Abstract:Abstract Commercial aircraft today require efficient high-lift and control systems on the wings to reduce the drag in flight or decrease the take-off and landing speeds. Morphing mechanisms are one approach for improved high-lift systems. In most cases the objective function is an increased lift to drag ratio or the noise reduction. On closer examination control systems as well as morphing mechanisms are located in a certain wing segment. The transition between a moving wing part and the fixed wing is a step, which creates additional vortices. This segments the wing in span-wise direction and reduces the efficiency. A flexible skin between a moving and a fixed wing parts smooths the contour and minimize the efficiency reduction of the wing. A full scale demonstrator of a wing segment was manufactured with two flexible skin designs. The first subcomponent connects a morphing leading edge with a rib of the wing over a span of one meter. The skin is a material mix of ethylene-propylene-diene monomer (EPDM) rubber and fiberglass-reinforced plastic. The rubber is the basis of the skin and the glass-fiber is added as local skin stiffeners in the form of strips in chord-wise direction. The second subcomponent blends the aileron with a rib of the wing in a triangular design. The connection of three different hinges realizes a morphing triangle, which is loaded in an in-plane shear only state of stress in each aileron position. The core of the triangle is a 3D printed structure, which is free in shear. The covering skin is a combination of EPDM with carbon fibers oriented in +/−30° direction to obtain shear compliance and to resist the loads on the triangle. The deformation of each concept is identified at the demonstrator. Therefore, an optical measurement system scans the surface in the initial and deflected state. The required deformation precision of the concepts differs due to their design. The contour at the leading edge requires a certain shape over the span. The analysis of the skin buckling is one requirement at the transition triangle during the aileron motion. The experimental results show a smooth transition contour at the leading edge and no buckling effects at the triangle. The results can be used for the validation of simulation models. Furthermore, both skin concepts cover the gap between a moving wing segment and a fixed wing part. The elimination of steps in span-wise direction can improve the aero-acoustic behavior along the wing for future aircraft.

Development of an Active Wingtip for Aeroelastic Control

Application of Aeroelastic Tailoring for Load Alleviation on a Flying Demonstrator Wing

Experimental and numerical investigation of an aircraft wing with hinged wingtip for gust load alleviation

On the Fine-Tuning of the Stick-Beam Wing Dynamic Model of a Tiltrotor: A Case Study

A Smart Wing Model: From Design to Testing in a Wind Tunnel with a Turbulence Generator

Active Control and Wind Tunnel Test Verification of Multi-control Surfaces Wing for Gust Alleviation

A New X-Actuator Design for Controlling Wing Bending and Twisting Modes

A NEW X-ACTUATOR DESIGN FOR DUAL BENDING/TWISTING CONTROL OF WINGS

Optimum Induced Drag of Wingtip Devices: The Concept of Best Winglet Design

A Resilient Approach to a Test Rig Setup in the Qualification of a Tilt Rotor Carbon Fiber-Reinforced Polymer (CFRP) Wing

On the Dynamic Behavior of Wings Incorporating Floating Wingtip Fuel Tanks

Aerodynamic load control in horizontal axis wind turbines with combined aeroelastic tailoring and trailing‐edge flaps

On the Aeroelasticity of a Cantilever Wing Equipped with the Spanwise Morphing Trailing Edge Concept

Morphing Wingtip Structure Based on Active Inflatable Honeycomb and Shape Memory Polymer Composite Skin: A Conceptual Work

Design and Validation of the Trailing Edge of a Variable Camber Wing Based on a Two-Dimensional Airfoil

A new hybrid control methodology for a morphing aircraft wing-tip actuation mechanism

Fluidic Flow Control Devices for Gust Load Alleviation

Experimental Study of Flexible Skin Designs Between a Moving Wing Segment and a Fixed Wing Part on a Full Scale Demonstrator

Aero‐servo‐elastic co‐optimization of large wind turbine blades with distributed aerodynamic control devices

Aeroelastic Vibration Feedback Control of Smart Aircraft Wings in Subsonic Flight Speeds

Aeroelastic Response and Active Control of Aircraft Wings Modeled as Thin-Walled Beams