Abstract:The adsorption of emulsifier on latex particle surfaces often determines the stability of the latex. However, relatively few adsorption isotherms have been published because these experiments are difficult and time-consuming. This paper describes the determination of adsorption isotherms using a new serum replacement technique, which was developed to characterize latex particle surfaces by removing adsorbed emulsifier from the latex particle surfaces and solute electrolyte from the aqueous phase. The latex is confined in a cell with a Nuclepore filter membrane, and doubly-distilled, deionized water is pumped through the latex to replace the serum. This method allows complete recovery of the serum, as well as determination of the concentration profile of the desorbing species in the effluent stream. To determine adsorption isotherms, a known amount of emulsifier is added to a cleaned latex and the concentration profile of the emulsifier in the effluent stream is measured. A material balance between added emulsifier and desorbed emulsifier (from the concentration profile) gives the adsorption isotherm. This adsorption isotherm is correlated with the predictions of a mathematical model of the process. The adsorption of technical-grade sodium lauryl sulfate, Aerosol MA, and Aerosol OT on a Dow monodisperse polystyrene latex of 190 nm diameter determined at 23 ± 2° follows a Langmuir adsorption isotherm. The mole-r culaç areas at saturation are 42 - 43 A2 , 39 - 45 A2, and 85 -100 A2, respectively. The adsorption of sodium lauryl sulfate on a monodisperse polymethyl methacrylate latex of 330 nm diameter also follows a Langmuir absorption isotherm and gives a molecular area at saturation of 57 A2. The adsorption of sodium lauryl sulfate on a monodisperse polyvinyl acetate latex of 165 nm diameter does not follow a Langmuir adsorption isotherm, but instead gives a curve characteristic of porous surfaces. The molecular area at saturation is 30 A2.

A Spectroscopic Method for Studying the Morphology of Latexes

Morphology Observation of Latex Particles with Scanning Transmission Electron Microscopy by a Hydroxyethyl Cellulose Embedding Combined with RuO4 Staining Method

Effect of hydrophilic comonomer and surfactant type on the colloidal stability and size distribution of carboxyl- and amino-functionalized polystyrene particles prepared by miniemulsion polymerization.

PREPARATION AND CHARACTERIZATION OF SULFONATED POLYSTYRENE LATEXES

Express method for particle size analysis in solid, liquid, and amorphous materials using 3D calibration curve and 2D-DLS dynamic light scattering

Laser light scattering from concentrated solutions of polystyrene latex spheres: A comparative study

Study of Emulsion Morphology by Electron Spectroscopy

Determination of Local Young's Modulus Values on the Polymer Surface by Contact Force Spectroscopy

Characterization of Spherical Microlatex Particles Made of Linear Uncrosslinked Polystyrene Chains

Morphology Of P(Ba-St-Daam) Latex Particles Prepared By Seeded-Emulsion Polymerization

Infrared Spectra Investigation on Pendent Double Bonds in Monodisperse Micron Macroporous Resin

Mini-emulsion formation and polymerization of styrene

Rapid Measurement of Adsorption Isotherms of Emulsifiers on Latex Particles

Neutron and X-ray Scattering Characterization of Silica Nanoparticle-Stabilized Polymer Hybrid Latex Particles

Particle Size and Morphology of Poly[styrene‐co‐(butyl Acrylate)]/nano‐silica Composite Latex

Analysis of Ft-Ir Spectra of the Sulfonated Polystyrene Colloidal Crystals

Synthesis and Properties Study of the Uniform Nonspherical Styrene/Methacrylic Acid Copolymer Latex Particles

Wavelength exponent based calibration for turbidity spectroscopy: Monitoring the particle size during emulsion polymerization reactions

Morphology Control of Soap-Free Seeded P(St–EA–AA) Latex Particles

Polyelectrolyte assisted charge titration spectrometry: Applications to latex and oxide nanoparticles

Preparation of magnetic polystyrene latex via the miniemulsion polymerization technique