applied to 3D high-performance concrete printing mix design

Role of material selection in mix optimization of 3D printable concrete

A novel method for improving the printability of cement-based materials: Controlling the releasing of capsules containing chemical admixtures

Effectiveness Assessment of Superplasticizer Admixtures: Case of Self-compacting Concrete Reinforced with Fine Mineral Fillers

D3 method: Direct and delayed dosing: New insights into specific surface area modification by superplasticizers

Comparative Evaluation of the Applicability of 3D Printing Mortar with Different Waste Powders

Effect of Additives on the Rheological and Mechanical Properties of Microfine-Cement-Based Grout

Mix-Design Optimization of Self-Compacting Paste Incorporating Powdery Industrial Solid Wastes Based on a Paste Rheological Threshold Theory

A Novel Approach to Methoxy Polyethylene Glycol-Grafted Sulfonated Poly(maleic Anhydride-Alt-styrene) As Superplasticizers in Cement Pastes

Effect of supplementary cementitious materials on properties of 3D printed conventional and alkali-activated concrete: A review

Development of concrete mixes for 3D printing using simple tools and techniques

Study of 3D printed concrete with low-carbon cementitious materials based on its rheological properties and mechanical performances

Research on a Mix Design Method of Self-Compacting Concrete Based on a Paste Rheological Threshold Theory and a Powder Equivalence Model

Workability and Mechanical Properties of Superplasticized Microfine Cement Grouts

Nanocrystalline Cellulose to Reduce Superplasticizer Demand in 3D Printing of Cementitious Materials

Influence of mixing time and superplasticizer dosage on self-consolidating concrete properties

Improving printability of limestone-calcined clay-based cementitious materials by using viscosity-modifying admixture