Abstract:3D printing technologies such as fused filament fabrication (FFF) offer great opportunities to enable the fabrication of complex geometries without access to a workshop or knowledge of machining. By adding filler materials to the raw filaments used for FFF, the material properties of the plastic can be adapted. With the addition of neutron absorbing particles, filaments can be created that enable 3D printing of neutron shielding with arbitrary geometry. Two materials for FFF are presented with different mixing ratios of hexagonal Boron nitride (h-BN) and Polylactic acid (PLA). BNPLA25 with 25 %wt h-BN and BNPLA35 with 35 %wt h-BN are compared to the commercially available Addbor N25 material. To qualify the applicability of BNPLA25 and BNPLA35 as shielding material for neutron instrumentation, such as neutron imaging, we investigated the overall neutron attenuation, the influence of non-optimized print settings, as well as characterized the incoherent neutron scattering and the microstructure using neutron imaging, and time-of-flight small-angle-neutron-scattering. Finally, the tensile strength of the material was determined in standardized tensile tests. The measured neutron attenuation shows excellent agreement with analytical calculations, thus validating both the material composition and the calculation method. Approximately 6 mm (8 mm) BNPLA35 are needed for transmission of a cold (thermal) neutron beam. Lack of extrusion due to suboptimal print settings can be compensated by increased thickness, clearly visible defects can be mitigated by 11–18% increase in thickness. Incoherent scattering is shown to be strongly reduced compared to pure PLA. The tensile strength of the material is shown not to be impacted by the h-BN filler. The good agreement between the measured attenuation and calculation, combined with the adoption of safety factor enables the quick and easy development as well as the performance estimation of shielding components. BNPLA is uniquely suited for 3D printing neutron shielding because of the combination of non-abrasive h-BN particles in standard PLA, which results in a filament that can be printed with almost any off-the-shelf printer and virtually no prior experience in 3D printing. This mitigates the slightly lower attenuation observed as compared to filaments containing , which is highly abrasive and requires extensive additive manufacturing experience.

Neutron moderation and manufacturing viability of 3D printed Acrylonitrile Butadiene Styrene spheres for use in neutron radiation detectors

3D Printing Neutron Detectors using Scintillating BN/ZnS Resin

A novel polystyrene-based scintillator production process involving additive manufacturing

Numerical Simulation of the Microtron Electron Beam Absorption by the Modified ABS-Plastic

A Novel, Rapid Response Renewable Biopolymer Neutron and Gamma Radiation Solid-State Detector for Dosimetry and Nuclear Reactor Flux-Power Mapping

A novel segmented-scintillator antineutrino detector

Siloxane-based 6LiF composites for flexible thermal neutron scintillation sensors with high efficiency: effects of 6LiF crystals size and dispersion homogeneity

BNPLA: borated plastic for 3D-printing of thermal and cold neutron shielding

Additive manufacturing of a 3D-segmented plastic scintillator detector for tracking and calorimetry of elementary particles

A Monte Carlo simulation of monoenergetic neutrons traversing rectangular and spherical polyethylene moderators

Additive manufacturing of fine-granularity optically-isolated plastic scintillator elements

Attenuation coefficient in the energy range 14-36 keV of 3D printing materials for physical breast phantoms

Mass spectrometric investigations into 3D printed parts to assess radiopurity as ultralow background materials for rare event physics detectors

Evaluation of Scintillator Detection Materials for Application within Airborne Environmental Radiation Monitoring

Research of 10BF3 Surrounded Plastic Scintillator As Fast Neutron Detector

A comparative study of 3D printing and sol-gel polymer production techniques: A case study on usage of ABS polymer for radiation shielding

3-D thermal and radiation-matter interaction simulations of a SiC solid-state detector for neutron flux measurements in JSI TRIGA Mark II research reactor

Mechanical Performance and Mesostructure Analysis of Proton-Irradiated Fused Filament Fabrication Acrylonitrile Butadiene Styrene Material

Lean-and-Green Fractional Factorial Screening of 3D-Printed ABS Mechanical Properties Using a Gibbs Sampler and a Neutrosophic Profiler

Acoustic modeling and performance evaluation of 3D-printed and metal differential photoacoustic sensors for trace gas detection

Improved manufacturing and performance of the dual-sided microstructured semiconductor neutron detector (DS-MSND)