Abstract:Porous NiTi lattice structures are widely used in the manufacture of crucial components owing to their excellent shape memory effect, superelasticity, and high damping capacities. However, the specific strength and lightweight characteristics of porous NiTi lattice structures fabricated by conventional technologies are limited by unpredictability. In this work, three types of porous NiTi structures based on triply periodic minimal surface (TPMS) – Diamond, Gyroid, and Primitive – were designed and manufactured by the laser powder bed fusion (LPBF) additive manufacturing process . This work demonstrates LPBF is a feasible and efficient approach to fabricate highly accurate porous NiTi TPMS structures. Moreover, the influence of each of these structures on the mechanical and shape memory properties was investigated. Among the three structures, Gyroid had the smallest volume fraction deviation. Furthermore, the Diamond structure had the largest compressive modulus (782.82 MPa) and ultimate yield strength (163.14 MPa). The Gyroid and Primitive structures exhibit excellent elastic recovery deriving from high values of compressive modulus (662.44 MPa, and 703.29 MPa), and can maintain reliable structural robustness. The Primitive structure exhibited the lowest mechanical properties (37.80 MPa). During the cyclic compression test, Gyroid and Primitive show a smaller unrecovered strain than Diamond. Primitive shows the largest recovered strain during the heating process (6.98%). The higher mechanical flexibility of Primitive structure endows this structure with higher recovery ratio. During the direct compression test, the residual strain exhibits a positive correlation with the loading strain. All three structures exhibit good deformation recovery capability with a strain of 4%. At a strain of 12%, recovered strain during heating became the dominant factor in the recovery of the TPMS structure. Overall, porous NiTi TPMS structures are capable of reversible compressibility composed of rapid elastic recovery and controllable shape memory recovery. The unique performance of porous NiTi TPMS structure fabricated by LPBF renders it a highly efficiency energy-absorbing structure.

3D Chiral Energy-Absorbing Structures with a High Deformation Recovery Ratio Fabricated via Selective Laser Melting of the NiTi Alloy

Energy Absorption Characteristics of Novel Bio-Inspired Hierarchical Anti-Tetrachiral Structures

Three-Dimensional High-Entropy Alloy–Polymer Composite Nanolattices That Overcome the Strength–Recoverability Trade-off

A ready-to-manufacture optimization design of 3D chiral auxetics for additive manufacturing

Deformation mechanism of innovative 3D chiral metamaterials

Design and analysis of three-dimensional chiral metamaterials for enhanced torsional compliance

Origami-Inspired Chiral Metamaterials with Tunable Circular Dichroism Through Mechanically Guided Three-Dimensional Assembly

Topological optimisation and laser additive manufacturing of force-direction-sensitive NiTi porous structures with large deformation recovery behaviour

Shock-Resistant and Energy-Absorbing Properties of Bionic NiTi Lattice Structure Manufactured by SLM

Additive manufacturing of three-dimensional (3D)-architected CoCrFeNiMn high- entropy alloy with great energy absorption

Machine learning guided design of mechanically efficient metamaterials with auxeticity

Mechanical Properties of Hierarchical Anti-Tetrachiral Metastructures

Mechanical and shape memory properties of NiTi triply periodic minimal surface structures fabricated by laser powder bed fusion

Crushing behavior of contact-aided AlSi10Mg sandwich structure based on chiral mechanical metamaterials

Mechanical behavior analyses of 4D printed metamaterials structures with excellent energy absorption ability

Innovative 3D chiral metamaterials under large deformation: Theoretical and experimental analysis

A Novel Auxetic 3D Lattice Structure for Enhancing Energy Absorption

Volume Fraction Effect on the Mechanical and Shape Memory Properties of NiTi Gyroid Lattice Structure Fabricated by Laser Powder Bed Fusion

4D Printing of Chiral Mechanical Metamaterials with Modular Programmability using Shape Memory Polymer

Design and additive manufacturing of a modified face-centered cubic lattice with enhanced energy absorption capability

Additive-manufactured hierarchical multi-circular lattice structures for energy absorption application