Abstract:The experimental work aims to study the effect of the Copper (Cu) addition on the tribological and electrochemical behaviour of porous Ti 50 Ni 50-x -Cu x alloys. In the first step pure metal powders of titanium (Ti), nickel (Ni), and Cu were ball-milled during 8 h in a planetary ball mill, and then compacted under a 4 ton load to obtain pre-alloyed powders. The final step is sintering at 950°C for 7 h in a tubular furnace under a controlled atmosphere. X-ray diffraction measurements (XRD), scanning electron microscopy (SEM) analyses, microhardness measurements, friction tests and electrochemical were carried out to characterise the tribological and electrochemical performances of the elaborated specimens. DRX results reveal the formation of four major phases: TiNi, Ti 2 Ni, TiNi 3 and TiNi 0.8 Cu 0.2 . Potentiodynamic polarisation tests show the positive effect of adding Cu on corrosion resistance, where the 6% Cu sample exhibits the best corrosion behaviour. Tribological results show a decrease in the coefficient of friction and wear rate with the addition of Cu, compared to the initial state, without Cu addition. The minimum coefficient of friction (0.585) was recorded for the 2% Cu sample, while the minimum wear rate (Ws = 1.06. E −4 mm 3 /N/m) was achieved for the 4% Cu sample. Le travail expérimental vise à étudier l'effet de l'ajout de cuivre (Cu) (de 0 à 6%) sur le comportement tribologique et électrochimique des alliages poreux Ti 50 Ni 50-x -Cu x . Dans la première étape, on a broyé des poudres métalliques pures de titane (Ti), de nickel (Ni) et de Cu pendant 8 heures dans un broyeur planétaire à boulets, puis on les a compactées sous une charge de 4 tonnes pour obtenir des poudres pré-alliées. L'étape finale est un frittage à 950°C pendant 7 heures dans un four tubulaire sous atmosphère contrôlée. On a réalisé des mesures de diffraction des rayons X (DRX), des analyses par microscopie électronique à balayage (MEB) et des mesures de microdureté pour caractériser les performances tribologiques et la résistance anticorrosion des spécimens élaborés, à l'aide d'essais de frottement et électrochimiques. Les résultats révèlent la formation de trois phases majeures: TiNi, Ti 2 Ni et TiNi 3 pour tous les échantillons, et la formation de la phase intermétallique TiNi 0.8 Cu 0.2 avec l'ajout de Cu, d'après l'analyse par diffraction des rayons X. Les essais de polarisation potentiodynamique montrent l'effet positif de l'ajout de Cu sur la résistance à la corrosion, où l'échantillon à 6% de Cu montre le meilleur comportement à la corrosion. Les résultats tribologiques montrent une diminution du coefficient de frottement et du taux d'usure avec l'ajout de Cu, par rapport à l'état initial, sans ajout de Cu. On a enregistré le coefficient de frottement minimum (0.585) pour l'échantillon à 2% de Cu, alors que l'on a obtenu le taux d'usure minimum (Ws = 1.06 E −4 mm 3 /N/m) pour l'échantillon à 4% de Cu.

Comparison on Microstructural Evolution and Wear Behavior of Cu–10Sn–XNi Alloy Composite Developed Through GTA Surface Alloying and Friction Stir Processing

Study on microstructure and tribological property of aluminium-nickel composites fabricated by bottom pour stir casting

A Novel Real-Time Assessment of the Wear Analysis of Cu-Ni-Sn Hybrid Composite for Multifunctional Applications Strengthened by Nano B4C

Microstructure, Mechanical, and Tribological Relationship in Cu-12Al-Ni Alloy with Respect to the Variation of Ni Content

Characterization of microstructure and wear behavior of nickel modified Zn-27% Al alloy casting

The effect of friction stir processing on mechanical, wear and corrosion characteristics of Cu-AlN-BN surface composite

Influence of Cu Content Variation on the Tribological Properties of Ni60CuMo with Sandwich-Structured Composite Coatings by Laser Cladding

Development of Al-Ni-TiC Composite Coating on Commercially Pure Al Using Tungsten Inert Gas Welding Route and its Wear Behavior

Synergetic influence of TiCnp and graphite particles on tribological performance of Cu based composites prepared by flake powder metallurgy

Microstructural Evolution & Mechanical Properties of ZrO2/GNP and B4C/GNP reinforced AA6061 Friction Stir Processed Surface Composites - A Comparative study

INFLUENCE OF NICKEL ON THE MICROSTRUCTURAL EVOLUTION AND MECHANICAL PROPERTIES OF LM6-ALLOY-BASED FUNCTIONALLY GRADED COMPOSITE TUBES

Tribological and electrochemical behaviour study of porous TiNiCu alloys manufactured by the powder metallurgy process

Effect of nanostructured Cu on microstructure, microhardness and wear behavior of Cu-xGnP composites developed using mechanical alloying

Study on the friction and wear properties of nickel-based-WC-10Ni composite coatings prepared on the surface of TC4 titanium alloy

Wear mechanism, subsurface structure and nanomechanical properties of additive manufactured Inconel nickel (IN718) alloy

The Effect of Coating Grain Size on the Selective Oxidation Behaviour of Ni-Cr-Al Alloy

Tribological analysis and machine learning modeling of nickel-coated graphite reinforced A206 metal matrix composites

Surface CuAl9Mn2/W Composites Prepared by Multipass Friction Stir Processing: Microstructures, Phases, and Mechanical and Tribological Properties

Development of wear resistant Cu-12Sn-1.5Ni alloy via minor addition of Fe during casting process

Sliding Wear Behavior of Fully Nanotwinned Cu Alloys

Friction and Wear Resistance of Nanostructured TiNi Shape Memory Alloy