Abstract:The frictional behaviors of implant soft materials in vivo are important to medical effect. In this study, hydroxyethyl acrylate sodium/acryloyldimethyl taurate copolymer (EMT-10) aqueous dispersions are adopted, acting as lubricants in hydrophobic polydimethylsiloxane elastomer (PDMS) Gemini interfaces or hydrophilic polyamide hydrogel (PAM) Gemini interfaces, respectively. The associations exist in EMT-10 aqueous dispersions via hydrogen bonding, electrostatic and hydrophobic interactions, similar to bio-lubricants. The EMT-10 aqueous dispersions, surface characteristics of Gemini interfaces and the axial force (N-a) during frictional experiments in Stribeck curves are studied. Under low and high concentrations of EMT-10 lubricant, the PDMS Gemini interfaces exhibit opposing sensitivity to N-a, different from the PAM Gemini interfaces, which always showing lower CoF at higher N-a. This phenomenon results from the various degree of perfection for lubrication film between the Gemini interfaces. To further distinguish the lubrication film formation, and correlate frictional surface characteristic and rheological behaviors of lubricant, a new parameter, relative thickness (phi), is established. When phi<1, the lubrication film is discrete, and the boundary lubrication regime plays dominant role during the frictional test. When phi>1, the entire lubrication film forms and the whole system enters hydrodynamic lubrication regime. For PDMS Gemini interfaces, the lubrication film is composed of the confined and adsorbed EMT-10 polymer chains owing to the strong attraction between the hydrophobic surface and the C-C backbone. As a result, the lubrication film is greatly affected by the concentration of the lubricant thus phi increases. The PDMS frictional system gradually converts from the boundary into hydrodynamic lubrication regime. For PAM Gemini interfaces, the film is made of the hydrogel surface mesh and the confined EMT-10 chains, so phi is always larger than 1, exhibiting the characteristic of hydrodynamic lubrication regime. The study tends to probe the frictional behavior of the complex fluids in the soft Gemini interfaces and unveils the mechanism behind the phenomenon. [GRAPHICS] .

Synergistic effect of sharkskin-inspired morphologies and surface chemistry on regulating stick-slip friction

Universal and Stable Slippery Coatings: Chemical Combination Induced Adhesive-Lubricant Cooperation

Synergistic Effect of Microconvex Texture and Particle Medium on the Tribological Property of the Rubber Sliding Interface

Two-step printing Ni3Al/Cr3C2-Ti3SiC2/MoS2 composite films using electrohydrodynamic atomization with a biomimetic shark-skin mask

Multiplex Biomimetic SLIPS With Super‐Lubricity to Multiphase Matters

Construction of biomimetic textures and modification of self-lubrication mechanisms on the surface of sulfonated polyether ether ketone films

Friction behavior of rough polydimethylsiloxane surfaces under hydrophobic polymer aqueous solution conditions

Di-particles-derived Slippery Lubricant-Infused Porous Surface with Broad Anti-Adhesion Performance

Effects of Laser Surface Texturing and Lubrication on the Vibrational and Tribological Performance of Sliding Contact

Biomimetic lubricant-grafted surfaces on laser-textured microwell arrays with multifunctionality

Studies on the Lubrication Between Hydrophilic-Hydrophilic/Hydrophobic-Hydrophobic Gemini Interfaces and Complex Fluids

Strengthening mechanism of different morphologies of nano-sized MSH on tribological performance of phosphate/MoS2 bonded solid lubricating coatings

Design and preparation of biomimetic polydimethylsiloxane (PDMS) films with superhydrophobic, self-healing and drag reduction properties via replication of shark skin and SI-ATRP

Stick-Slip Behaviours of Water Lubrication Polymer Materials under Low Speed Conditions

Constructing a biomimetic robust bi-layered hydrophilic lubrication coating on surface of silicone elastomer

Numerical simulation on hydrodynamic lubrication performance of bionic multi-scale composite textures inspired by surface patterns of Subcrenata and Clam shells

Synergistic Effect of Carbon Micro/Nano-Fillers and Surface Patterning on the Superlubric Performance of 3D-Printed Structures

Tribofilm Formation and Friction Reduction Performance on Laser-Textured Surface with Micro-Grooved Structures

The relationship between surface microstructure and super-lubrication performance based on 2D LDHs

Evaluation of tribological performance for laser textured surfaces with diverse wettabilities under water/oil lubrication environments

Superlubricity Achieved with Zwitterionic Brushes in Diverse Conditions Induced by Shear Actions