Abstract:Regarding the issue of intense mining pressure appearing in the underlying gateway below the remaining coal pillar in the close‐distance coal seam (the remaining coal pillar is perpendicular to the underlying section coal pillar), 401 working face is used as the engineering background. Field measurements, laboratory experiments, numerical simulations, and engineering verification techniques are used to study the abutment pressure's evolution properties and the plastic zone's propagation laws before and after the underlying coal seam roadway experienced the mining impact. The conclusions are as follows: 1 The maximum plastic area on the two sides and the roof of the roadway underlying the gob are up to 2 m and 1.5 m, whereas the maximum plastic area on the two sides and the roof of the roadway underlying the remaining coal pillar are up to 5 m and 4.5 m, respectively. Moreover, the plastic area extends along the two sides, and the section coal pillar is completely broken when the working face is mined below the remaining coal pillar. 2 The stress increase coefficient K in the overlap area of the remaining coal pillar and the underlying section coal pillar reaches 3.4 when the mining face penetrates the underlying remaining coal pillar and the advance abutment pressure is overlaid with the concentrated stress of the coal pillar. 3 When the underlying working face is mined to 4 m, ‐2 m, ‐8 m, and ‐14 m away from the remaining coal pillar, the damage range of the roadway 5‐10 m ahead increases in turn. At the same time, the maximum plastic area of the roof passes through the plastic area of the upper coal seam floor. Therefore, the underlying and transition areas on both sides of the remaining coal pillar are divided into Area I (15 m) → Area II (the most complicated area to control under the remaining coal pillar, 20 m) → Area III (25 m) according to the width. Furthermore, the divisional differentiated combined control technology of channel steel truss anchor cable with joint double‐way locking control function of roof and coal pillar in Area I and Area III, while channel steel truss anchor cable with joint double‐way locking control function of roof and side + high resistance integral door‐type support is proposed in Area II. Field engineering practice shows that the deformation of the roadway surrounding rock can be controlled within 210 mm after adopting the above divisional combined control technology. Finally, the mining operation can safely and efficiently pass through the remaining coal pillar. The research results have important reference values for surrounding rock control of mining roadways in the overlapping area of similar "+" type cross‐working face.This article is protected by copyright. All rights reserved.

Overburden Stress Arch Elevation Effect Induced by Roof Cutting and Destress Technique in Coal Mine Longwall Panel and Its Control Mechanism to Entry Surrounding Rock

Research on the Stability Mechanism of the Surrounding Rock of Gob-Side Entry Retaining by Roof Cutting in Dianping Coal Mine

Stability Control of a Goaf-Side Roadway under the Mining Disturbance of an Adjacent Coal Working Face in an Underground Mine

An Innovative Mechanism of Directional Rock Cracking Mechanics and Mine Pressure Control Method for Energy-Gathering Blasting

Stability Control of a Roadway Surrounding Rock during the Cutting and Pressure Relief of a Coal-Bearing Roof at a Shallow Mining Depth

Study on stress distribution law of surrounding rock of roadway under the goaf and mechanism of pressure relief and impact reduction

Research on Surrounding Rock Deformation and Mining Field Stress Distribution during Gob‐Side Entry Retaining by Roof Cutting and Pressure Releasing in the Inclined Thick Coal Seam

Controlled reconstruction and application research of lateral overlying strata structure in high-gas mines with thick-hard roofs for a fully-mechanized top-caving face

Mechanisms and Applications of Pressure Relief by Roof Cutting of a Deep-Buried Roadway near Goafs

Deformation mechanism and control technology of gob-side roadway with continuous mining and continuous backfilling: a case study

Parameters and surrounding rock control of gob-side driving under double key stratum after roof cutting

Surrounding Rocks Deformation Mechanism and Roof Cutting-Grouting Joint Control Technology for Soft and Thick Coal Seam Roadway

Study on small coal pillar in gob-side entry driving and control technology of the surrounding rock in a high-stress roadway

Deformation mechanism and control technology of gob-side entry retaining with roadside backfilling: a numerical analysis and field investigation

Mechanism and Control Technology of Rockburst Induced by Thick Hard Roof and Residual Coal Pillar: A Case Study

Parameter determination and effect evaluation of gob-side entry retaining by directional roof cutting and pressure releasing

Stress Evolution and Surrounding Rock Control During Coal Seam Mining Under the Influence of Overlying and Adjacent Goafs

Analysis of Surrounding Rock Control Technology and Its Application on a Dynamic Pressure Roadway in a Thick Coal Seam

Differential roof cutting for roadway support in dual gob-side entry retention on a single working face − Multilevel continuous anchor-grouting control technology: A case study

Research on roof damage mechanism and control technology of gob-side entry retaining under close distance gob

Failure mechanism and divisional differentiated control of surrounding rock in mining roadway under remaining coal pillar in close‐distance coal seam