Abstract:Injection of CO2 and water in saline aquifers or oil reservoirs causes changes of pressure, saturation and concentrations that affect the state of stress and promote chemical reactions in the host rock, resulting in porosity and permeability variations. It is therefore a coupled hydro-mechanical and chemical (HMC) problem. Numerical simulation of multiphase and multicomponent flow of CO2, oil and water with mechanical coupling allows realistic modeling of the reservoir and cap rocks. Carbonate reservoirs are geological formations composed mainly of minerals such as calcite and dolomite which can dissolve or precipitate in the medium when injecting a fluid of chemical composition and temperature different from those of the fluids initially contained in the rock. Water-weakening due to matrix acidification of carbonates is a well-known phenomenon that can be modeled by including mineral concentrations as state variables in the stress-strain behavior of the material. The objective of this work is to characterize synthetic carbonate rocks through microtomography and petrography techniques, focusing on a comparative analysis before and after load application and degradation with a reactive fluid [1]. The synthetic rocks were subjected to physical characterization (mineralogy, computed tomography and porosity) and mechanical characterization (uniaxial compressive strength and Brazilian tests) before and after the dissolution process. The petrographic analysis verified an increase in both intergranular and intragranular porosities after dissolution. The microtomography analysis quantified the maximum increase in porosity, from 11.8% to 41.3% in the two-dimensional analysis and 31.6% to 52% in the three-dimensional analysis of the porous structures. Furthermore, the pores were quantified according to their area, and data was obtained on the orientation of the pores, providing insight into the preferred paths of fluid flow. It was also observed that the microtomography technique was an effective tool for characterizing fractures in the samples before and after dissolution [1]. Dissolution tests were also performed in a modified oedometer cell adapted to measure horizontal stress. The dissolution phase was conducted using water and an acid solution to evaluate the influence of the pH on the mechanical behaviour of the samples. When the sample in the oedometric cell is exposed to an acid solution under constant vertical load of 400kPa, vertical displacement takes place (volume decrease of the sample) and horizontal stress increases (Figure 1). The synthetic rock used in this experiment is mainly composed by calcite, with small additions of calcium hydroxide, and the reactive fluid is water acidified with acetic acid (with 10% concentration). This material is manufactured in laboratory in order to have greater control of its constituents and reproducibility of experimental results. During the acidification phase of the experiment, the sample was subjected to an acid flow with a pressure differential of 12kPa for 7h. The behavior in Figure 1 was also observed by [2] and [3]. The model for degradation of carbonatic soft rocks proposed by [2] was implemented in a finite element code capable of performing coupled THMC analyzes in porous media [4]. This model is based on the Critical State Theory with the introduction of a bonding variable that controls the size of the yield surface by modifying the tensile strength and the pre-consolidation stress of the material. In Figure 1 it is also possible to see that the HMC coupled simulation of the oedometric test was able to reproduce the experimental results in terms of volumetric strain and horizontal stress. In Figure 2 tomographic images of the synthetic carbonate rock before and after exposure to the acid solution in an oedometric cell under constant vertical load are presented. Such analyses are crucial for the injection of reactive fluids, such as CO2, at high depths. Dissolution of minerals will affect not only the porosity and permeability of the reservoir rock but also, possibly, the stress state in the vicinity of the injection well.

Modeling the impact of pH and reservoir temperature on the dissolution of quartz mineral due to oilfield chemical treatment

The Effects of Selected Minerals on Laboratory Simulated Thermochemical Sulfate Reduction

Simulation study on the mining conditions of dissolution of low grade solid potash ore in Qarhan Salt Lake

Numerical simulation of the thermo-hydro-chemical coupling in enhanced geothermal systems: Impact of SiO 2 dissolution/precipitation in matrix and fractures

Effect of Mixed Mineralogy on Etching Profile and Conductivity in Acid Fracturing in Naturally Fractured Carbonate Reservoirs

Reaction Rates in Chemically Heterogeneous Rock: Coupled Impact of Structure and Flow Properties Studied by X-ray Microtomography.

Qualitative dissolution modeling of etch‐pit formation on the K‐feldspar surface through phase‐field approach

Effect of pH on Spontaneous Imbibition in Calcareous Rocks

Minerals Dissolution Effect on the Mechanical Properties of Synthetic Carbonate Rocks

Environmental impact of solution pH on the formation and migration of iron colloids in deep subsurface energy systems

Elemental Dissolution Characteristics of Granite and Gabbro under High-Temperature Water-Rock Interactions.

Influences of real-time acid-rock reaction heat on etched fracture dimensions during acid fracturing of carbonate reservoirs and field applications

Influence of clay minerals on pH and major cation concentrations in acid-leached sands: Column experiments and reactive-transport modeling

Impact of Oilfield Chemicals on Contiguous Technologies

THE CORROSION AND ITS MECHANISM OF ORGANIC ACIDS ON MAIN MINERALS IN OIL-GAS RESERVOIR SAND ROCKS

Impact of secondary coatings on the dissolution rate of K-feldspar: A combined experimental and modeling study

Analyzing the Dynamics of Mineral Dissolution during Acid Fracturing by Pore-Scale Modeling of Acid-Rock Interaction

Pore-Scale Numerical Simulation of Acid-Rock Reaction Processes in Carbonate Reservoirs

Evaluation of Interactions Between Oilfield Chemicals and Reservoir Rocks