Abstract:It is theoretical basis for harvest machinery selection to discuss technology productivity changing with plot conditions, which are plot area, length, width and so on under the condition of land managing scales over the wide range. Harvesting operation is one of the key processes of grain production, and choosing the appropriate harvesting machine is a vital step to reap the grain with larger technology productivity. A lot of researches on agricultural mechanization selection have been done by both domestic and foreign experts. It has been found that there are existing methods for agricultural machine selection such as fuzzy clustering comprehensive evaluation method, linear programming, and mixed integer linear programming. In these methods, the economic performance of the agricultural machinery unit is the objective considered in most cases. But the technical performances of agricultural machinery units, such as the practical productivity, are usually neglected. Plot conditions, including plot area, length, width, and distance between plots, are not considered in the methods, but they are important factors influencing the technology productivity of agricultural machineries. At the same time, it has also been found that the power of most agricultural machineries does not match the plot conditions in the practice of agricultural production. In this paper, the mathematic models calculating every kind of time consumption item during combined operation, including working time, turning time, preparation time before unloading, unloading time, preparation time after unloading and transferring time between plots, were established. On the basis of that, the mathematic models for calculating the combines’ technology productivity under the condition of different unloading ways were also set up. These mathematic models contain the variables such as plot area, length, width and distance between plots, and reveal the regularities of technology productivities changing with plot conditions. Experiment was designed according to the method of tracing the practical operating process. Taking 8 kinds of typical combines for harvesting soybean as experiment objectives, the values of all kinds of time consumption items were tested under the condition of fixed distance during the process of normal harvesting operation after enough experiments were executed. All the data of time consumption items were checked using the normal distribution models and the error data were removed according to the 3-Sigma principle. The mathematic models of time consumption items and combine technology productivity established were proved to be correct by the experiments and the actual operating status. According to the models and tested data, the technology productivities of 8 kinds of combine harvesters changing with plot conditions were calculated after the MATLAB program was designed and executed. Curve groups of technology productivity of each kind of combine changing with plot conditions were drew out using the EXCEL. Thus, the quantitative regularity of technology productivity of combine changing with plot conditions was revealed. According to the regularity, the technology productivity became larger as the value of plot area and length became bigger, but the changing velocity of technology productivity became slow after a specific values of plot area and length. The technology productivity of combine with the header width of 2-3 m was higher when the plot area was more than 3 hm2 and the length was more than 400 m. For the combines with the header width of 4-5 m, the technology productivity was higher when the plot area was more than 5 hm2 and the length was more than 600 m. The technology productivity of combine with the header width more than 7 m was higher when the plot area was more than 7 hm2 and the length was more than 800 m. The results of the paper can provide the direct theoretical guidance for practical combine selection under the status of land managing scale with large range, and they are also the improvement and supplement for the theory of agricultural machinery selection.

On the rational choice of a combine harvester and a reaper for grain harvesting in conditions of Siberia

Analyticity of complex criteria for evaluation of grain production in agricultural enterprises intensification of engineering management

OPTIMIZATION MODELING ANALYSIS FOR GRAIN HARVESTING MANAGEMENT

RESEARCH ON THE INFLUENCE OF THE OPERATING MODES OF COMBINE HARVESTER’S TRANSPORTATION LINES ON THE QUALITY OF GRAIN THRESHING

Development of a methodology for choosing conditions of interaction between harvesting and transport complexes

Increase in grain combine harvester performance and in quality of harvesting grain crops

MANAGEMENT OF THE COST MECHANISM OF INNOVATION PROCESSES TILLAGE FOR ADAPTIVE-LANDSCAPE AGRICULTURE IN SIBERIA

Harmonization of investment and operational costs of the grain industry in the light of the theory of sustainable development

Variation of Technology Productivity of Harvesting Outfit along with Site Conditions

Quantification of the Climate Change Impact on the Grain Production in the South of Siberia

Optimization of the production of varieties of grain crops using a satellite navigation system in the forest-steppe of the Priobye region

Change of Technical Condition and Productivity of Grain Harvesters Depending on Term of Operation

Comparative evaluation of seeding spring wheat methods when using different types of coulters

Experimental Studies of the Seed-Sowing Device for the Grain Seeder SUBM-3.6

Optimization of the harvesting and transport complex work in forage conservation

Results of Industrial Application of a Combine Harvester When Unloading Grain at the Edge of the Field

Model, algorithm and computer application for automated selection of varieties and hybrids of grain crops

ROTARY REPLACEMENT OF SAW CHAINS AS A WAY TO INCREASE HARVESTER PRODUCTIVITY

MODELING TRACTOR PARAMETERS AND TILLAGE UNITCONFIGURATION TAKINGINTO ACCOUNT THE INFLUENCE OF NATURAL AND PRODUCTION FACTORS

Application of machine learning methods for crop rotation selection in organic farming system

Combine harvester productivity calculation model and analysis of suitable operation route