Abstract:Kraft lignin grafted with hydrophilic polymers has been prepared using reversible addition-fragmentation chain-transfer (RAFT) polymerization and investigated for use as a surfactant. In this preliminary study, polyacrylamide and poly(acrylic acid) were grafted from a lignin RAFT macroinitiator at average initiator site densities estimated to be 2 per particle and 17 per particle. The target degrees of polymerization were 50 and 100, but analysis of cleaved polyacrylamide was consistent with a higher average molecular weight, suggesting not all sites were able to participate in the polymerization. All materials were readily soluble in water, and dynamic light scattering data indicate polymer-grafted lignin coexisted in isolated and aggregated forms in aqueous media. The characteristic size was 15-20 nm at low concentrations, and aggregation appeared to be a stronger function of degree of polymerization than graft density. These species were surface active, reducing the surface tension to as low as 60 dyn/cm at 1 mg/mL, and a greater decrease was observed than for polymer-grafted silica nanoparticles, suggesting that the lignin core was also surface active. While these lignin surfactants were soluble in water, they were not soluble in hexanes. Thus, it was unexpected that water-in-oil emulsions formed in all surfactant compositions and solvent ratios tested, with average droplet sizes of 10-20 μm. However, although polymer-grafted lignin has structural features similar to nanoparticles used in Pickering emulsions, its interfacial behavior was qualitatively different. While at air-water interfaces, the hydrophilic grafts promote effective reductions in surface tension, we hypothesize that the low grafting density in these lignin surfactants favors partitioning into the hexanes side of the oil-water interface because collapsed conformations of the polymer grafts improve interfacial coverage and reduce water-hexanes interactions. We propose that polymer-grafted lignin surfactants can be considered as random patchy nanoparticles with mixed hydrophilic and hydrophobic domains that result in unexpected interfacial behaviors. Further studies are necessary to clarify the molecular basis of these phenomena, but grafting of hydrophilic polymers from kraft lignin via radical polymerization could expand the use of this important biopolymer in a broad range of surfactant applications.

Tunable poly(lauryl methacrylate) surface grafting via SI-ATRP on a one-pot synthesized cellulose nanofibril macroinitiator core as a shear-thinning rheology modifier and drag reducer

Controlled Grafting of Well-Defined Polymers on Hydrogen-Terminated Silicon Substrates by Surface-Initiated Atom Transfer Radical Polymerization

Functionalization of Hydrogen-Terminated Silicon Via Surface-Initiated Atom-Transfer Radical Polymerization and Derivatization of the Polymer Brushes

Controlled Grafting of Well-Defined Epoxide Polymers on Hydrogen-Terminated Silicon Substrates by Surface-Initiated Atrp at Ambient Temperature

Surface-initiated Atom Transfer Radical Polymerization of Butyl Acrylate on Cellulose Microfibrils

Surface‐initiated Atom‐transfer Radical Polymerization (SI‐ATRP) of Methyl Methacrylate from Carbon Fibre

Graft Copolymers Prepared by Atom Transfer Radical Polymerization (ATRP) from Cellulose

In situ Surface‐Initiated ATRP Mediated by Gallium‐Based Liquid Metal Nanodroplets

ANCHORING OF AZO INITIATOR AND GRAFTING OF POLY(METHYL METHACRYLATE) ONTO NANAOMETER SILICA

Rapid Synthesis of Polymer-Grafted Cellulose Nanofiber Nanocomposite Via Surface-Initiated Cu(0)-Mediated Reversible Deactivation Radical Polymerization

Graft Polymerization of 2-Hydroxyethyl Methacrylate Via ATRP with Poly(acrylonitrile-Co-p-chloromethyl Styrene) As a Macroinitiator

All-Aqueous SI-ARGET ATRP from Cellulose Nanofibrils Using Hydrophilic and Hydrophobic Monomers

Tbcpma: A New Trifunctional Acrylic Monomer for Convenient Synthesis of A Well-Defined Amphiphilic Graft Copolymer by Successive Rdrp

Aqueous Polymer Modification of Cellulose Nanofibrils by Grafting‐Through a Reactive Methacrylate Group

Homogeneous grafting poly (methyl methacrylate) on cellulose by atom transfer radical polymerization

Preparation of Cellulose Graft Poly(methyl Methacrylate) Copolymers by Atom Transfer Radical Polymerization in an Ionic Liquid

Self-assembly of Catecholic Macroinitiator on Various Substrates and Surface-Initiated Polymerization.

Surface Functionalization of Polycaprolactone Films Via Surface-Initiated Atom Transfer Radical Polymerization for Covalently Coupling Cell-Adhesive Biomolecules.

Synthesization and Characterization of Lignin-graft-Poly (Lauryl Methacrylate) via ARGET ATRP

Polymer-grafted lignin surfactants prepared via reversible addition-fragmentation chain-transfer polymerization

An Efficient Way to Tune Grafting Density of Well-Defined Copolymers Via an Unusual Br-containing Acrylate Monomer