Abstract:Innovative clean label processes employed in the manufacture of acid gels are targeted to modify the structure of proteins that contribute to rheological properties. In the present study, CO2-treated milk protein concentrate powder with 80% protein in dry matter (TMPC80) was mixed with nonfat dry milk (NDM) in different ratios for the manufacture of acid gels. Dispersions of NDM and TMPC80 that provided 100, 90, 70, and 40% of protein from NDM were reconstituted to 4.0% (wt/wt) protein and 12.0% (wt/wt) total solids. Dispersions were adjusted to pH 6.5, followed by heat treatment at 90°C for 10 min. Glucono-δ-lactone was added and samples were incubated at 30°C, reaching pH 4.5 ± 0.05 after 4 h of incubation. Glucono-δ-lactone levels were adjusted to compensate for the lower buffering capacity of samples with higher proportions of TMPC80, which is attributable to the depletion of buffering minerals from both the serum and micellar phase during preparation of TMPC80. Sodium dodecyl sulfate-PAGE analysis indicated a higher amount of caseins in the supernatant of unheated suspensions with increasing proportions of CO2-treated TMPC80, attributable to the partial disruption of casein micelles in TMPC80. Heat treatment reduced the level of whey proteins in the supernatant due to the heat-induced association of whey proteins with casein micelles, the extent of which was larger in samples containing more micellar casein (i.e., samples with a lower proportion of TMPC80). Particle size analysis showed only small differences between nonheated and heated dispersions. Gelation pH increased from ˜5.1 to ˜5.3, and the storage modulus of the gels at pH 4.5 increased from ˜300 to ˜420 Pa when the proportion of protein contributed by TMPC80 increased from 0 to 60%. Water-holding capacity also increased and gel porosity decreased with increasing proportion of protein contributed by TMPC80. The observed gel properties were in line with microstructural observations by confocal microscopy, wherein sample gels containing increasing levels of TMPC80 exhibited smaller, well-connected aggregates with uniform, homogeneous pore sizes. We concluded that TMPC80 can be used to partially replace NDM as a protein source to improve rheological and water-holding properties in acid gels. The resultant gels also exhibited decreased buffering, which can improve the productive capacity of yogurt manufacturing plants. Overall, the process can be leveraged to reduce the amount of hydrocolloids added to improve yogurt consistency and water-holding capacity, thus providing a path to meet consumer expectations of clean label products.

Impact of Combined Thermal Pressure Treatments on Physical Properties and Stability of Whey Protein Gel Emulsions

Fabrication and characterisation of whey–pea protein‐based emulsion gels induced by transglutaminase cross‐linking

Study on potential antigenicity and functional properties of whey protein treated by high hydrostatic pressure based on structural analysis

The impact of whey protein preheating on the properties of emulsion gel bead

The effect of homogenization and heat treatment on gelation of whey proteins in emulsions

Stability of oil‐in‐water emulsions as influenced by thermal treatment of whey protein dispersions or emulsions

Effect of Heat Treatment on Physicochemical and Emulsifying Properties of Polymerized Whey Protein Concentrate and Polymerized Whey Protein Isolate

Effect of Heat Treatment on Emulsification and Stability of WPC and WPI

Effect of Heat Treatment on the Stability of Ultrasound-Assisted Cross-Linked Myofibrillar Protein-Stabilized Emulsion Filler Phases Via Rheology and Tribology

Ph-, Ion- and Temperature-Dependent Emulsion Gels: Fabricated by Addition of Whey Protein to Gliadin-Nanoparticle Coated Lipid Droplets

Physicochemical and rheological properties of soybean protein emulsions processed with a combined temperature/high-pressure treatment

Cold, gel-like whey protein emulsions by microfluidisation emulsification: Rheological properties and microstructures

Characterization of O/W emulgels based on whey protein-alginate-inulin coacervates: Influence of temperature and ultrasound as protein preconditioning process

Gelation of soybean proteins induced by sequential high-pressure and thermal treatments

Improved Gel Properties of Whey Protein-Stabilized Emulsions by Ultrasound and Enzymatic Cross-Linking

Comparative Study of Heat- and Enzyme-Induced Emulsion Gels Formed by Gelatin and Whey Protein Isolate: Physical Properties and Formation Mechanism

Effect of Preheated Whey Protein Concentrate on the Physical Stability of Oil-in-water Emulsions

Batch versus microfluidic emulsification processes to produce whey protein microgel beads from thermal or acidic gelation

Effect of High Pressure Treatment on Interfacial Properties, Structure and Oxidative Stability of Soy Protein Isolate-Stabilized Emulsions

Influence of Thermal Treatment and Soy Bean Protein Characteristics on Muscle Protein Emulsion Stability

Influence of partially demineralized milk proteins on rheological properties and microstructure of acid gels