Abstract:High-performance composites made from polymer matrix materials with a long-life span, durability, and low weight are needed in the automotive, household products, and aerospace industries. Lightweight, good specific stiffness, and excellent specific quality are all characteristics of polymer fiber–reinforced composites. The current study examines the mechanical and wear characteristics of PALF/sisal fiber and silicon nanoparticle (SiO 2 )–reinforced hybrid polymeric composites with various weight percentages, such as 0–8 wt%. Employing mechanical mixing and sonication, SiO2 NPs are dispersed inside a polymer matrix throughout the production process. After that, the nanocomposites are thoroughly characterized to determine their mechanical characteristics, such as their tensile strength, bending strength, and impact strength. Furthermore, tribological experiments like pin-on-disc and wearing measurements of volume are used to evaluate the wear resistance of the hybrids. The C-type hybrids had the greatest mechanical characteristics among the five distinct types of hybrids (i.e., 53.36 MPa tensile, 61.25 MPa flexural, and 4.98 J of impact energy). Adding 4 wt.% silicon nanoparticles decreases volumetric degradation by 8–13% even under typical loading conditions when compared to A-type hybrids. The presence of silicon nanofillers in the fiber matrix composition could be responsible for the lower tendency for volumetric degradation. The rate of wear was noticed to decrease as silicon content increased, and then, after reaching the minimum values for C-type composites, wear started rising as silicon content increased further. To comprehend the entire performance of the nanocomposites, the physical variables, such as density and retention of water, are also investigated. The theoretical and experimental densities of nanocomposites are 1.221–1.253 g/cm 3 and 1.211–1.24 g/cm 3 , respectively, and have been observed to rise with increasing silicon particle concentration. The findings will aid in the creation of environmentally friendly and high-performing materials for use in a variety of industries, including the packaging sector, construction, and automobile sectors, where enhanced mechanical features and durability against wear are important. In the end, this study provides expanded knowledge of the viability of using SiO2 nanoparticles to improve the performance of organic fiber–reinforced polymeric composites.

Effectiveness of silicon nanoparticles on the mechanical, wear, and physical characteristics of PALF/sisal fiber–based polymer hybrid nanocomposites

Improvements in Compatibility and Properties of Biocomposites Modified Through Nanosilica Attachment

Effect of Alumina and Silicon Carbide Nanoparticle-Infused Polymer Matrix on Mechanical Properties of Unidirectional Carbon Fiber-Reinforced Polymer

Effect of Al2O3 and SiC Nano-Fillers on the Mechanical Properties of Carbon Fiber-Reinforced Epoxy Hybrid Composites

Mechanical and dynamic characterization of SiO2 nanofiller-based Luffa cylindrica fibre composites structures using finite element method

Influence of rice husk ash Si3N4 ceramic on mechanical, wear and low cycle fatigue behavior of hybrid pineapple/basalt fiber reinforced polyester composite

Synergistic Effects of Hybrid Graphitic Nanofillers on Simultaneously Enhanced Wear and Mechanical Properties of Polymer Nanocomposites

Experimental Investigation of the Mechanical Properties of Carbon/Basalt/SiC Nanoparticle/Polyester Hybrid Composite Materials

Treated sisal fiber made epoxy composite hybridize with silicon carbide nanoparticles: Characteristics study

Fiber reinforcement of polymer hybrid sandwich composites using SNiPs: effect of silica nanoparticles on flexural and compressive strength

Sliding Wear Performance of Nano-Sio2/short Carbon Fiber/epoxy Hybrid Composites

Effect of SiC Nanoparticles on Mechanical and Damping Properties of Epoxy/Polysulfide Rubber Blend Composite

Mechanical, tribological, and surface morphological studies on the effects of hybrid ilmenite and silicon dioxide fillers on glass fibre reinforced epoxy composites

Morphology and Tribological Behaviors of in Situ Polymerized Nano-Sio2/Polyacrylate Nanocomposites

Characterisation of Nanocellulose from Waste Pisum Sativum Sheath and its Sunn Hemp Fibre-Polyester Composite: A Step Towards Valorisation of Biomass

Improvement of low-velocity impact and tribo-mechanical properties of unsymmetrical hybrid composites through addition of nanoclay

Friction and wear properties of polyacrylonitrile‐ and pitch‐based carbon fiber‐reinforced polymer matrix composites containing silicon carbide nanoparticles

Influence of silane treatment on the mechanical, tribological and morphological properties of corn stalk fiber reinforced polymer composites

A Novel Approach on Reusing Silicon Wafer Kerf Particle as Potential Filler Material in Polymer Composite

Mechanically Robust and Abrasion-Resistant Polymer Nanocomposites for Potential Applications As Advanced Clearance Joints

Morphology and Tribological Behaviors of <i>In Situ</i> Polymerized Nano-SiO<sub>2</sub>/Polyacrylate Nanocomposites