Abstract:It is essential to study the tensile fracture mechanism of additively manufactured materials and develop the effective process treatment techniques to improve their fracture resistance. In this paper, the effects of different treatment processes on the microstructure and tensile fracture properties of TC17 titanium alloy melted by laser selective zone melting were investigated. The static tensile fracture morphological characteristics were observed by combining SEM and EDS. The metallographic microstructure after chemical corrosion was observed optically. And the tensile fracture morphology of the three states of TC17 titanium alloy samples at room temperature conditions was investigated. The results show that the metallographic matrix microstructure of TC17 titanium alloy after HT, HIP and HIP-HT treatments was a bimodal structure with α+β phases, i.e., β phase was in the form of a net basket, and α phase was in the form of a coarse bar. The grain sizes of the samples treated by different processes were different, but the difference in grain size of the HT-treated tissues was small, and the difference in grain size of the HIP-HT-treated tissues was large. And the coarse α-phase segregation could be seen at the edge of the samples. The 3D-printed materials had complex changes in anisotropic properties affected by the printing structure and tissue. The printed tissues were brittle and had high internal stresses. These problems were partly improved at high temperatures, but they still existed. The HIP-HT-treated materials had a large α+β-phase bimodal structure. The HT-treated material had coarse grains and precipitation phases, poor room temperature plasticity, and improved high temperature plasticity. After HT treatment, the original printing microstructure changed, the strength and plasticity were significantly improved, but the macroscopic printing structure still had a slight influence on the fracture morphology. When HIP treatment temperature was higher, the influence of macroscopic printing structure basically disappeared, but the grain and microstructure grew up, and the strength and plasticity were slightly lower than that of the HT treatment. HIP process basically eliminated the unfused defects of the three-dimensional morphology, and the local weak bonding zone formed.

Effects of ion irradiation on microstructure of 316L stainless steel strengthened by disperse nano TiC through selective laser melting

Effect of helium bubbles on irradiation hardening of additive manufacturing 316L stainless steel under high temperature He ions irradiation

Damage behavior of additive manufacturing 316L stainless steel irradiated with Fe ions

Impact of sub-grain structure on radiation resistance in additively manufactured 316L stainless steels: An atomic insight into the mechanism

The Mechanisms of Inhibition Effects on Bubble Growth in He-Irradiated 316L Stainless Steel Fabricated by Selective Laser Melting

Hardening behavior of selective laser melted 304L stainless steel under Xe irradiation

Heavy ion irradiation response of an additively manufactured 316LN stainless steel

Effect of Solid Solution Temperature on Material Properties and Microstructure of Inconel 718/TiC Composites by Selective Laser Melting

Effects of Titanium-Implanted Dose on the Tribological Properties of 316L Stainless Steel

Effects of different treatment processes on microstructure and tensile fracture behaviour of selected laser melting TC17 titanium alloy

Mechanism of Mechanical Property Enhancement in Nitrogen and Titanium Implanted 321 Stainless Steel

Effect of Heat Treatment on Microstructures and Mechanical Properties of SS316L by Micro Selective Laser Melting

Atomic Origins of Radiation-Induced Defects and Interfacial Strengthening in Additively Manufactured Titanium Aluminide Alloy Irradiated with Kr-Ions at Elevated Temperature

Microstructure Changes of Domestic T91 and 316Ti Steels Irradiated by Xe+ Ions

Strengthening Mechanisms in Selective Laser Melted 316L Stainless Steel

Effect of Post Heat Treatment on the Microstructure and Tensile Properties of Nano TiC Particulate Reinforced Inconel 718 by Selective Laser Melting

Influence of Annealing Heat Treatment on the Microstructure and Mechanical Properties of Multilayer 316L-TiC Composite Fabricated by Selective Laser Melting

Melting and solidification dynamics during laser melting of reaction-based metal matrix composites uncovered by in-situ synchrotron X-ray diffraction

Characterization of microstructure and hardening of SLM nickel-based alloy irradiated by He ions

The Structural Transitions of Ti3AlC2 Induced by Ion Irradiation

Effect of in-situ Transverse Magnetic Field on Microstructure, Mechanical Properties and Corrosion Resistance of the Directed Energy Deposited 316 L Stainless Steel