Abstract:2,6-diamino-3,5-dinitropyrazine-1-oxide (LLM-105) is a typical high-energy and low-sensitivity energetic material (EM), which has excellent detonation performance and thermal stability. Based on quasi-harmonic approximation, the dispersion corrected density functional theory was used to study the intermolecular interactions and thermodynamic properties of energetic LLM-105 crystal. By introducing the zero-point energy and temperature effect corrections, PBE-D3 dispersion correction scheme could significantly improve the calculation accuracy of structural parameters at experimental temperature (294 K). The temperature dependent lattice parameters and thermal expansion coefficients exhibit strong anisotropy, especially the thermal expansivity in b -axis orientation (intermolecular layers) is much higher than that in the ac plane (intramolecular layers). Through Hirshfeld surface and fingerprint analysis, it was found that the intermolecular interactions of LLM-105 are mainly O···H hydrogen bonding interactions. The change of intermolecular interactions would result in the rotation of nitro group, which could contribute to form new hydrogen-bonding interaction pattern. Mulliken population analysis shows that the bond order of C−NO 2 bond is more sensitive to the change of temperature, which may be the trigger bond for the high-temperature decomposition reaction of LLM-105. The fundamental thermodynamic properties of EMs can not only provide key parameters for mesoscopic or macroscopic thermodynamic simulations, but also gain theoretical insights into the temperature effects of EMs. Specific heat capacity reflects the amount of heat to be supplied to heat the matter and it is important to the risk assessment of EMs during storage or when exposed to external thermal stimuli. Herein, the basic thermodynamic parameters, such as heat capacity, entropy, bulk modulus and elastic constants under different conditions are predicted. Among them, the calculated heat capacity and entropy describe the nonlinear behaviors within the temperature range of 0−500 K, and the calculated isobaric heat capacity C p ( T ) is in good agreement with the available experimental measurements. The elasticity of materials describes the macroscopic response of crystals to external forces, and the bulk modulus B 0 of molecular crystals can be determined through the equation of state, which is an important parameter for evaluating material stiffness. The bulk modulus under adiabatic conditions is in reasonable agreement with experimental values, and the evolution of bulk modulus with temperature reflects the softening behaviors of LLM-105 at temperature. Furthermore, the complete set of second-order elastic constants (SOECs) of LLM-105 is calculated and 13 independent SOECs ( C 11 , C 12 , C 13 , C 15 , C 22 , C 23 , C 25 , C 33 , C 35 , C 44 , C 46 , C 55 , C 66 ) are predicted. With the increasing temperature, all elastic constants gradually decrease due to the weaken of intermolecular interactions of LLM-105. Overall, these results would fundamentally provide a deep understanding of temperature effects and serve as a reference for the experimental measurement of the thermodynamic parameters of EMs.

A novel modification method for the dynamic mechanical test using thermomechanical analyzer for composite multi-layered energetic materials

Investigation of thermomechanical properties of solid rocket propellant used in multi-barrel rocket systems

Molecular dynamic simulation of performance of modified BAMO/AMMO copolymers and their effects on mechanical properties of energetic materials

Real-time Evaluating Temperature-Dependent Interfacial Shear Strength of Thermoplastic Composites Based on Stress Impedance Effect of Magnetic Fibers

Thermo-mechanical Investigation of Composite High-Pressure Hydrogen Storage Cylinder During Fast Filling

Definition of test parameters for dynamic mechanical testing of polymeric implant materials

Mechanical behavior and optimization of constitutive prediction model for Epoxy/Al energetic composite materials considering temperature and strain rate effects

Dynamic-mechanical response of carbon fiber laminates with a reactive thermoplastic resin containing phase change microcapsules

Assessment of Thermal Transitions by Dynamic Mechanical Analysis (DMA) Using a Novel Disposable Powder Holder

Multiscale damage evolution and fracture for thermal aging energetic material based on mesoscopic observation and molecular dynamics simulation

Experimental Investigation on the Influence of Confining Pressure on Thermal Aged CMDB Propellant

The proper glass transition temperature of amorphous polymers on dynamic mechanical spectra

Mechanical and Thermal Analysis of Duroplastic Matrix Composites over a Range of Temperatures

The Constant-Stress, Constant-Heating-Rate Test: A Novel Method for Characterizing Transient Mechanical Behavior of Metallic Materials

Dynamic mechanical analysis (DMA) in fiber research

Mechanical Behavior of Polytetrafluoroethylene/Aluminum Energetic Materials under High and Low Temperature Conditions

Study on mechanical and thermal properties of a modified epoxy resin

Theoretical study on intermolecular interactions and thermodynamic properties of LLM-105

Dynamic Mechanical Properties and Modification of Fracture Criteria of 6061-T651 Aluminum Alloy

Mechanical Testing and Modeling of the Time–Temperature Superposition Response in Hybrid Fiber Reinforced Composites

A Novel Method of Improving the Mechanical Properties of Propellant Using Energetic Thermoplastic Elastomers with Bonding Groups