A highly efficient solid-state heat pump

Jaka Tušek

DOI: https://doi.org/10.1126/science.adl0804

IF: 56.9

2023-11-18

Science

Abstract:The high efficiency of a newly developed electrocaloric device brings theory closer to reality

multidisciplinary sciences

What problem does this paper attempt to address?

High cooling performance in a double-loop electrocaloric heat pump

Junning Li,Alvar Torelló,Veronika Kovacova,Uros Prah,Ashwath Aravindhan,Torsten Granzow,Tomoyasu Usui,Sakyo Hirose,Emmanuel Defay

DOI: https://doi.org/10.1126/science.adi5477

IF: 56.9

2023-11-18

Science

Abstract:Cooling through solid-state electrocaloric materials is an attractive replacement for vapor compression. Despite recent efforts, devices that are potentially commercially competitive have not been developed. We present an electrocaloric cooler with a maximum temperature span of 20.9 kelvin and a maximum cooling power of 4.2 watts under the moderate applied electric field of 10 volts per micrometer without any observed breakdown. Moreover, the maximum coefficient of performance, even taking into account energy expended on fluid pumping, reaches 64% of Carnot's efficiency as long as energy is properly recovered. We believe that this demonstration shows electrocaloric cooling to be a very promising alternative to vapor compression cooling.

multidisciplinary sciences
A Theoretical Study of an Innovative Ejector Enhanced Vapor Compression Heat Pump Cycle for Water Heating Application

Xiaojuan Chen,Yuanyuan Zhou,Jianlin Yu

DOI: https://doi.org/10.1016/j.enbuild.2011.08.037

IF: 7.201

2011-01-01

Energy and Buildings

Abstract:This study presents a novel vapor compression heat pump cycle in which an ejector associated with a subcooler is applied to enhance the heating performance for air-source heat pump water heater application. The heating coefficient of performance (COPh) and heating capacity of the novel cycle using the non-azeotropic mixture refrigerant R417A are theoretically investigated, for the ranges of evaporating temperature (−15 to 10°C) and condensing temperature (55–60°C). The theoretical results show that the COPh and volumetric heating capacity of the novel cycle are better than that of the conventional heat pump cycle. It is found that for the operating conditions considered, the maximum COPh and volumetric heating capacity can be improved by up to 1.62–6.92% and 15.20–37.32% over the conventional heat pump cycle, respectively. The performance characteristics of the novel cycle show its promise in air-source heat pump water heater applications.
Transient Performance of a Thermal Energy Storage-Based Heat Sink Using a Liquid Metal As the Phase Change Material

Li-Wu Fan,Yu-Yue Wu,Yu-Qi Xiao,Yi Zeng,Yi-Ling Zhang,Zi-Tao Yu

DOI: https://doi.org/10.1016/j.applthermaleng.2016.08.137

IF: 6.4

2016-01-01

Applied Thermal Engineering

Abstract:In this Technical Note, the use of a liquid metal, i.e., a low melting point Pb-Sn-In-Bi alloy, as the phase change material (PCM) in thermal energy storage-based heat sinks is tested in comparison to an organic PCM (1-octadecanol) having a similar melting point of similar to 60 degrees C. The thermophysical properties of the two types of PCM are characterized, revealing that the liquid metal is much more conductive while both have nearly identical volumetric latent heat of fusion (similar to 215 MJ/m(3)). By using at the same volume of 80 mL, i.e., the same energy storage capacity, the liquid metal is shown to outperform significantly over the organic PCM under the various heating powers up to 105.3 W/cm(2). During the heating period, the use of the liquid metal leads to a remarkable extension of the effective protection time to nearly twice longer as well as a reduction of the highest overheating temperature by up to 50 degrees C. The cool-down period can also be shortened significantly by taking advantage of the much higher thermal conductivity of the liquid metal. These findings suggest that liquid metals could serve as a promising PCM candidate for particular applications where the volume limit is very rigorous and the penalty in weight increment is acceptable. (C) 2016 Elsevier Ltd. All rights reserved.
Performance Study on an Electrocaloric Heat Pump Based on Ga-Based Liquid Metal

Panpan Song,Yawei Zhu,Zhongyan An,Mingshan Wei,Xiaoxia Sun,Yangjun Zhang

DOI: https://doi.org/10.3390/en16073104

IF: 3.2

2023-01-01

Energies

Abstract:A solid-state heat pump using the electrocaloric effect (ECE) provides a new idea for the future development of heat pumps. However, most of the electrocaloric (EC) heat pumps presented in the literature are low in efficiency and use at least one moving part, which significantly reduces the reliability of the heat pump and adds to its complexities. In this context, combining the positive and negative ECEs, we proposed a plate-laminar non-mobile EC heat pump adopting Gallium-based liquid metal as an intermediate medium to guarantee highly efficient heat transfer. Numerical simulation in COMSOL Multiphysics has been performed to investigate the correlation between different operating parameters and the performance of the EC heat pump. Changing the temperature span only, a COP of 8.13 and a UVHP of 746.1 W·dm−3 were obtained at a temperature span of 7 K. It was also found that the UVHP increased by 28.45% and COP increased by 25.46% after adding one layer of EC material. The electric-induced quantity of heat and cooling capacity was found to significantly affect the heating performance. The biggest heating power of 7132.7 W·dm−3 was obtained under 200 MV·m−1, and the biggest COP of 14.84 was obtained under 150 MV·m−1 at a cyclic period of 8 s. This study provides a highly efficient, non-mobile EC heat pump that employs fluid-thermal conjugated heat transfer, and exploration of the parameters makes the optimization of the heat pump possible by fine-tuning the operation parameters.
Theoretical Study of a Thermoelectric-Assisted Vapor Compression Cycle for Air-Source Heat Pump Applications

Lin Zhu,Jianlin Yu

DOI: https://doi.org/10.1016/j.ijrefrig.2014.12.001

2014-01-01

Abstract:This paper proposes a thermoelectric-assisted vapor compression cycle (TVCC) for applications in air-source heat pump systems which could enhance the heating capacity of the system. Performances of TVCC are calculated and then compared with that of basic vapor compression cycle (BVCC). The simulation results show that when coefficients of performance (COPs) of the two cycles are almost equal, the TVCC under maximum COP condition of the thermoelectric modules still performs better than BVCC by 13.0% in heating capacity through selecting the appropriate intermediate temperature. In addition, the TVCC can also achieve an improvement of 16.4%–21.7% in both the heating COP and capacity when compared with the BVCC with an assistant electric heater that is provided with the equivalent power input of thermoelectric heat exchanger. Thus, the TVCC could be beneficial to the applications in small heat pumps if there is always need for auxiliary electric heat.
Solid-state electrocaloric cooler controlled by a thermal switch

Pedro M. Resende,Florian Le Goupil,Guillaume Fleury,Georges Hadziioannou

DOI: https://doi.org/10.1103/physrevapplied.21.054021

IF: 4.6

2024-05-10

Physical Review Applied

Abstract:Refrigeration systems based on electrocaloric materials are considered as potential alternatives for the current vapor compression–based devices. These systems offer efficiencies closer to the Carnot limits, while also being compatible with miniaturization, compactness, and integration into electronics and wearables. Several prototypes have been proposed that mostly rely on mechanical and fluid motion for heat transfer, which prevent these systems from reaching higher operation frequency, good thermal contact, and low loss. Motionless electrocaloric solid-state devices have so far been conceptualized, but their relative complexity has hampered prototyping. In this work, we study the performance of a solid-state electrocaloric cooler that relies on thermoelectric switches to control heat flow. Our device operation mode minimizes energy consumption by absorbing heat passively through the heat switches. The applied currents, absorbed heat, power consumption, and coefficient of performance are assessed for a wide set of parameters following a steady-state heat propagation model, covering operation temperature, material properties, geometric features, frequency of operation, and material polarization losses. We show that a coefficient of performance (COP) above 1 can be obtained for temperature spans up to 6 K (for different material properties, geometry factors, or electrocaloric loss) and adiabatic temperature changes around 1 K higher than the applied temperature span. Higher temperature spans between 6 to 10 K yield a COP of the order of 0.1, leading to a significant increase in power consumption. These results are intended to guide research into these solid-state devices, in terms of choice of materials, temperatures, and geometry. https://doi.org/10.1103/PhysRevApplied.21.054021 © 2024 American Physical Society

physics, applied
A self-regenerative heat pump based on a dual-functional relaxor ferroelectric polymer

Hanxiang Wu,Yuan Zhu,Wenzhong Yan,Siyu Zhang,William Budiman,Kede Liu,Jianghan Wu,Yuan Meng,Xun Zhao,Ankur Mehta,Sumanjeet Kaur,Qibing Pei

DOI: https://doi.org/10.1126/science.adr2268

IF: 56.9

2024-11-01

Science

Abstract:Electrocaloric (EC) cooling presents a promising approach to efficient and compact solid-state heat pumps. However, reported EC coolers have complex architectures and limited cooling temperature lift. In this work, we introduce a self-regenerative heat pump (SRHP) using a cascade of EC polymer film stacks, which have electrostrictive actuations in response to an electric field that are directed to realize efficient heat transfer, eliminating the need for additional transportive or regenerative mechanisms. The SRHP demonstrates a cooling of 8.8 kelvin below ambient temperature in 30 seconds and delivers a maximum specific cooling power of 1.52 watts per gram. The temperature lift of the SRHP is 14.2 kelvin. These results underscore the potential of the compact solid-state cooling mechanism to address the increasing need for localized thermal management.

multidisciplinary sciences
Thermal Management: Electrostatic Actuating Double‐Unit Electrocaloric Cooling Device with High Efficiency (Adv. Energy Mater. 13/2021)

Yiwen Bo,Quan Zhang,Heng Cui,Mengyan Wang,Chunyang Zhang,Wen He,Xiangqian Fan,Yiwen Lv,Xiang Fu,Jiajie Liang,Yi Huang,Rujun Ma,Yongsheng Chen

DOI: https://doi.org/10.1002/aenm.202170049

IF: 27.8

2021-04-01

Advanced Energy Materials

Abstract:<p>In article number <a href="https://doi.org/10.1002/aenm.202003771">2003771</a>, Rujun Ma and co‐workers report a highly efficient double‐unit solid‐state refrigeration device based on two‐layer modified electrocaloric polymer stacks actuated by electrostatic forces. The availability and the high‐efficiency of the device for cooling the central processing unit provides a unique option for thermal management of microcircuits in the future. </p>

materials science, multidisciplinary,chemistry, physical,physics, applied, condensed matter,energy & fuels
Study on High Efficient Heat Recovery Cycle for Solid-State Cooling

Suxin Qian,Jiazhen Ling,Jan Muehlbauer,Yunho Hwang,Reinhard Radermacher

DOI: https://doi.org/10.1016/j.ijrefrig.2015.03.023

IF: 4.14

2015-01-01

International Journal of Refrigeration

Abstract:Traditional vapor compression cycles (VCCs) use mainly halogenated refrigerants such as hydrochloroflurocarbons and hydrofluorocarbons that are considered as greenhouse gases. Therefore, their regulations are imposed on a global scale. As an alternative cooling technology other than VCCs, solid-state cooling technologies, such as magnetic cooling, thermoelastic cooling and electrocaloric cooling, demonstrate its advantage of not using greenhouse gases as working fluids. However, one of the most challenging issues of these solid-state cooling technologies is the relative high parasitic internal latent heat loss, which could significantly deteriorate the system performance. In order to improve the system performance of solid-state cooling, the authors propose a novel and high-efficient heat recovery (HR) cycle for solid-state materials with high thermal conductivity. The novel heat recovery process was first compared as an analog of spatial scale counter-flow heat transfer process. A simplified ideal model was developed to quantitatively investigate the heat recovery process performance limit and the physics behind the analogy of the spatial scale counter-flow heat transfer process. Experiment was conducted and 60% HR efficiency was achieved. In addition, a detailed dynamic model validated by the experiment results was developed and used to further investigate the limiting factors together with the theoretical analysis. (C) 2015 Elsevier Ltd and IIR. All rights reserved.
Highly Efficient Electrocaloric Device Based on Composite Materials with Excellent Heat Transfer Performance

Qiang Li,Feihong Du,Donglin Han,XiaoShi Qian

DOI: https://doi.org/10.1088/1742-6596/2491/1/012016

2023-01-01

Journal of Physics Conference Series

Abstract:Abstract Electrocaloric (EC) cooling technology is known for its efficiency and simplicity of the electricity-driving method. However, there still are many challenges and problems, i.e., the poor heat transfer of EC materials (polymers), and the limited electrocaloric temperature change, which result in the limited cooling efficiency and/or cooling power of the EC cooling prototypes. The lack of EC device with high cooling performance poses challenging obstacles for the industrial deployment of the EC cooling technology. In this work, we demonstrated that the fabrication of P(VDF-TrFE-CFE) nanocomposites with BaZr0.2Ti0.8O3 (BZT) particles is an efficient way to improve the heat transfer of EC materials without compromising EC capability. In order to valid the positive effect of developing the EC device rather than provide a pure material study, we developed a solid-fluid coupling EC cooling machine numerically. The introduction of BZT composites allows EC refrigeration devices to exhibit a good COP while maintaining a relatively high total cooling power (>150 W) when the temperature span is 10 K. Therefore, the composites exhibit great potential of ECE for future cooling applications.
Present and future caloric refrigeration and heat-pump technologies

Andrej Kitanovski,Uroš Plaznik,Urban Tomc,Alojz Poredoš

DOI: https://doi.org/10.1016/j.ijrefrig.2015.06.008

IF: 4.14

2015-09-01

International Journal of Refrigeration

Abstract:In recent years, several emerging technologies in the domain of solid-state physics have been investigated as serious alternatives for future refrigeration, heat pumping, air conditioning, or even power generation applications. These technologies relate to what is called caloric energy conversion, i.e., barocalorics, electrocalorics, magnetocalorics, and elastocalorics. Of these technologies, the greatest progress has been observed in the domain of magnetic refrigeration. However, in the recent few years, significant research efforts have also been made in the field of electrocaloric and elastocaloric refrigeration. Many of these technologies suggest the possibility for improvements in energy efficiency, compactness, noise level, as well as a reduction in environmental impacts, so it seems very probable that they will start to fill particular market niches as a replacement for vapor-compression technology in the future.

engineering, mechanical,thermodynamics
Caloric Micro-cooling: Numerical modelling and parametric investigation

Jan Kalizan,Jaka Tušek

DOI: https://doi.org/10.48550/arXiv.2108.12164

2021-08-27

Applied Physics

Abstract:Cooling systems based on the caloric effects of ferroic materials show high potential for various cooling and heat-pumping applications due to their potentially high efficiencies and the lack of any environmentally hazardous refrigerants. One of such applications that has recently gained the attention of the scientific community is micro-cooling, which can be applied for hot-spot cooling and thermal management in electronic components. In this study a comprehensive numerical analysis of a caloric micro-cooling system using elastocaloric and electrocaloric materials was performed in order to investigate the limits and potential of this technology. We demonstrated that a caloric micro-cooling system is able to cool down the electronic component below room temperature or at least stabilize it at lower temperatures compared to the case when only the heat sink is applied in an efficient way (with the COP values exceeding 10). The specific cooling capacity of the caloric micro-cooling device strongly depends on the heat sink accompanied with the caloric material and its heat transfer capabilities. The caloric device can cool the electronic component below room temperature at heat-flux densities of up to 0.35 W/cm2 and up to 1 W/cm2 if it is used together with air-cooled heat sinks and water-cooled heat sinks, respectively. Caloric cooling systems could therefore play an important role as an efficient micro-cooling technology for certain applications, in particular where under-cooling below room temperature (low-temperature electronics) is required.
Performance Investigation on an Air Source Heat Pump System with Latent Heat Thermal Energy Storage

Ying Lin,Yubin Fan,Meng Yu,Long Jiang,Xuejun Zhang

DOI: https://doi.org/10.1016/j.energy.2021.121898

IF: 9

2022-01-01

Energy

Abstract:This paper proposes an air source heat pump (ASHP) system integrated with a latent heat thermal energy storage (LTES) unit based on a specially-designed heat exchanger, condensing heat storage unit, to further improve system performance in cold region. The innovation of this device is that heat is transferred directly between refrigerant and phase change material (PCM), which significantly reduces heat loss. Experimental investigation on thermal performance of the system is carried out. Besides, a mathematical model of condensing heat storage unit is developed to investigate charging/discharging characteristics and validated by experimental data. Experimental results show that heat storage capacity reaches 31.83 kWh and average heat release power is 4.73 kW. Simulation results indicate that both smaller fin pitch and larger fin thickness accelerate the melting rate of PCM, but variations of tube diameter show little impact on it. In order to maintain heat release power, circulating water flow rate should be increased with discharging time. Three-stage PCM improves both energy and exergy performance compared to single-stage PCM. COP improvement could reach 4.01% and overall exergy efficiency is increased by 4.65%. Therefore, ASHP system combined with LTES unit is a potential approach to expand its application under extremely low temperature. (c) 2021 Elsevier Ltd. All rights reserved.
Investigations of Cooling Efficiencies in Solid-State Electrocaloric Device

Rami Chukka,Santirajan Shannigrahi,Lang Chen

DOI: https://doi.org/10.1080/10584587.2012.660852

2012-01-01

Integrated Ferroelectrics

Abstract:Electrocaloric working elements are modeled by 2-D geometry and the thermodynamic efficiencies of Carnot, Ericsson and Brayton cycles were investigated in a solid-state electrocaloric cooling device. Using a comprehensive model for coupled thermal, electrical interactions in ferroelectric PMN-0.3PT single crystals, we demonstrated high Carnot efficiencies followed by Ericsson and Brayton cycles respectively. We also developed a physical model based on cascade systems to improve the device efficiency of Ericsson.
The numerical study on performance evaluation of a thermal switch capacitor in a magnetocaloric cooling device

Nada Petelin,Katja Vozel,Katja Klinar,Andrej Kitanovski

DOI: https://doi.org/10.1016/j.isci.2022.105517

IF: 5.8

2022-11-07

iScience

Abstract:Compact, solid thermal control devices offer a new way to control the intensity and direction of heat flow between the components of a system, which is crucial for both optimized performance and safety. In this work we study a thin, silicon thermal switch capacitor (TSC) used for heat transport in a magnetocaloric cooling system. A numerical model was developed to quantify the effects of various operating conditions and design parameters on the performance of a magnetocaloric device with an embedded TSC. Based on realistic material properties, a maximum cooling-power density of 4000 Wm-2 (2025 Wkg m c m - 1 ) was obtained for a zero temperature span and an operating frequency of 20 Hz. The use of the presented device was demonstrated on a battery system, motivating further experimental studies to develop a new, compact cooling device that can be directly attached to a heat reservoir, making it desirable for a variety of applications.
Performance Evaluation and Optimization of Air-to-Air Thermoelectric Heat Pump System

Je-Hyeong Bahk,Thiraj D. Mohankumar,Abhishek Saini,Sarah J. Watzman

2024-10-14

Abstract:Thermoelectric (TE) heat pumps are a promising solid-state technology for space cooling and heating owing to their unique advantages such as environmental friendliness with no harmful refrigerants, small form factors, low noise, robustness with no moving parts, and demand-flexible operation. However, their low coefficient of performance (COP) presents a challenge towards broader adaptation of the technology at the market level. Built on our previous theoretical framework for a modular system design aimed at improving both COP and cooling capacity, this study focuses on experimental characterization and optimization of a unit air-to-air TE heat pump system. We employ double-sided heating/cooling and counterflow configuration for uniform heat transfer with TE modules and heat exchangers. System-level evaluations validate the theoretical model and show the variation of air temperature change and system COP with different electric current inputs and air flowrates. A maximum cooling COP of 4.4 and a maximum heating COP of 6.0 were obtained at optimized current levels. Further analysis shows that parasitic thermal resistances in the system significantly reduced both COP and air temperature change by over 50%.

Applied Physics
Simulation of Chip-Size Electrocaloric Refrigerator with High Cooling-Power Density

Haiming Gu,Brent Craven,Xiaoshi Qian,Xinyu Li,Ailan Cheng,Q. M. Zhang

DOI: https://doi.org/10.1063/1.4796184

IF: 4

2013-01-01

Applied Physics Letters

Abstract:The large electrocaloric effect that found in ferroelectric polymers creates unique opportunity for developing high performance chip scale solid state refrigerator. This letter presents a finite volume simulation study and shows that by employing solid state regenerators and the micro-heat pumping mechanism used in the thermoacoustic cooling, a compact Electrocaloric Oscillatory Refrigeration (ECOR) device can be realized. The simulation results demonstrate that a 1 cm-long ECOR device can provide 9 W/cm3 volumetric cooling power density at 20 K temperature span. By tuning the device parameters in the model, the ECOR can reach more than 50% of the Carnot efficiency.
Superconducting Spintronic Heat Engine

Clodoaldo I. L. de Araujo,Pauli Virtanen,Maria Spies,Carmen González-Orellana,Samuel Kerschbaumer,Maxim Ilyn,Celia Rogero,Tero T. Heikkilä,Francesco Giazotto,E. Strambini

2023-10-27

Abstract:Heat engines are key devices that convert thermal energy into usable energy. Strong thermoelectricity, at the basis of electrical heat engines, is present in superconducting spin tunnel barriers at cryogenic temperatures where conventional semiconducting or metallic technologies cease to work. Here we realize a superconducting spintronic heat engine consisting of a ferromagnetic insulator/superconductor/insulator/ferromagnet tunnel junction (EuS/Al/AlO$_x$/Co). The efficiency of the engine is quantified for bath temperatures ranging from 25 mK up to 800 mK, and at different load resistances. Moreover, we show that the sign of the generated thermoelectric voltage can be inverted according to the parallel or anti-parallel orientation of the two ferromagnetic layers, EuS and Co. This realizes a thermoelectric spin valve controlling the sign and strength of the Seebeck coefficient, thereby implementing a thermoelectric memory cell. We propose a theoretical model that allows describing the experimental data and predicts the engine efficiency for different device parameters.

Mesoscale and Nanoscale Physics,Superconductivity
A Chip Scale Electrocaloric Effect Based Cooling Device

Haiming Gu,Xiaoshi Qian,Xinyu Li,Brent Craven,Wenyi Zhu,Ailan Cheng,S. C. Yao,Q. M. Zhang

DOI: https://doi.org/10.1063/1.4799283

IF: 4

2013-01-01

Applied Physics Letters

Abstract:The recent finding of large electrocaloric effect in several ferroelectric polymers creates unique opportunity for developing compact size solid state cooling cycles beyond the traditional mechanical vapor compression cycles. Here, we show that, by employing regeneration process with solid state regenerators, a chip scale Electrocaloric Oscillatory Refrigeration (ECOR) can be realized. A prototype ECOR is fabricated and characterized. More than 6 K temperature span is obtained near room temperature between the hot and cold sides of a 2 cm long device. Finite volume simulation validates the test results and shows the potential high performance of the ECOR.
Concept Design And Numerical Evaluation Of A Highly Efficient Rotary Electrocaloric Refrigeration Device

Qiang Li,Junye Shi,Donglin Han,Feihong Du,Jiangping Chen,Xiaoshi Qian

DOI: https://doi.org/10.1016/j.applthermaleng.2021.116806

IF: 6.4

2021-01-01

Applied Thermal Engineering

Abstract:Enabled by the discovery of giant electrocaloric effect (ECE) in inorganic ceramics and organic polymers, Electrocaloric (EC) cooling technology has attracted considerable attention from both academia and industrial. However, there remains many challenges in the refrigeration efficiency and/or capacity of the currently reported electrocaloric refrigeration devices. In this work, we propose a concept design of EC refrigeration device, in which the working bodies are rotating in a plane perpendicular to the direction of fluid flow. The rotary EC device adopting heat transfer fluid as an intermediate medium allows for improved heat exchange between EC materials and outside environment, and efficiently delivers cooling effects to where it's needed. Simulations have been performed to investigate the system cooling performance under different operating strategies. Meanwhile, comparative researches on different heat transfer fluid are conducted and the corresponding cooling effects are studied. When using deionized water as heat transfer medium, the system can achieve a cooling power density of 9.89 Wcm(-3) and COP of 10.48 over 10 K temperature span. In general, this work provides a highly-efficient rotary EC refrigeration device concept that employs fluid-solid conjugated heat transfer, and guides the optimization of operating strategy and selection of heat transfer fluid.

A highly efficient solid-state heat pump

High cooling performance in a double-loop electrocaloric heat pump

A Theoretical Study of an Innovative Ejector Enhanced Vapor Compression Heat Pump Cycle for Water Heating Application

Transient Performance of a Thermal Energy Storage-Based Heat Sink Using a Liquid Metal As the Phase Change Material

Performance Study on an Electrocaloric Heat Pump Based on Ga-Based Liquid Metal

Theoretical Study of a Thermoelectric-Assisted Vapor Compression Cycle for Air-Source Heat Pump Applications

Solid-state electrocaloric cooler controlled by a thermal switch

A self-regenerative heat pump based on a dual-functional relaxor ferroelectric polymer

Thermal Management: Electrostatic Actuating Double‐Unit Electrocaloric Cooling Device with High Efficiency (Adv. Energy Mater. 13/2021)

Study on High Efficient Heat Recovery Cycle for Solid-State Cooling

Highly Efficient Electrocaloric Device Based on Composite Materials with Excellent Heat Transfer Performance

Present and future caloric refrigeration and heat-pump technologies

Caloric Micro-cooling: Numerical modelling and parametric investigation

Performance Investigation on an Air Source Heat Pump System with Latent Heat Thermal Energy Storage

Investigations of Cooling Efficiencies in Solid-State Electrocaloric Device

The numerical study on performance evaluation of a thermal switch capacitor in a magnetocaloric cooling device

Performance Evaluation and Optimization of Air-to-Air Thermoelectric Heat Pump System

Simulation of Chip-Size Electrocaloric Refrigerator with High Cooling-Power Density

Superconducting Spintronic Heat Engine

A Chip Scale Electrocaloric Effect Based Cooling Device

Concept Design And Numerical Evaluation Of A Highly Efficient Rotary Electrocaloric Refrigeration Device