Abstract:The properties of lightweight, high strength, better corrosion resistance, high electrical conductivity, etc. made aluminium alloys one of the favorite materials for industrial purposes. The aerospace, marine, automobile and railway industries use these alloys very commonly. But the lower melting temperature, high thermal conductivity and unusual grain growth make it difficult to weld material. So solid-state welding process named friction stir welding (FSW) is used for higher welding joint efficiencies for these alloys. The performance of FSWed joints directly depends upon the levels of input parameters used for the welding process. The present study is an attempt to optimize the process parameters for FSW of armor-grade aluminium alloys AA5083. Tool design parameters (Shoulder Diameter, Shoulder Flatness and Pin Profile) along with machine parameters (welding speed) are used for variation to analyze their effects on the quality of the joints. The experiments were designed by the response surface methodology and the significance of these parameters was analyzed by ANOVA. Where all four considered parameters were found significantly affect the responses i.e. ultimate tensile strength, yield tensile strength and elongation. An optimized set of parameters was revealed by Desirability a multi-objective optimization approach. “Desirability” suggests 18.5 mm shoulder diameter, 2.0 mm shoulder flatness, square pin profile and 48.9 mm/min welding speed as a set of optimized parameters. The 77.9% joint efficiency can be achieved at the mentioned optimized parameters. To analyze the relationships between variation in responses with the variation in process parameters and the microstructure of the welded joints the microstructure analysis has been conducted. The microstructural analysis revealed that high heat input causes an unwanted grain growth in the heat-affected zone and the lower heat input causes an insufficient temperature for the softening of the material in the nugget zone.

Multi objective Optimizations of friction stir welding process parameters for reinforcement of copper particles in aluminum alloy using Taguchi based grey relational analysis (GRA) and ANOVA.

Optimization of Dissimilar AA5052 and AA2219 Alloy Joints in Friction Stir Welding Using Taguchi Grey Relational Analysis

Multiobjective Optimization of Friction Stir Welding Process Parameters on Aluminum Alloy AA 5083 Using Taguchi-Based Grey Relation Analysis

Optimization and Characterization Studies of Dissimilar Friction Stir Welding Parameters of Brass and Aluminum Alloy 6063 Using Taguchi

Investigations and optimization of friction stir welding process to improve microstructures of aluminum alloys

Optimization of process parameters of friction stir welded joints of dissimilar aluminum alloy by response surface methodology

Multi-objective Optimization of FSW Process Parameters of Aluminium Alloy Using Taguchi-Based Grey Relational Analysis

Experimental investigation and optimization of mechanical properties on combination of higher and lower strength of aluminum alloys

Multi-objective optimization of FSW variables on joint properties of AA5754 aluminum alloy using Taguchi approach and grey relational analysis

Optimization of the Process Parameters of Dissimilar Welded Joints in FSSW Welding Process of Aluminum Alloy with Copper Alloy Using Taguchi Optimization Technique

Grey-Taguchi Approach for Optimizing FSW Parameters in Joining AA6262 and AA5083 Alloys

Optimization of process parameters in friction stir welding of dissimilar aluminum alloys (AA6061–T6 and AA5052–H32)

Optimization of Friction Stir Welded Dissimilar Aluminum Alloys EN AW-5083-H111 and EN AW-6082-T651 using Hybrid Taguchi-Based Grey Relation Analysis

Mathematical modeling and optimization of friction stir welding process parameters for armor-grade aluminium alloy

Parameters Optimization of Dissimilar Friction Stir Welding for AA7079 and AA8050 through RSM

Modeling and Optimization of Friction Stir Welding Parameters for Joining Dissimilar Aluminum Alloys

Optimization of Process Parameters for Friction Stir Welding of Aluminum and Copper Using the Taguchi Method

Optimization of process parameters of aluminum alloy AA 2014-T6 friction stir welds by response surface methodology

A multi-objective optimization of the friction stir welding process using RSM-based-desirability function approach for joining aluminum alloy 6063-T6 pipes

Effects of multi-objective optimization of friction stir welding process parameter on mechanical and ballistic properties of AA5754 aluminum alloy

Optimizing Friction Stir Welding of Dissimilar Grades of Aluminum Alloy Using WASPAS