Abstract:AbstractSteam assisted gravity drainage (SAGD) is recognized as a profitable and stable approach to address the exploitation of heavy oil and oil sand resources. However, the efficiency of SAGD, a close relative of a sufficiently-expanded and uniformly-developed steam chamber, tends to be deteriorated by quick steam movement and high heterogeneity. Chemical additives and foam assisted SAGD (CAFA-SAGD) is a strategy proposed on this account. This study aims to analyze the mechanisms and phenomena involved.The injection of chemical additives to promote in-situ foam generation reduces gas relative permeability by slow-moving and stagnant bubbles trapping. Also, lamella resists bubbles flow and increases apparent gas viscosity. The restriction of steam mobility thus favors a sufficiently-expanded steam chamber and the nitrogen co-injected to stabilize bubbles works as a separator between steam and overburden to reduce heat loss. Simultaneously, the interfacial tension reduction due to surfactants injection at a water/oil interface may influence phase behavior, which further leads to the solubilisation of residual oil. CAFA-SAGD is thus likely to increase heat efficiency and add oil output.A homogeneous model is built to analyze CAFA-SAGD considering foam generation by snap-off and leave-behind, foam trapping in a porous medium and foam coalescence due to both the lack of surfactants and capillary suction. Besides, with the analysis of foam wall slip phenomena, a comprehensive foam property model is coupled to analyze shear thinning rheology and calculate lamella viscosity as a function of gas saturation and gas velocity. In addition, the influences generated by surfactant injection should be added. This study also develops an analytical FA-SAGD model based on Butler's finger rising model (1987) to show foam's effects on a steam chamber growth rate and shape. We derive the FA-SAGD model accounting for the retarded steam movement with higher steam viscosity and lower gas relative permeability. The foam viscosity is calculated as a function of gas saturation and a gas rate, and the modification of gas relative permeability is reflected with a higher gas residual saturation according to Bertin et al.'s foam property model (1998). After comparing, validating, and discussing the developed model against the SAGD model, we find that foam injection contributes to high production efficiency with less steam consumption. A lower steam mobility generated by stronger foam is more likely to have a lower SOR (steam-oil ratio).The results agree well with the published high-temperature steam foam experiments and pilot tests. Strong bubbles accumulate along the boundary of a steam chamber to restrict steam movement, while weak foam fills inside the chamber to enhance steam trap, contributing to a higher oil recovery factor and lower SOR.

Characteristics and Stabilization Mechanism of Three-Phase Foam: Improving Heavy Oil Recovery via Steam Stimulation through Two-Dimensional Visual Model

Optimization of Steamflooding Heavy Oil Reservoirs

Investigation of the plugging capacity and enhanced oil recovery of flexible particle three-phase foam

The foam reinforced with Janus amphiphilic graphene oxide to control steam channeling in heavy oil reservoir

Application of Flue Gas Foam-Assisted Steam Flooding in Complex and Difficult-to-Produce Heavy Oil Reservoirs

Construction and Mechanism of Janus Nano-Graphite Reinforced Foam Gel System for Plugging Steam in Heavy Oil Reservoirs

A Review of High‐Temperature Foam for Improving Steam Flooding Effect: Mechanism and Application of Foam

Experimental Study on Enhanced Oil Recovery Effect of Profile Control System-Assisted Steam Flooding

Experimental Study On Factors Affecting The Performance Of Foamy Oil Recovery

Computational study on the three phase displacement characteristics of foam fluids in porous media

Study on the mechanism of CO 2 composite system assisted steam stimulation of oil recovery efficiency in heavy oil reservoirs

A High-Temperature Plugging System for Offshore Heavy Oil Thermal Recovery.

Chemical Additives and Foam Assisted SAGD Model Development

Optimization Study of Injection and Production Parameters for Shallow- and Thin-Layer Heavy Oil Reservoirs with Nitrogen Foam-Assisted Steam Flooding

Optimization and Performance Evaluation of Foam Acid Systems for Plugging Removal in Low Pressure Oil and Gas Reservoirs

N 2 Foam Flooding Combined with Gel Plugging for Enhanced Oil Recovery in High-Temperature Reservoirs: Laboratory Experiments and Numerical Simulations

Numerical Modeling, Simulation and Lab Testing of Foam-Assisted Mud Cap Drilling Processes Dealing with Non-Newtonian Foam Rheology

Numerical Simulation of Gas Mobility Control by Chemical Additives Injection and Foam Generation During Steam Assisted Gravity Drainage (SAGD)

Foam Flowing Mechanisms of Steam-Foam Flooding for Heavy Oil Reservoirs

Pore-scale Experimental Study on EOR Mechanisms of Combining Thermal and Chemical Flooding in Heavy Oil Reservoirs

Investigation of the Stability Mechanism of Stimulus-Responsive Wormlike Micelle-CO2 Foams in the Oil Phase