Abstract:The current thermocatalytic acetylene hydrogenation process suffers from the use of excessive hydrogen and the noble metal Pd, high temperatures and overhydrogenation. Here we report an electrocatalytic semihydrogenation strategy to selectively reduce acetylene impurities to ethylene under ambient conditions. For a crude ethylene flow that contains 1 × 104 ppm acetylene, electrochemically deposited Cu dendrites exhibited a high specific selectivity of 97%, continuous production of a polymer-grade ethylene stream (4 ppm acetylene) at a large space velocity of 9.6 × 104 ml gcat–1 h–1 and excellent long-term stability. Theoretical and operando electrochemical Raman investigations revealed that the outstanding electrocatalytic acetylene semihydrogenation performance of Cu catalysts originates from its exothermic acetylene adsorption and ethylene desorption. Meanwhile, the electrocatalytic semihydrogenation strategy is universally applicable for hydrogenating other alkyne impurities to produce polymer-grade olefins, for example, propylene and 1,3-butadiene.

What problem does this paper attempt to address?

The paper aims to address the issue of acetylene impurities in the production of ethylene. Traditionally, ethylene is produced globally in the petroleum industry through hydrocarbon steam cracking, and this ethylene stream inevitably contains about 0.5–3% acetylene impurities (approximately 5 × 10^3–3 × 10^4 ppm). These impurities can rapidly poison catalysts (such as Ziegler-Natta catalysts) during polymerization, significantly reducing the quality of the target polymer. To meet the stringent polymer-grade ethylene standards, the acetylene impurity content must be below 5 ppm. Current industrial technologies and laboratory research mainly focus on the thermal catalytic hydrogenation of acetylene, but this method has several major drawbacks: first, it requires a large amount of hydrogen as a hydrogen source, which poses a serious explosion risk and may lead to partial hydrogenation of ethylene, producing ethane impurities; second, high temperatures (100–250°C) are used to decompose hydrogen and activate acetylene, resulting in high energy consumption and uncontrollable over-hydrogenation of ethylene; finally, expensive palladium-based catalysts are required for acetylene hydrogenation. Therefore, there is an urgent need for an environmentally friendly and cost-effective semi-hydrogenation method to continuously produce polymer-grade ethylene feedstock. The paper proposes a selective electrocatalytic semi-hydrogenation method for acetylene, which can be carried out at room temperature and atmospheric pressure, using water as the hydrogen source, thus avoiding the use of excess hydrogen. The research team developed a copper electrocatalyst that achieves selective electrocatalytic semi-hydrogenation of acetylene impurities at the three-phase interface in a flow cell. This method not only demonstrates excellent performance in practical applications but also has high stability and space velocity, making it a promising alternative to traditional thermal catalytic hydrogenation methods. Additionally, this electrocatalytic semi-hydrogenation strategy can be widely applied to the hydrogenation of other alkyne impurities to produce polymer-grade olefins, such as propylene and 1,3-butadiene.

Selective electrocatalytic semihydrogenation of acetylene impurities for the production of polymer-grade ethylene

Electrosynthesis of Polymer-Grade Ethylene Via Acetylene Semihydrogenation over Undercoordinated Cu Nanodots

Cu Single‐Atom Catalysts for High‐Selectivity Electrocatalytic Acetylene Semihydrogenation

Room-temperature electrochemical acetylene reduction to ethylene with high conversion and selectivity

Hydrophobic Surface Modification of Cu-Based Catalysts for Enhanced Semihydrogenation of Acetylene in Excess Ethylene

Titania‐supported Cu Single Atom Catalyst for Electrochemical Reduction of Acetylene to Ethylene at Low‐Concentrations with Suppressed Hydrogen Evolution

Near 100% Conversion of Acetylene to High‐purity Ethylene at Ampere‐Level Current

Highly efficient ethylene production via electrocatalytic hydrogenation of acetylene under mild conditions

Highly Active Isolated Single-Atom Pd Catalyst Supported on Layered MgO for Semihydrogenation of Acetylene

Identification of Copper as an Ideal Catalyst for Electrochemical Alkyne Semi-hydrogenation

Efficient Industrial-Current-density Acetylene to Polymer-Grade Ethylene Via Hydrogen-Localization Transfer over Fluorine-Modified Copper

Highly Efficient and Selective Electrocatalytic Semihydrogenation of Acetylene to Ethylene via Continuous Proton Feeding and Accelerated Transfer on Cu NP/FeNC Composite

Catalyst Design for Acetylene Semi-Hydrogenation

Decoupling Active Sites Enables Low-Temperature Semihydrogenation of Acetylene

Selective Catalytic Conversion of Acetylene to Ethylene Powered by Water and Visible Light

Photocatalytic Semi-Hydrogenation of Acetylene to Polymer-Grade Ethylene with Molecular and Metal-Organic Framework Cobaloximes

Hydroxyl group modification improves the selectivity of metal single atom on poly(heptazine imide) for electrocatalytic acetylene semi-hydrogenation

Alloyed PdCu Nanoparticles Within Siliceous Zeolite Crystals for Catalytic Semihydrogenation

Acetylene-Selective Hydrogenation Catalyzed By Cationic Confined In Zeolite

Copper-Based Catalysts for Selective Hydrogenation of Acetylene Derived from Cu(OH) 2

Fully Exposed Nickel Clusters for Semihydrogenation of Acetylene