Abstract:Introduction Reducing capital expenditure of polymer electrolyte membrane water electrolysis (PEMWE) is essential for reducing the production cost of green hydrogen. The amount of platinum group metal (PGM) loading significantly impacts the capital expenditure. Especially iridium catalyst and platinum coating on the porous transport layer of the anode have to be reduced. Our research group has developed the catalyst-integrated porous transport electrode (PTE), where iridium catalysts were directly deposited on porous transport layer (PTL) acting as an electronic conductive coating on the PTL 1 , 2 . This structure could reduce total PGM loading of PEMWE cells due to being virtually free of Pt coating on the PTL, typically 1 to 5 mg cm -2 3 . However, the catalyst-integrated PTE has an issue of the reduction of activation overvoltage in increasing iridium catalyst loading because the mass activity of iridium catalysts in the catalyst-integrated PTE decreases with increasing iridium loading. The hybrid anode consisting of both the conventional catalyst layer and the catalyst-integrated PTE as the PTL could reduce activation overvoltage effectively, and consequently the capital expenditure significantly with less Ir and Pt loadings. Experimental Titanium microfiber sheets with nominal porosity of ca. 70% (Nikko Techno, Ltd., Osaka, Japan) were used as the substrates acting as catalyst supports and PTLs. To increase the surface area of the titanium PTL, chemical etching with NaOH solution was performed. First, titanium sheets were etched in an aqueous 1 M NaOH solution at 60 °C for 1 h. After that, the etched titanium sheets were washed under ultra-sonication in 0.01M HNO 3 solution for 30 min and then washed in deionized water at room temperature for 10 min. Heat treatment was then performed at 400 °C in 5% H 2 -N 2 gas for 30 min. The catalyst-integrated PTE was prepared by depositing iridium onto the NaOH-etched titanium sheets via arc plasma deposition. Electrocatalyst paste for the PEMWE cathodes was prepared by dispersing the Pt/C (Pt 46.5 wt.%, TEC10E50E, Tanaka Kikinzoku Kogyo Co., Tokyo, Japan), 99.5% ethanol, deionized water, and 5% Nafion solution. IrO 2 electrocatalyst paste for the PEMWE anodes was prepared by dispersing the IrO 2 catalyst (IrO 2 (IV) TYPE II, Tokuriki Honten Co. Ltd., Tokyo, Japan), 99.5% ethanol, deionized water, and 5% Nafion solution. Using a spray printing system (Nordson, USA), these anode and cathode electrocatalyst pastes were spray-printed onto the electrolyte membrane (Nafion 212, E. I. du Pont de Nemours and Co., Wilmington, USA). The hybrid anodes were prepared by using the catalyst-integrated PTEs instead of Pt-coated PTLs. Results and discussion The conventional anode with 0.1 mg cm -2 of IrO 2 , the catalyst-integrated PTE with 0.344 mg cm -2 of Ir loading, and the hybrid anode consisting of this conventional IrO 2 -based catalyst and the catalyst-integrated PTE were prepared and evaluated. Figure 1 shows (a) I-V characteristics, (b) activation overvoltage, and (c) ohmic overvoltage of cells with three types of anodes. Figure 1(a) shows that the hybrid design is effective for significant performance improvement over the individual electrode design with the IrO 2 layer or the PTE. Electrolysis voltage of the cell with the hybrid anode at 10 A cm -2 was around 2.2 V. The activation overvoltage with the hybrid anode was lower than that with the conventional IrO 2 -based anode only and the catalyst-integrated PTE only, indicating that the iridium catalysts in the catalyst-integrated PTE are active even in the hybrid anode, as shown in Fig. 1(b). The ohmic overvoltage with the catalyst-integrated PTE was higher than that with the conventional anode, but the hybrid anode exhibited a comparable value to the conventional one. This may be because of the introduction of the intermediate catalyst layer consisting of ionomers and IrO 2 between the catalyst-integrated PTE and the electrolyte membrane, which is a mixed conductor of ions and electrons, especially reducing the proton transport resistance between the membrane and the PTE. Thus, hybrid anodes with catalyst-integrated electrodes instead of Pt-coated PTLs can potentially improve the performance of PEM electrolyzers and reduce the total PGM loading. References M. Yasutake, D. Kawachino, Z. Noda, J. Matsuda, K. Ito, A. Hayashi, and K. Sasaki, ECS Trans. , 92 (8), 833 (2019). M. Yasutake, D. Kawachino, Z. Noda, J. Matsuda, S. M. Lyth, K. Ito, A. Hayashi, and K. Sasaki, J. Electrochem. Soc. , 167 , 124523 (2020). The International Renewable Energy Agency, Green Hydrogen Cost Reduction , (2020). Figure 1

Hybrid Anode Design of Polymer Electrolyte Membrane Water Electrolysis Cells for Ultra-High Current Density Operation with Low Platinum Group Metal Loading

Hybrid Anode Design of Polymer Electrolyte Membrane Water Electrolysis for the Reduction of Total Platinum Group Metal Loading

(Invited) Lowering the Noble Metal Requirement for PEM Water Electrolysis: Membrane Electrode Assembly and Porous Transport Layer Design Considerations

Composite Anode for PEM Water Electrolyzers: Lowering Iridium Loadings and Reducing Material Costs with a Conductive Additive

Simultaneously Improving the Pore Structure and Electron Conductive Network of the Anode Catalyst Layer Via SnO2 Doping for Proton Exchange Membrane Water Electrolysis

Ionomer-free and recyclable porous-transport electrode for high-performing proton-exchange-membrane water electrolysis

High Performance AEM Water Electrolysis with PGM-Free Electrocatalysts

High Performance and Durable Anode with 10‐Fold Reduction of Iridium Loading for Proton Exchange Membrane Water Electrolysis

Pathways Toward Efficient and Durable Anion Exchange Membrane Water Electrolyzers Enabled By Electro‐Active Porous Transport Layers

Highly Porous Iridium Thin Electrodes with Low Loading and Improved Reaction Kinetics for Hydrogen Generation in PEM Electrolyzer Cells

Incorporation of PEDOT:PSS to Reduce Iridium Loading at Anode Catalyst Layer for Proton Exchange Membrane Water Electrolysis

Anion Exchange Ionomers Enable Sustained Pure-Water Electrolysis Using Platinum-Group-Metal-Free Electrocatalysts

Engineering the PEM Water Electrolysis Anode for Better Interfacial Electrical Conductivity

(Invited) PGM-Free Oer Catalysts for PEM Electrolyzer Application

One‐Step Fabrication of Ultralow Pt Loading High Efficiency Proton Exchange Membrane for Water Electrolysis by Conventional E‐Beam Metal Deposition

(Invited) Novel Design of Low-Loaded Membrane Electrode Assemblies for Advanced Low-Temperature Water Electrolyzers

Ultrathin Microporous Transport Layers: Implications for Low Catalyst Loadings, Thin Membranes, and High Current Density Operation for Proton Exchange Membrane Electrolysis

Design Focus of Anodes Toward High-Current-Density Low-Pt-Loading Proton Exchange Membrane Fuel Cells

Design of PEM water electrolysers with low iridium loading

Novel thin/tunable gas diffusion electrodes with ultra-low catalyst loading for hydrogen evolution reactions in proton exchange membrane electrolyzer cells

Influence of Microporous Layers on Interfacial Properties, Oxygen Flow Distribution, and Durability of Proton Exchange Membrane Water Electrolyzers