Abstract:Architected metallic materials generally suffer from a serious engineering problem of mechanical instability manifested as the emergence of localized deformation bands and collapse of strength. They usually cannot exhibit satisfactory shape recoverability due to the little recoverable strain of metallic constituent material. After yielding, the metallic constituent material usually exhibits a continuous low strain-hardening capacity, giving the local yielded regions of architecture low load resistance and easily developing into excessive deformation bands, accompanied by the collapse of strength. Here, a novel constituent material deformation design strategy has been skillfully proposed, where the low load resistance of yielded regions of the architecture can be effectively compensated by the significant self-strengthening behavior of constituent material, thus avoiding the formation of localized deformation bands and collapse of strength. To substantiate this strategy, shape-memory alloys (SMAs) are considered as suitable constituent materials for possessing both self-strengthening behavior and shape-recovery function. A 3D-printing technique was adopted to prepare various NiTi SMA architected materials with different geometric structures. It is demonstrated that all of these architected metallic materials can be stably and uniformly compressed by up to 80% without the formation of localized bands, collapse of strength, and structural failure, exhibiting ultrahigh damage tolerance. Furthermore, these SMA architected materials can display more than 98% shape recovery even after 80% deformation and excellent cycle stability during 15 cycles. This work exploits the amazing impact of constituent materials on constructing supernormal properties of architected materials and will open new avenues for developing high-performance architected metallic materials.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsami.1c11226.Typical secondary hardening behavior of commercial NiTi SMA, stripe rotation scanning strategy used for 3D-printing, preparation procedure of 3D-printed NiTi tensile samples, XRD spectrum of 3D-printed NiTi alloy, comparison of the tensile properties of 3D-printed NiTi and machined NiTi alloy, tensile stress–strain curves of three different constituent materials, compression deformation behavior of the 3D-printed Al honeycomb, compression deformation behavior of the 3D-printed NiTi multicell honeycomb, compression deformation behavior of the machined Al honeycomb, finite element simulation results, deformation of the representative unit cell, and shape-recovery rates of the NiTi re-entrant negative Poisson ratio structure and octahedral lattice structure (PDF)Compressive deformation comparison of 3D-printed NiTi honeycomb and machined Al honeycomb (MP4)Shape recovery of a 3D-printed NiTi honeycomb upon heating (MP4)This article has not yet been cited by other publications.

Investigation on the Mechanical Properties and Shape Memory Effect of Landing Buffer Structure Based on NiTi Alloy Printing

Study on Impact Energy Absorption and Adhesion of Biomimetic Buffer System for Space Robots

Shock-Resistant and Energy-Absorbing Properties of Bionic NiTi Lattice Structure Manufactured by SLM

Energy Absorption Behaviors of a Novel Buffer Lander-Leg with Yoshimura Core

Soft-Landing Dynamic Analysis of a Manned Lunar Lander Em-Ploying Energy Absorption Materials of Carbon Nanotube Buckypaper

Study on the Mechanical Properties of Bionic Protection and Self-Recovery Structures

Laser powder bed fusion additive manufacturing of NiTi shape memory alloys: A review

A Humanoid Robot Foot with a Lattice Structure for Absorbing Ground Impact Forces

Mechanical and shape memory properties of NiTi triply periodic minimal surface structures fabricated by laser powder bed fusion

Mechanical analysis characteristics of bionic structure based on NiTi alloy additive manufacturing

Research on Impact Process of Lander Footpad Against Simulant Lunar Soils

Bioinspired design of a landing system with soft shock absorbers for autonomous aerial robots

Bionic Design Method of a Non-Uniform Lattice Structure for a Landing Footpad

Time-varying deposition strategy for comprehensive properties improvement of bionic bidirectional gradient NiTi alloy fabricated by laser directed energy deposition

Effect of Structural Configurations on Mechanical and Shape Recovery Properties of NiTi Triply Periodic Minimal Surface Porous Structures

Volume Fraction Effect on the Mechanical and Shape Memory Properties of NiTi Gyroid Lattice Structure Fabricated by Laser Powder Bed Fusion

3D-Printing Damage-Tolerant Architected Metallic Materials with Shape Recoverability via Special Deformation Design of Constituent Material

Solidification characterization and its correlation with the mechanical properties and functional response of NiTi shape memory alloy manufactured by electron beam freeform fabrication

Optimization Design of the Inner Structure for a Bioinspired Heel Pad with Distinct Cushioning Property

Laser powder bed fusion of nitinol shape memory alloy with superelastic characteristics on Ti substrate

Selective laser melting fabrication of body-temperature shape memory NiTi alloy for 4D-printed orthopedic implants