Abstract:Anion exchange membrane fuel cells (AEMFCs) have recently seen significant growth in interest as their achievable current density, peak power density, and longevity have been improved dramatically. Though these advances in performance have been important for demonstrating the feasibility of the technology, nearly all AEMFCs reported in the literature have required a relatively high loading of platinum group metal (PGM)-based catalysts at both the anode and cathode electrodes [1]. However, to take command of the low-temperature fuel cell market, AEMFCs cannot simply reach the same performance as incumbent proton exchange membrane fuel cells (PEMFCs), which have had decades of development and investment. AEMFCs must realize their most widely quoted advantage over PEMFCs and be produced at a much lower cost than PEMFCs. The most likely pathway to acceptably low cost will involve reducing the PGM loading in both electrodes. At the cathode, reasonable PGM-free catalysts exist, as will be shown in this work. At the anode; however, there are no practical contenders that exist to replace PGM-based catalysts. Hence, the most practical approach is to create transitional catalysts with ultra-low PGM content until future PGM-free catalysts can be realized. To reduce the platinum group metal (PGM) loading in anion exchange membrane fuel cell (AEMFC) electrodes, it is important to transition to catalysts with very low PGM content, and eventually to create catalysts that are completely PGM-free. One approach that can be used in both cases is to create atomically dispersed metals on a carbon support. In this work, four catalysts were prepared using a new, simple, scalable Controlled Surface Tension (CST) method: Pt/C, Pt/NC, PtRu/C, and PtRu/NC. CST is unique as it allows for a high density of very small multi-atom clusters, facilitated by altering the surface tension in the synthesis medium. The catalysts were physically characterized using a wide array of techniques, including high-resolution Cs aberration-corrected scanning transmission electron microscopy (STEM), extended X-ray absorption fine structure (EXAFS), and X-ray Absorption Near-Edge Structure (XANES). The catalysts were also tested for their oxygen reduction reaction and hydrogen oxidation reaction activity both ex-situ on a rotating ring-disk electrode and in-situ while integrated into the anode (PtRu) and cathode (Pt) of operating AEMFCs. With this new generation of low-PGM materials, it was possible to reduce the PGM loading by a factor of 14 while achieving comparable performance to commercial catalysts with a peak power density approaching 2 W/cm 2 . AEMFCs were also assembled with ultralow PGM loading (0.05 mgPGM/cm 2 ), where PtRu/NC anodes were paired with Fe–N–C cathodes [2], which allowed for the demonstration of cells with a specific power of 25 W/mg PGM (40 W/mg Pt ).

Improving Alkaline Hydrogen Oxidation Activity of Palladium through Interactions with Transition-Metal Oxides

Pd/CeO2 Interface with Abundant Oxygen Vacancies for Alkaline Hydrogen Evolution/Oxidation Reaction

Pt Single Atoms Coupled with Ru Nanoclusters Enable Robust Hydrogen Oxidation for High-Performance Anion Exchange Membrane Fuel Cells

Recent advances in platinum-group-metal based electrocatalysts for alkaline hydrogen oxidation reaction

Electrocatalysts for Hydrogen Oxidation Reaction in Alkaline Electrolytes

Carbon-Capped Monometallic and Bimetallic Catalysts for Hydrogen Oxidation Reaction (HOR) and Their Positive Features on Durability in Alkaline Conditions

Electrocatalytic Hydrogen Oxidation in Alkaline Media: From Mechanistic Insights to Catalyst Design

Single palladium site in ordered porous heteroatom-doped carbon for high-performance alkaline hydrogen oxidation

Surface Engineered Ru2Ni Multilayer Nanosheets for Hydrogen Oxidation Catalysis

(Invited) Development of Sustainable Electrocatalysts for Anion Exchange Membrane Fuel Cells and Electrolyzers

Bifunctional Mechanism of Hydrogen Oxidation Reaction on Atomic Level Tailored-Ru@pt Core-Shell Nanoparticles with Tunable Pt Layers

Dilute Pd‐Ni Alloy through Low‐temperature Pyrolysis for Enhanced Electrocatalytic Hydrogen Oxidation

Hydrogenated TiO2 Carbon Support for PtRu Anode Catalyst in High‐Performance Anion‐Exchange Membrane Fuel Cells

Alkaline hydrogen oxidation reaction on Ni-based electrocatalysts: From mechanistic study to material development

A Highly‐Efficient Boron Interstitially Inserted Ru Anode Catalyst for Anion Exchange Membrane Fuel Cells

Multi-Atom PGM Based Catalyst for Highly Efficient Oxygen Reduction Reaction(ORR) and Hydrogen Oxidation Reaction (HOR) in Alkaline Environment

Bimetallic Nickel-Molybdenum/tungsten Nanoalloys for High-Efficiency Hydrogen Oxidation Catalysis in Alkaline Electrolytes

Self-Optimized Ligand Effect in L1 2 -PtPdFe Intermetallic for Efficient and Stable Alkaline Hydrogen Oxidation Reaction

Hydrogen oxidation reaction in alkaline media: From mechanism to recent electrocatalysts

RuP Nanoparticles Supported on N, O Codoped Porous Hollow Carbon for Efficient Hydrogen Oxidation Reaction

Phase and Interface Engineering of a Ru-Sn Nanocatalyst for Enhanced Alkaline Hydrogen Oxidation Reaction