TiO 2 with controllable oxygen vacancies for efficient isopropanol degradation: photoactivity and reaction mechanism

Shuyang Wu,Kana Ishisone,Yuan Sheng,Manoel Y. Manuputty,Markus Kraft,Rong Xu

DOI: https://doi.org/10.1039/d1cy00417d

2021-01-01

Abstract:Flame-synthesized TiO 2−x with controllable defects exhibits a remarkable photooxidation efficiency of gaseous isopropanol with the reaction mechanism investigated.

chemistry, physical

What problem does this paper attempt to address?

Progress in Photocatalytic Oxidation of Organic Contaminants Using TiO2 as the Catalyst

黄琮,王良焱,朱春媚,郑少健,陈非力,冯满枝,杨宝山

2001-01-01

Abstract:In this paper, the mechanism of semiconductor photocatalytic oxidation in the degradation of organic contaminants was studied, and the advantage of using TiO2 as the catalyst was introduced. In addition, the recent research on the reactor, the photocatalytic kinetics and how to raise the catalytic effect were summarized. Moreover, the future development was prospected.
Rational Design of Nitrogen and Carbon Co-Decorated Mesoporous TiO2 Composites for Photocatalytic Selective Oxidation of Alcohols

Changsheng Cao,Yaru Shen,Yu Shao

DOI: https://doi.org/10.1016/j.mcat.2024.114483

IF: 4.6

2024-01-01

Molecular Catalysis

Abstract:Photocatalytic organic synthesis has attracted much attention in recent years. Herein, a N and C co-decorated mesoporous TiO2 (mp-NCT) photocatalyst was synthesized for selective oxidation of alcohols. Notably, the asprepared mp-NCT composites possess large specific surface areas and mesoporous structures, which could provide sufficient active sites and improve mass transfer. Furthermore, the co-doping of N and C species could not only extend the light absorption, but also tune the valence band of TiO2. Meanwhile, numerous oxygen vacancies and intra-band could be introduced, which helps to reduce the combination of the photogenerated carriers. As a result, the mp-NCT composites show excellent photocatalytic performance towards selective oxidation of benzyl alcohol and its derivatives to corresponding aldehydes under simulated sunlight irradiation. Mechanism studies revealed that the photogenerated electrons, holes and high dynamic equilibrium concentration of O2 center dot- radicals were responsible for the efficient conversion of alcohols to aldehydes.
Unraveling the Photocatalytic Mechanisms on TiO2 Surfaces Using the Oxygen-18 Isotopic Label Technique

Xibin Pang,Chuncheng Chen,Hongwei Ji,Yanke Che,Wanhong Ma,Jincai Zhao

DOI: https://doi.org/10.3390/molecules191016291

IF: 4.6

2014-10-10

Molecules

Abstract:During the last several decades TiO2 photocatalytic oxidation using the molecular oxygen in air has emerged as a promising method for the degradation of recalcitrant organic pollutants and selective transformations of valuable organic chemicals. Despite extensive studies, the mechanisms of these photocatalytic reactions are still poorly understood due to their complexity. In this review, we will highlight how the oxygen-18 isotope labeling technique can be a powerful tool to elucidate complicated photocatalytic mechanisms taking place on the TiO2 surface. To this end, the application of the oxygen-18 isotopic-labeling method to three representative photocatalytic reactions is discussed: (1) the photocatalytic hydroxylation of aromatics; (2) oxidative cleavage of aryl rings on the TiO2 surface; and (3) photocatalytic decarboxylation of saturated carboxylic acids. The results show that the oxygen atoms of molecular oxygen can incorporate into the corresponding products in aqueous solution in all three of these reactions, but the detailed incorporation pathways are completely different in each case. For the hydroxylation process, the O atom in O2 is shown to be incorporated through activation of O2 by conduction band electrons. In the cleavage of aryl rings, O atoms are inserted into the aryl ring through the site-dependent coordination of reactants on the TiO2 surface. A new pathway for the decarboxylation of saturated carboxylic acids with pyruvic acid as an intermediate is identified, and the O2 is incorporated into the products through the further oxidation of pyruvic acid by active species from the activation of O2 by conduction band electrons.

chemistry, multidisciplinary,biochemistry & molecular biology
Enhanced Photocatalytic Oxidation of Isopropanol by HKUST-1@TiO2 Core–Shell Structure with Ultrathin Anatase Porous Shell: Toxic Intermediate Control

Hongmei Wang,Tao Yu,Xin Tan,Huabin Zhang,Peng Li,Huimin Liu,Li Shi,Xiangli Li,Jinhua Ye

DOI: https://doi.org/10.1021/acs.iecr.6b01400

2016-01-01

Industrial & Engineering Chemistry Research

Abstract:Poor adsorption of reactants and intermediates as well as low mineralization rate greatly restrict the application of common semiconductor photocatalyst TiO2 for air purification. A plausible solution would be to integrate metal–organic frameworks (MOFs) materials with good gas adsorption property with traditional photocatalytic material TiO2 with exciton generation. A core–shell structured photocatalyst with functional MOFs HKUST-1 (Cu3(BTC)2, BTC = 1,3,5 benzenetricarboxylate) as core and porous ultrathin anatase film as shell was synthesized. The composite photocatalyst was characterized in detail, and isopropanol degradation experiments were performed to evaluate the photocatalytic performances. The experimental results revealed that HKUST-1 can provide a special pathway for photogenerated electrons migration and thus restrain the recombination of electrons and holes to increase the photocatalytic efficiency. Furthermore, the capture of reactants and intermediates was also enhanced due to the unique M...
Distribution And Concentration Of Surface Oxygen Vacancy Of Tio(2)And Its Photocatalytic Activity

Sheng Meng

DOI: https://doi.org/10.1088/1361-6463/ab9d99

2020-01-01

Abstract:Oxygen vacancies in transition-metal oxides can facilitate photocatalysis activity critical for environmental remediation and solar energy conversion. Investigation of photocatalytic activity of TiO(2)with different amounts of the oxygen vacancies can provide fundamental insights into the oxygen-vacancy-dependent reaction mechanisms. Here, the oxygen vacancies in TiO(2)nanoparticles were investigated by the combination of transmission electron microscopy with electron energy loss spectra, x-ray near-edge structures, and x-ray absorption techniques. The results demonstrate that the oxygen vacancies mainly exist at the surface of TiO(2)and the crystalline structure of TiO(2)almost keeps no change during annealing under the different oxygen pressures at 500 degrees C. The exact quantity and distribution of the oxygen vacancies in TiO(2)nanoparticles were obtained. The surface oxygen vacancies on TiO(2)significantly enhance photocatalytic activity for Rhodamine B degradation and hydrogen generation. The formation of oxygen vacancies at the TiO(2)surfaces is responsible for engineering the band gap of TiO(2)and tailoring their electronic structures, and promoting light absorption and enhancement photocatalysis. This work could provide new insights into the understanding of the photocatalytic activity enhancement by the surface oxygen vacancies.
Cu 2 O/SrTi 1- x Cr x O 3 Heterojunction Photocatalyst for the Efficient Degradation of Isopropanol under Visible Light Irradiation

Zhonghua Li,Xuefan Zhang,Ping Chen,Zihan Shen,Rui Wang,Qiya He,Shuo Zhang,Shaozhong Chang,Jiaming Tian,Huigang Zhang

DOI: https://doi.org/10.1021/acs.langmuir.2c02007

IF: 3.9

2022-11-04

Langmuir

Abstract:A heterojunction of Cu(2)O and Cr-doped SrTiO(3) (SrTi(1-x)Cr(x)O(3)) was designed for selective photocatalytic isopropanol (IPA) oxidation under visible light irradiation. The photocatalytic oxidation of IPA was measured in a fixed-bed reactor. Cr dopants can increase the light absorption and improve the activity of the catalyst. The formation of the Cu(2)O/SrTi(1-x)Cr(x)O(3) heterojunction can further broaden the absorption range of lights and dramatically increase the photocatalytic activity...

chemistry, multidisciplinary, physical,materials science
Flame Synthesized Blue TiO 2− x with Tunable Oxygen Vacancies from Surface to Grain Boundary to Bulk

Shuyang Wu,Manoel Y. Manuputty,Yuan Sheng,Haojing Wang,Yong Yan,Markus Kraft,Rong Xu

DOI: https://doi.org/10.1002/smtd.202000928

IF: 12.4

2020-12-18

Small Methods

Abstract:Fabrication of nonstoichiometric metal oxides containing oxygen vacancies (OVs) has been an effective strategy to modulate their (photo)catalytic or (photo)electrochemical performances which are all affected by charge transfer at the interface and in the bulk. Considerable efforts are still needed to achieve tunability of OVs, as well as their quantitative characterization. Herein, a one‐step flame synthesis method is reported for the first time for fast fabrication of blue TiO2−x with controllable defect content and location. Temperature‐programmed oxidation (TPO) analysis is applied for the first time and found to be an excellent technique in both differentiating and quantifying OVs at the surface, grain boundary (GB), and bulk of TiO2−x. The results indicate that a moderate level of OVs can greatly enhance the charge transfer. Importantly, the OVs locked at GBs due to the thermal sintering of nanoparticles during the synthesis can facilitate the anchoring and reduction of Pt species.

materials science, multidisciplinary,chemistry, physical,nanoscience & nanotechnology
Promoting ring-opening efficiency for suppressing toxic intermediates during photocatalytic toluene degradation via surface oxygen vacancies

Xing'an Dong,Wen Cui,Hong Wang,Jieyuan Li,Yanjuan Sun,Haiqiang Wang,Yuxin Zhang,Hongwei Huang,Fan Dong

DOI: https://doi.org/10.1016/j.scib.2019.04.020

2019-05-30

Abstract:Aromatic ring-opening process is well recognized as the rate-determining step for catalytic toluene degradation. In photocatalytic toluene degradation, the toxic intermediates with harmful effects may be generated. To clarify the precise reaction mechanism and control the toxic intermediates generation, a closely combined in situ DRIFTS and DFT calculation is utilized to address these important issues. We construct the BiOCl with oxygen vacancies (OVs) and reveal the structure of OVs. The defect level caused by oxygen vacancies could promote the light adsorption and charge separation, which further boosts the activation of ring-opening species and enhances the generation process of free radicals. The reaction energy barriers of four possible ring-opening processes on defective BiOCl (OVBOC) are all declined in comparison with perfect BiOCl (BOC). The existence of oxygen vacancies could smooth the rate-determining step so the ring-opening efficiency of photocatalytic toluene degradation is highly increased. Most importantly, the methyl species would be further oxidized and tend to open the benzene-ring at benzoic acid on BOC while the ring would be broken at the benzyl alcohol on OVBOC. These results indicate that the toluene degradation pathway is shortened via the surface OVs, which enables the production of radicals with high oxidation capability for the accelerated chain scission of the ring-opening intermediates. Finally, the efficiency of the key ring-opening process could be enormously improved and toxic intermediates are effectively restrained. The present work could provide new insights into the design of high-performance photocatalysts for efficient and safe degradation of VOCs in air.
Kinetic pathways of sub-bandgap induced electron transfer in Ag/TiO2 and the effect on isopropanol dehydrogenation under gaseous conditions

Liping Wen,Baoshun Liu

DOI: https://doi.org/10.1039/d3cp05897b

2024-04-03

Abstract:Electron transfer and its kinetics play a major role in the photocatalysis of metal/semiconductor systems. Using in situ photoconductances, in situ photoabsorption, and photoinduced spectroscopic techniques, the present research aimed to gain a deep insight into electron transfer pathways and their kinetics for Ag/TiO2 systems under sub-bandgap light illumination and gaseous conditions. The results revealed that electrons generated in TiO2 can transfer to Ag nanoparticles at fast rates, and plasmon-generated electrons in Ag nanoparticles can also transfer to TiO2. However, it was found that plasmon-assisted hot electron transfer efficiency is much lower than the electron transition from the valence band to the conduction band of TiO2. Rather than plasmonic active spots, the results showed that Ag nanoparticles acted as co-catalyst sites bridging electron transfer to recombination in a methanol-containing N2 atmosphere. As a result, photocatalytic isopropanol dehydrogenation was decreased. Independent of Ag decorations, it was also indicated that isopropanol dehydrogenation mainly occurred over TiO2 surfaces; therefore, Ag nanoparticles did not increase photocatalytic activities. Our results may provide a different viewpoint on sub-bandgap light-induced Ag/TiO2 photocatalysis under gaseous conditions; this may also facilitate the understanding of the photocatalytic mechanism of metal/semiconductor systems.
The synergic removal mechanism for photothermocatalytic toluene over single-atom Pt/TiO 2 catalysts via flame spray pyrolysis

Xing Yuan,Chaohe Zheng,Zuwei Xu,Qinghua Yang,Tiantian Zhang,Xi Luo,Haibo Zhao

DOI: https://doi.org/10.1016/j.proci.2022.07.061

IF: 6.535

2022-10-19

Proceedings of the Combustion Institute

Abstract:Photothermocatalytic oxidation is an environmentally-friendly, low-temperature, and high-efficient method to remove the air pollutant. Yet, the lack of active, inexpensive, and superior stability catalysts has greatly limited its extensive utilization. In this work, the effect of single-atom Pt loading on TiO 2 support has been theoretically and experimentally studied to improve photothermocatalytic performance for the toluene combustion through flame spray pyrolysis (FSP). Pt loading can play two crucial roles into TiO 2 optimization: (1) The low-valence Pt cation incorporated into TiO 2 lattice is dramatically responsible for the anatase-rutile transformation (ART) and formation of sufficient oxygen vacancies; (2) Introducing the defect energy level and Pt-3d orbitals remarkably promote the charge separation efficiency of single-atom catalysts. Moreover, the existence of single-atom Pt nanoparticles can signally boost the activity of surface adsorbed and lattice oxygen, as well as substantially reduce the oxygen vacancy formation energy. Thus, the toluene removal under light irradiation reaches 90% conversion below 160 °C and is maximally 18 °C lower than that under only thermocatalytic oxidation. It is attributed to larger specific surface area (SSA), outstanding low-temperature reducibility, extremely dispersed hybrid PtO x , more surface active oxygen, and higher mobility of bulk oxygen. Interestingly, when the oxygen-fuel equivalent ratio φ distinctly increases by shifting precursor solvent from xylene to ethanol, the photothermocatalytic property of toluene can be remarkably enhanced on single-atom Pt catalysts. It is due to the higher Pt dispersion resulting from more intense burning and drastic turbulent mixing, as well as the superior ratio of the metallic Pt active sites originating from higher flame temperature. Eventually, the rate-determining step of C 7 H 8 combustion on Pt/TiO 2 and Cu/TiO 2 slab are all the CC bond fracture of maleic anhydride to form acetic anhydride species, with the energy barriers of 112.03 and 188.74 kJ/mol, respectively.

energy & fuels,engineering, chemical, mechanical,thermodynamics
Design of TiO2-X nanotubes with controllable oxygen vacancy concentration and performance study of selective oxidation of benzyl alcohol

Chunling Hu,Peng Chen,Qi Li,Keliang Wu,Yuwei Liang,Jianning Wu,Jichang Liu,Xuhong Guo,Zhiyong Liu

DOI: https://doi.org/10.1007/s10853-024-10101-z

IF: 4.5

2024-10-05

Journal of Materials Science

Abstract:As one of the most important synthetic fine chemicals and pharmaceuticals, benzaldehyde is widely used in pharmaceuticals, dyestuffs, fragrances and pesticides. It is still a difficult challenge to promote the conversion of benzyl alcohol to benzaldehyde by photocatalysis with high selectivity and high conversion. In this paper, the content of the reactive substance ·O 2 − is regulated by constructing suitable oxygen vacancies in TiO 2 nanotubes, thus improving the photocatalytic conversion and selectivity. Herein, we have prepared TiO 2-X 1D nanotubes enriched with different concentrations of oxygen vacancies by template method, hydrolysis of tetrabutyl titanate and vacuum annealing. By constructing suitable concentrations of oxygen vacancies in the TiO 2 material, we can increase its ability to adsorb oxygen to produce more ·O 2 − on the one hand, and help to construct defective energy levels to prevent the compounding of photogenerated charge carriers to enhance photocatalytic activity on the other. As a result, the best photocatalytic activity of TiO 2-X nanotubes obtained by vacuum annealing at 300 °C was 78% for benzyl alcohol conversion and 88% for benzaldehyde production selectivity, which is 2.6 and 1.8 folds higher than that of pristine TiO 2 nanoparticles. Our work may provide insights for designing efficient photocatalysts for selective oxidation of benzyl alcohols.

materials science, multidisciplinary
Wavelength-Dependent Activity of Oxygen Species in Propane Conversion on Rutile TiO2(110)

Yuemiao Lai,Yi Zeng,Fangliang Li,Xiao Chen,Tao Wang,Qing Guo

DOI: https://doi.org/10.1021/acs.jpclett.4c01035

2024-07-11

Abstract:Photocatalytic oxidative dehydrogenation of propane (C3H8) into propene (C3H6) under mild conditions holds great potential in the chemical industry, but understanding how active species participate in C3H8 conversion remains a significant challenge. Here, the wavelength-dependent activities of bridging oxygen (Ob2-) and the Ti5c-bound oxygen adatom (OTi2-) of model rutile (R) TiO2(110) in C3H8 conversion have been investigated. Under 257 and 343 nm irradiation, hole-trapped OTi- and Ob- can abstract the hydrogen atom of C3H8, forming the CH3CH•CH3 radical and C3H6. However, the rate of C3H8 conversion with hole-trapped Ob- is strongly dependent on the wavelength, primarily producing the C3H7• radical. In the case of hole-trapped OTi-, C3H6 is the main product, which is nearly independent of wavelength. The differences in the wavelength-dependent activity and product selectivity are likely due to dynamic control rather than thermodynamic control. The result provides a deeper understanding of the dynamic processes involved in the conversion of light alkanes in TiO2 photocatalysis.
Competitive photooxidation of small colorless organics controlled by oxygen vacancies under visible light

Jianghui Sun,Xiyang Ge,Yixuan Gao,Min Zhang,Qi Zhao,Guohua Hou,Xiaoni Wang,Yiyan Yin,Jin Ouyang,Na Na

DOI: https://doi.org/10.1039/d4sc04531a

IF: 8.4

2024-09-25

Chemical Science

Abstract:Visible-light photooxidation sensitized by surface attachment of small colorless organics on semiconductor photocatalysts has emerged as an economical method for photocatalytic synthesis or degradation. In particular, heteroatom (X = N and Cl)-containing substrates could undergo either C–N coupling or dechlorination degradation via sensitizing TiO 2 , but the mechanism in conducting the competitive visible-light sensitized photooxidations is still vague. Herein, the visible-light photooxidation of colorless 4-chlorobenzene-1,2-diamine ( o -CAN) on TiO 2 was revealed, contributing to selective C–N coupling rather than dechlorination. Oxygen vacancies (OVs) were in situ generated on the TiO 2 surface, which could be dominant in weakening the Cl–Ti adsorption of o -CAN and regulating the activation of O 2 for selective C–N coupling. The C–N coupling product, functionalized as the sensitizer, further promoted the visible-light photooxidation upon N–Ti and Cl–Ti coordination. This process was then confirmed by on-line mass spectrometric analysis, and the intermediates as well as their kinetics were determined. Thereby, theoretical calculations were employed to verify the roles of OVs in competitive photooxidation and lowering the energy barriers as well. Based on the comprehensive characterizations of both the catalysts and intermediates, this work has provided insights into competitive photooxidations under visible light.

chemistry, multidisciplinary
Oxygen Vacancy-Governed Opposite Catalytic Performance for C3H6 and C3H8 Combustion: The Effect of the Pt Electronic Structure and Chemisorbed Oxygen Species

Yarong Fang,Huijuan Li,Qi Zhang,Chenyang Wang,Jue Xu,Huan Shen,Ji Yang,Chuanqi Pan,Yuhua Zhu,Zhu Luo,Yanbing Guo

DOI: https://doi.org/10.1021/acs.est.1c07573

2022-03-01

Abstract:Revealing the role of engineered surface oxygen vacancies in the catalytic degradation of volatile organic compounds (VOCs) is of importance for the development of highly efficient catalysts. However, because of various structures of VOC molecules, the role of surface oxygen vacancies in different catalytic reactions remains ambiguous. Herein, a defective Pt/TiO2-x catalyst is proposed to uncover the different catalytic mechanisms of C3H6 and C3H8 combustion via experiments and theoretical calculations. The electron transfer, originated from the oxygen vacancy, facilitates the formation of reduced Pt0 species and simultaneously interfacial chemisorbed O2, thus promoting the C3H6 combustion via efficient C═C cleavage. The reduced Pt nanoparticles facilitate the robust chemisorption of bridging dimer O22- (Pt-O-O-Ti) species. This chemisorbed oxygen inhibits the C3H8 combustion by depressing C3H8 adsorption. This work offers insights for the rational design of highly efficient catalysts for activating the C═C bond in alkene or C-H bond in alkane.
Photooxidation of Isoprene by Titanium Oxide Cluster Anions with Dimensions up to a Nanosize

Shi-Ying Lv,Qing-Yu Liu,Yan-Xia Zhao,Sheng-Gui He

DOI: https://doi.org/10.1021/jacs.1c00326

IF: 15

2021-03-03

Journal of the American Chemical Society

Abstract:Titania (TiO2) nanoparticles are active photocatalysts, and isoprene (C5H8) is a biogenic volatile organic compound that contributes crucially to global particulate matter generation. Herein, the direct photooxidation of isoprene by titanium oxide cluster anions with dimensions up to a nanosize by both ultraviolet (UV) and visible (Vis) light excitations has been successfully identified through mass spectrometric experiments combined with quantum chemistry calculations. The potential role of "dry" titania in atmospheric isoprene oxidation has been revealed, and a clear picture of the photooxidation mechanism on titanium oxide nanoparticles has been provided explicitly at the molecular level. The adsorption of isoprene on the atomic oxygen radicals (O•–) of titanium oxide clusters leads to the formation of the crucial interfacial state (IS) within the band gap of titanium oxides. This IS is demonstrated to be the significant factor in delivering the electron from the π orbital of C5H8 to the Ti3d orbital in the photooxidation process (C5H8 + Ti4+–O•– → C5H8O + Ti3+) and creating photoactivity in the Vis region. It is revealed that after the photogeneration of the O•– radicals by UV excitation on the TiO2 particle surface, the subsequent reactions can be induced by Vis excitation through the IS. This multicolor strategy in both the UV and Vis regions can enhance the efficiency of solar energy harvesting and improve the product yield of the photocatalysis on TiO2 nanoparticles. New insights have been provided into both the atmospheric chemistry of isoprene and the photochemistry of TiO2 nanoparticles.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/jacs.1c00326?goto=supporting-info">https://pubs.acs.org/doi/10.1021/jacs.1c00326</a>.Additional TOF mass spectra and analysis, DFT-calculated cluster structures and reaction energetics, simulated UV–vis adsorption spectra, and charge transfer analysis (<a class="ext-link" href="/doi/suppl/10.1021/jacs.1c00326/suppl_file/ja1c00326_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

chemistry, multidisciplinary
Synthesis of Sandwich-Structured AgBr@Ag@TiO 2 Composite Photocatalyst and Study of Its Photocatalytic Performance for the Oxidation of Benzyl Alcohols to Benzaldehydes

Ping Zhang,Peiyi Wu,Shenyuan Bao,Zheng Wang,Baozhu Tian,Jinlong Zhang

DOI: https://doi.org/10.1016/j.cej.2016.08.015

IF: 15.1

2016-01-01

Chemical Engineering Journal

Abstract:Silver halide-based photocatalytic materials have been successfully used in organic contaminant degradation and disinfection, but their application in the oxidation of alcohols to aldehydes has never been reported. Herein, we fabricated sandwich-structured AgBr@Ag@TiO2 composite photocatalyst by a facile multistep route and for the first time studied its photocatalytic performance for the oxidation of benzyl alcohols to benzaldehydes. It was found that the porous TiO2 shell layer can be successfully anchored on the surface of AgBr core by a kinetics-controlled hydrolysis process and the thickness of TiO2 shell layer can be conveniently tuned by adjusting the addition amount of ammonia water during titanium source hydrolysis. The control experiments indicated that the O-2 plays a vital role in promoting the oxidation of benzyl alcohols while non-aqueous solvents are favorable to improving the reaction selectivity from alcohol to aldehyde. Compared to blank TiO2 and AgBr@Ag, sandwich-structured AgBr@Ag@TiO2 exhibited a drastically enhanced photocatalytic activity in terms of benzyl alcohol oxidation under visible light irradiation. The transient photocurrent and photoluminescence (PL) spectrum analyses confirmed that the core-shell structure can effectively promote the separation of photo-generated electrons and holes. The radical scavenging experiments revealed that superoxide radical (.O-2(-)) and hole (h(+)) are the main reactive species responsible for the transformation from benzyl alcohols to benzaldehydes. (C) 2016 Elsevier B.V. All rights reserved.
Photothermal Propane Dehydrogenation Catalyzed by VO x -Doped TiO 2 Nanoparticles

Xiangyang Ji,Yue Ma,Xiao Sun,Shaojia Song,Kun Yang,Weixin Huang,Chunming Xu,Bohan Feng,Jian Liu,Weiyu Song

DOI: https://doi.org/10.1021/acsanm.3c00794

IF: 6.14

2023-03-27

ACS Applied Nano Materials

Abstract:Propane direct dehydrogenation (PDH) has received much attention. How to effectively catalyze inert C–H bond activation is of great significance for industrial development. Pt-based catalysts show excellent activity but are limited by their expensive price. Cr-based catalysts are scarcely applied owing to their high toxicity. V-based catalysts are appropriate candidates for their cheap price and low toxicity, but they suffer from high energy consumption. The photothermal synergy effect induced by nonradiative relaxation is expected to make the C–H bond activation and hydrogen coupling process easier compared to bare thermal catalysis. Herein, a set of V/TiO2 nanoscale catalysts were synthesized. The optimized 3 wt % V/TiO2 catalyst (hereafter simplified as 3V) has a particle size of ∼26 nm, achieving a propylene production rate of 342 μmol·g–1·h–1 at 500 °C with UV–vis light radiation, which is 9.2% higher compared with bare thermal conditions. In situ radiation X-ray photoelectron spectroscopy (XPS) shows that photon injection leads to more electron-deficient V atoms (Vδ+, 5 > δ > 3). The strengthened Lewis acidity enhances the C3H8 activation as revealed by kinetic evidence and in situ C3H8-DRIFT measurements. The calculated molecular orbital diagrams show that the V atoms decrease the energy gap between the highest occupied orbital (HOMO) of C3H8 and the lowest unoccupied orbital (LUMO) of the model catalyst. This work describes an efficient photothermal synergy approach, specifically the nonthermal effect for promoting propane dehydrogenation.

materials science, multidisciplinary,nanoscience & nanotechnology
Photocatalytic propylene epoxidation with O 2 over 4,4′-dibromobenzophenone modified carbon nitride coupled with TS-1

Haonan Zhang,Changhe Lu,Shuai Wang,Qinhua Zhang,Qiang Zhou,Shuxu Zhu,Chong Qi,Mingbo Wu,Wenting Wu

DOI: https://doi.org/10.1016/j.seppur.2024.126837

IF: 8.6

2024-03-01

Separation and Purification Technology

Abstract:The utilization of O 2 for propylene epoxidation is a highly desirable reaction due to its 100 % atom economy. However, achieving this reaction under mild conditions presents a significant challenge. In this paper, we present a tandem reaction system that combines 4,4′-dibromobenzophenone (BP) modified carbon nitride (g-C 3 N 4 ) with titanium silicalite zeolite (TS-1) to enable the selective photooxidation of propylene into propylene oxide at room temperature, using O 2 as the oxygen source. The achieved production rate of propylene oxide was an impressive 1195 μmol/g cat. /h, with a selectivity exceeding 99 %. Furthermore, the catalyst exhibited no significant deactivation after 5 cycles. Spectra and in-situ capture experiments revealed that the reaction involved a two-step system, with photocatalytic production of H 2 O 2 and propylene epoxidation facilitated by H 2 O 2 ·H 2 O 2 was generated through O 2− and 1 O 2 pathways, with an in-situ utilization efficiency of H 2 O 2 reaching 82 %. This work presents a novel approach for the direct epoxidation of propylene using O 2 .

engineering, chemical
Characterization Of Tio2-Zro2 And Isopropanol Catalytic Conversion

Han Cheng-Hui,Liu Bing-Hua,Zhang Hui-Liang,Shen Jian-Yi

DOI: https://doi.org/10.1016/S1872-1508(06)60044-2

2006-01-01

Acta Physico-Chimica Sinica

Abstract:A series of TiO2-ZrO2 composite oxides were prepared by a coprecipitation method. They were characterized by N-2 adsorption, XRD, TEM, microcalorimetric adsorption of NH3 and CO2, infrared spectra of ammonia adsorption. In comparison with single metal oxide, amorphous composite oxides could be observed with mesoporous. structure and higher BET surface area (S-BET=218 m(2).g(-1)). Although the initial adsorption heat for all these samples did not vary significantly, composite oxides possessed more Bronsted acid sites than single oxide. With an increase in the incorporated amount of titania, the number of basic sites on the surface of composite oxides was decreased. In the absence of O-2, the values of selectivity for propene exceeded 90% for all these catalysts via isopropanol catalytic conversion, revealing that each of the samples had a strong surface acidity. However, in the presence of O-2, 70%similar to 85% selectivity for acetone was obtained for TiO2 and ZrO2, suggesting that redox properties were predominant over acidity. Due to the formation of composite oxide, selectivity for propene increased to about 70%, whereas selectivity for acetone decreased to about 30%, indicating that the acidity was enhanced and the redox property was weakened.
Synergy of Ag and Interfacial Oxygen Vacancies on TiO 2 for Highly Efficient Photocatalytic Production of H 2 O 2

Yachao Wang,Lingfang Liu,Yaxiong Wei,Xinsheng Xu,Guofeng Zhao,Rui Zhong,Cong Fu

DOI: https://doi.org/10.1021/acsami.4c11426

IF: 9.5

2024-09-16

ACS Applied Materials & Interfaces

Abstract:Photocatalytic H(2)O(2) production stands as a promising sustainable technology for chemical synthesis. However, rapid charge recombination and limited oxygen adsorption by photocatalysts often limit its efficiency. Herein, we demonstrate that the synergy of Ag and interfacial oxygen vacancies on TiO(2) could overcome these challenges. The optimized Ag/TiO(2)-50 photocatalyst achieved an impressive H(2)O(2) production rate of 12.9 mmol h^(-1) g^(-1) and maintained a steady-state concentration of...

materials science, multidisciplinary,nanoscience & nanotechnology

TiO 2 with controllable oxygen vacancies for efficient isopropanol degradation: photoactivity and reaction mechanism

Progress in Photocatalytic Oxidation of Organic Contaminants Using TiO2 as the Catalyst

Rational Design of Nitrogen and Carbon Co-Decorated Mesoporous TiO2 Composites for Photocatalytic Selective Oxidation of Alcohols

Unraveling the Photocatalytic Mechanisms on TiO2 Surfaces Using the Oxygen-18 Isotopic Label Technique

Enhanced Photocatalytic Oxidation of Isopropanol by HKUST-1@TiO2 Core–Shell Structure with Ultrathin Anatase Porous Shell: Toxic Intermediate Control

Distribution And Concentration Of Surface Oxygen Vacancy Of Tio(2)And Its Photocatalytic Activity

Cu 2 O/SrTi 1- x Cr x O 3 Heterojunction Photocatalyst for the Efficient Degradation of Isopropanol under Visible Light Irradiation

Flame Synthesized Blue TiO 2− x with Tunable Oxygen Vacancies from Surface to Grain Boundary to Bulk

Promoting ring-opening efficiency for suppressing toxic intermediates during photocatalytic toluene degradation via surface oxygen vacancies

Kinetic pathways of sub-bandgap induced electron transfer in Ag/TiO2 and the effect on isopropanol dehydrogenation under gaseous conditions

The synergic removal mechanism for photothermocatalytic toluene over single-atom Pt/TiO 2 catalysts via flame spray pyrolysis

Design of TiO2-X nanotubes with controllable oxygen vacancy concentration and performance study of selective oxidation of benzyl alcohol

Wavelength-Dependent Activity of Oxygen Species in Propane Conversion on Rutile TiO2(110)

Competitive photooxidation of small colorless organics controlled by oxygen vacancies under visible light

Oxygen Vacancy-Governed Opposite Catalytic Performance for C3H6 and C3H8 Combustion: The Effect of the Pt Electronic Structure and Chemisorbed Oxygen Species

Photooxidation of Isoprene by Titanium Oxide Cluster Anions with Dimensions up to a Nanosize

Synthesis of Sandwich-Structured AgBr@Ag@TiO 2 Composite Photocatalyst and Study of Its Photocatalytic Performance for the Oxidation of Benzyl Alcohols to Benzaldehydes

Photothermal Propane Dehydrogenation Catalyzed by VO x -Doped TiO 2 Nanoparticles

Photocatalytic propylene epoxidation with O 2 over 4,4′-dibromobenzophenone modified carbon nitride coupled with TS-1

Characterization Of Tio2-Zro2 And Isopropanol Catalytic Conversion

Synergy of Ag and Interfacial Oxygen Vacancies on TiO 2 for Highly Efficient Photocatalytic Production of H 2 O 2