Abstract:Obtaining intergranular and transgranular fractures through grain boundary engineering has been considered an efficient technique that improves the effective fracture toughness of polycrystalline aggregates. In this paper, the idealized hexagonal microstructure, random microstructures, and microstructures of grains with large aspect ratios are analyzed through a semi-analytical approach and the cohesive finite element method. The results indicate that when the aspect ratio of grains is not too large, the crack paths consisting of intergranular and transgranular fractures are approximately Mode I fracture morphologies among these microstructures. As the ratio of toughness between grain boundaries and grains varies, the effective fracture toughness of the microstructure can be increased more than the grain boundary fracture toughness but cannot exceed the inner grain fracture toughness. In contrast, the microstructure of grains with a large aspect ratio leads to deflected crack paths that are unexpectedly obtained, which implies that the approximate Mode-I intergranular fracture along transverse direction is almost impossible. The results demonstrate that the projected energy dissipation rate along the direction perpendicular to the loading axis can be significantly improved beyond the inner grain fracture toughness by enlarging the aspect ratio of the grains. Nevertheless, the mixed-mode effective fracture toughness is still limited to the grain fracture toughness. Corresponding experiments are also carried out to qualitatively verify the numerical results. The underlying mechanism for this deflection of fracture path is due to the strong anisotropy of fracture toughness. The higher the grain aspect ratio, the greater the anisotropy of the macroscopic effective fracture toughness. The energy favored fracture path is determined by the largest ratio between the driving force and the toughness of fracture over all directions. Therefore, cracks cannot propagate in the direction of the maximum fracture toughness when the aspect ratio of the grain is sufficiently large. The fracture diagrams that vary with the aspect ratio of grain and the ratio of fracture toughness between the grain and grain boundary are provided. The results can provide valuable guidance for designing microstructures and improving fracture toughness in materials.

Intrinsic mechanism of grain size effect and grain boundary misorientation angle effect on crack propagation in martensitic steels

Effect of Crystallographic Orientation on Quenching Stress During Martensitic Phase Transformation of Carbon Steel Plate

Modeling Crack Propagation in Heterogeneous Granite Using Grain-Based Phase Field Method

Phase-field-crystal Simulation of Nano-Single Crystal Microcrack Propagation under Different Orientation Angles

Phase Field Crystal Study of Grain Boundary Structure and Annihilation Mechanism in Low-Angle Grain Boundary

Molecular dynamics study of the trans-grain extension behavior of crack tips under synergistic effects

Discrete element simulation study on effects of grain preferred orientation on micro-cracking and macro-mechanical behavior of crystalline rocks

Orientation Effect on Intergranular Fracture Behaviors along Symmetrical Tilt Grain Boundaries in Bcc Iron

Thermo-gaseous-mechanical coupling phase-field model for brittle crack propagation in tungsten

Investigation of Grain Boundary and Orientation Effects in Polycrystalline Metals by a Dislocation-Based Crystal Plasticity Model

Numerical Simulations of Crack Deflection at A Twist-Misoriented Grain Boundary Between Two Ideally Brittle Crystals

A two-set order parameters phase-field modeling of crack deflection/penetration in a heterogeneous microstructure

Could Effective Fracture Toughness of Polycrystalline Aggregates Exceed Inner Grain Fracture Toughness by Adjusting Toughness of Grain Boundary?

Modeling of inter- and transgranular stress corrosion crack propagation in polycrystalline material by using phase field method

Thermal cracking: clarifying the effects of phases, voids and grains through characterisation and crystal plasticity modelling

Molecular Dynamics Simulation on Intergranular Crack Propagation Along ∑3 Tilt Grain Boundary in Bcc Iron

Crossing grain boundaries in metals by slip bands, cleavage and fatigue cracks

Atomistic Scale Behaviors of Intergranular Crack Propagation along Twist Grain Boundary in Iron under Dynamic Loading

Molecular dynamics simulation of grain boundary geometry on crack propagation of bi-crystal aluminum

The role of crystallographic orientation of martensitic variants on cleavage crack propagation

Molecular dynamics simulation-based representation of intergranular fracture processes in austenitic steel