Abstract:Metallic components fabricated with powder bed fusion additive manufacturing (AM) processes are known to have defects arising from liquid-solid phase transformation. Friction stirring can be an effective alternative source of heat, as evidenced in some of the recently developed powder deposition-based solid-state AM processes. However, they possess practical issues such as making compacted powder feedstock beforehand, consolidation of powder filler inside the tool during deposition followed by necessary extrusion, and significant flash formation, among a few. This paper proposed a novel powder bed friction stir (PBFS) additive manufacturing process inside a specifically designed mould that could potentially mitigate such issues in the existing technologies. The process was successfully demonstrated by building single-track and parallel double-track 3D structures layer-by-layer from an AA6061 powder bed using a rotating non-consumable friction stirring tool. Furthermore, for a better understanding of the underlying process mechanics, deposits were analyzed for their surface topography, microstructural evolution, and mechanical performance under different heat inputs as well as different print locations. Different heat inputs were applied by varying the friction-stirring pitch (FS pitch) from 'Low' to 'High'. The print locations analysis was carried out in a parallel double-track fabricated at the optimal FS pitch. The results revealed that the 'High' FS pitch yielded an increased percentage of recrystallized grains and a fraction of high-angle grain boundaries as well as a larger average grain size due to the high heat input, better material intermixing, and the dominance of continuous dynamic recrystallization. As a result, an improved mechanical performance, except for the microhardness, was observed. The 'High' FS pitch also exhibited an improved surface topography. The results also revealed that the relative dominance of the re-stirring-induced recrystallization and the reheating-induced plastic deformation was the key factor for the variation of the microstructure in the longitudinal, transverse, and short-transverse directions. A gradual decrease in the tensile strength was observed from the 'Top' to the 'Bottom' segments of the overlapped region, contrary to the central region of a track.

Effects of process parameters on properties of friction stir additive manufactured copper

Effects of Multipass Additive Friction Stir Processing on Microstructure and Mechanical Properties of Al-Zn-Cup/Al-Zn Laminated Composites

Restirring and Reheating Effects on Microstructural Evolution of Al–Zn–Mg–Cu Alloy during Underwater Friction Stir Additive Manufacturing

A Critical review on the performance and microstructural characteristics of materials fabricated through friction stir additive methods and deposition techniques

Experimental and numerical analysis of friction stir additive manufacturing of 2024 aluminium alloy

Friction stir additive manufacturing – An innovative tool to enhance mechanical and microstructural properties

Friction stir-based additive manufacturing

Friction stir additive manufacturing enabling scale-up of ultrafine-grained pure copper with superior mechanical properties

Development and analysis of a powder bed friction stir (PBFS) additive manufacturing process for aluminium alloys: A study on friction-stirring pitch (ω/v) and print location

Additive friction stir deposition of al 7075 parts and the effect of heat treatment on microstructure, electroconductivity, and mechanical properties

Evaluation of Microstructural, Mechanical and Corrosion Behaviours of Laminated AA6061/AA7075 Metal Matrix Composites Build by Friction Stir Additive Manufacturing for Structural Applications

A Framework to Simulate Friction Stir Additive Manufacturing (FSAM) Using the Finite Element Method

Influence of Friction Stir Processed Parameters on Superplasticity of Al-Zn-Mg-Cu Alloy

Effect of Material Extrusion Method on the Microstructure and Mechanical Properties of Copper Parts

The Effects of Layer Thickness on the Mechanical Properties of Additive Friction Stir Deposition-Fabricated Aluminum Alloy 6061 Parts

Evolution of Material Properties and Residual Stress with Increasing Number of Passes in Aluminium Structure Printed via Additive Friction Stir Deposition

Enhancing 3D Printing Copper-PLA Composite Fabrication via Fused Deposition Modeling through Statistical Process Parameter Study

Effect of build orientation and post-build heat treatment on the mechanical properties of cold spray additively manufactured copper parts

An Investigation on Effects of Process Parameters in Fused-Coating Based Metal Additive Manufacturing

Microstructural and Mechanical Characterization of Additive Friction Stir-Deposition of Aluminum Alloy 5083 Effect of Lubrication on Material Anisotropy

Research Progress of Friction Stir Additive Manufacturing Technology