Abstract:Ultrasonic additive manufacturing (UAM) is an advanced joining technique that utilizes ultrasonic vibrations to bond layers of metal foil together. UAM offers several benefits over traditional manufacturing methods, including enhanced design flexibility and reduced material waste, and its potential applications in various industries such as aerospace, automotive, and biomedical engineering are being actively explored. The study employs a nanoindentation apparatus to investigate the effect of the UAM process on the local mechanical properties of the bonded interface, along with changes in microstructure, which were investigated using scanning electron microscopy and electron back-scattered diffraction. The results revealed a significant correlation between material hardness and local plasticity. EBSD has revealed that the grain size distribution of Al far from the interface contains 57% of the grains less than 3 μm in size, while at the interface this number rises to approximately 78%, indicating that the average grain size decreases as it approaches the interface. This result is consistent with nanoindentation results that demonstrated a gradual change in the hardness of Al foil far from the interface to close to the interface (the maximum penetration depth near the interface was 500 nm less than far from the interface). Both EBSD and nanoindentation disclose the effect of work hardening close to the interface, which is related to dislocation accumulation with a density of beneath the interface. The consistency of hardness and Young's modulus with the pole figures and microscopic images demonstrated that plasticity flow and fine grain distribution would only occur in the vicinity of the interface in the softer metal region. Although the harder metal did not exhibit plasticity or recrystallization, the hardness, and Young's modulus map indicated the formation of a layer of small grains close to the interface on the aluminum side owing to strain hardening and dynamic recrystallization.

Multi-layer solid-state ultrasonic additive manufacturing of aluminum/copper: local properties and texture

Strengthening Effects at Dissimilar Metal Interfaces Created by Ultrasonic Additive Manufacturing

Effect of ultrasonic amplitude on interfacial characteristics and mechanical properties of Ti/Al laminated metal composites fabricated by ultrasonic additive manufacturing

Dynamic Recrystallization and Recovery in Very High‐Power Ultrasonic Additive Manufacturing

In-situ study of tensile behavior of Ti/Al laminated metal composites fabricated via ultrasonic additive manufacturing

Microstructure characteristics and mechanical properties of Cu/Al laminated metal composites fabricated by electropulsing assisted ultrasonic additive manufacturing

Microstructure Evolution of 1100 Al Alloy Multi-Foils During Ultrasonic Additive Manufacturing

The Effects of Layer Thickness on the Mechanical Properties of Additive Friction Stir Deposition-Fabricated Aluminum Alloy 6061 Parts

Influence of ultrasonic parameters on microstructural refinement and defect elimination in ultrasound-assisted laser-based metal additive manufacturing

Novel Technique for Design and Manufacture of Alternating Gradient Composite Structure of Aluminum Alloys Using Solid State Additive Manufacturing Technique

Effect of multi-layer deposition in solid-state friction stir surfacing-based additive manufacturing for fabrication of large-scale metal product

Processing aluminum alloy with hybrid wire arc additive manufacturing and ultrasonic nanocrystalline surface modification to improve porosity, surface finish, and hardness

Effect of material position and tool offset on the microstructure and mechanical properties of friction stir welded AA7075/AZ31B with ultrasonic assistance

Integrating Fiber Optic Strain Sensors into Metal Using Ultrasonic Additive Manufacturing

High plasticity in refractory composite fabrication by ultrasonic additive manufacturing

Evolution of microstructure and properties in 2219 aluminum alloy produced by wire arc additive manufacturing assisted by interlayer friction stir processing

Microstructure and mechanical properties of Ti/Al laminates fabricated by ultrasonic additive manufacturing assisted by joule heat and post-welding heat treatment

Wire arc additive manufacturing of Al-Zn-Mg-Cu alloy: Microstructures and mechanical properties

Effect of Ultrasound on Microstructure and Properties of Aluminum–Copper Friction Stir Lap Welding

Ultrasonic-induced Deformation Nanostructures in Coarse-Grained Aluminum Wires at Room Temperature

Microstructure and Interface Evolution of Diamond/cu Composites Prepared Via Ultrasonic Additive Manufacturing (UAM)