Abstract:The aim of the study was to investigate the effect of different repair procedures on the repair bond strength of bulk-fill and nanohybrid resin composites after different aging periods. The resin composite blocks (8 × 8 × 4 mm3) were prepared from a bulk-fill (reliaFIL Bulk) and a nanohybrid (reliaFIL LC) resin composite and grouped according to aging duration (6 months, 1 year, and 2 years). Following aging, the blocks were assigned to different surface treatments; air-abrasion with aluminum oxide powder, roughening with a diamond bur, and no treatment. After cleansing with phosphoric acid, a silane layer (Porcelain Primer) was applied on the surface of half of the specimens in each group. The specimens were subdivided into two groups (n = 5): Scotchbond Universal (3M Oral Care) and All-Bond Universal (Bisco). The blocks were repaired with the nanohybrid composite (8 × 8 × 8 mm 3). The repaired specimens were stored in distilled water (37 °C/24 h) and segmented into beams. Half of the beams were immediately subjected to microtensile μTBS testing (1 mm/min), while the other half was stored in distilled water (37 °C) for 6 months before testing. Failure modes were analyzed using stereomicroscope and SEM. Statistical analyses were performed with ANOVA and least significant difference tests (LSD) tests (p = 0.05). The extension of aging periods (6 months, 1 year, and 2 years) reduced the repair bond strength in some groups for both resin composites (p < 0.05). The air-abrasion and bur roughening improved the repair bond strength (p < 0.05). The silane application did not influence the repair bond strength and durability (p > 0.05). There was no difference among the universal adhesives in the same surface treatment groups (p > 0.05). The mechanical roughening treatments are necessary for the repair of resin composite. The universal adhesives might be used for the repair of resin composites regardless of silane content without prior silane application.

A comparative study on adhesive properties of nanoparticle reinforced epoxy bonded single-strap repaired composites

Investigation failure behaviours of notched composite plates repaired with using adhesive and patch

Investigation of patch application failure behaviors according to fiber orientation difference at notched composite plates

Failure analysis of the patch repaired E-glass chopped fiber strand mat/epoxy composites

Nano-hybridization effects of nano-silica and nano-graphene platelet on mechanical properties of E-glass/epoxy nanocomposites

Finite element analysis of load-carrying capacity of single lap joints bonded with epoxy/nanoalumina adhesives

Investigation of mechanical properties of nano hexagonal boron nitride integrated epoxy adhesives in bonded GFRP and CFRP composite joints

The Effect of Patch Geometry on the Static and Fatigue Behaviors of Defective Aluminum Panels Repaired with A Composite Patch

Investigation of the mechanical and thermal properties of epoxy adhesives reinforced by carbon nanotubes and silicon dioxide nanoparticles in single-lap joints

Effect of composite to aluminum single lap joints reinforced with graphene doped nylon 6.6 nanofibers

Study of tensile‐tensile fatigue behavior of patch repaired carbon‐glass hybrid composite

The Effect of Nanoparticles on the Adhesion of Epoxy Adhesive

Mechanical Characterization of Hybrid Nano-Filled Glass/Epoxy Composites

Experimental study of the influence of adhesive reinforcement in lap joints for composite structures subjected to mechanical loads

Mode-I and II fracture behavior of metal-to-composite bonded interfaces with a graphene nanoplatelet-reinforced structural epoxy adhesive

Comparison of Repair Methods for Cracked Titanium Alloy Aircraft Structures with Single-Sided Adhesively Bonded Composite Patches

Advanced adhesive repairs and reinforcements for curved glass/epoxy composite laminates

Comparative fracture surface analysis of adhesively bonded dissimilar lap joints: Nanosilica effect

Mechanical properties of UV‐curable carbon fiber‐reinforced polymer composite patch: Repair evaluation of damaged aluminum alloy

Repair of Bulk-Fill and Nanohybrid Resin Composites: Effect of Surface Conditioning, Adhesive Promoters, and Long-Term Aging

Mechanical and low velocity impact behaviour of intra-ply glass/kevlar fibre reinforced nano-silica and micro-rubber modified epoxy resin hybrid composite