Abstract:Background: Injectable hyaluronic acid fillers are routinely used for correction of soft-tissue volume loss and facial rejuvenation. Product differentiation has primarily been based on the rheologic parameter known as elastic modulus (G′), although other physicochemical properties are being explored to characterize potential product performance. As clinical data regarding product performance are lacking, the practical experience of injectors provides a valuable bridge in the knowledge gap between product rheologic data and product use. Methods: Rheologic and physicochemical measurements (swelling factor and cohesion) were collected for 18 products. To observe the impact of G′ and hyaluronic acid concentration on swelling factor and cohesion, proportional relationships were evaluated. Contributing authors were queried regarding their G′-based selection of products when considering skin quality, degree of correction, injection depth, and anatomical location. Results: Relationships were observable between G′ and swelling factor and G′ and cohesion only when limited to products manufactured by the same crosslinking technology and the same concentration. No relationship between isolated hyaluronic acid concentration and swelling factor or cohesion was apparent. Although rheological parameters and the assumptions of ex vivo data translating to in vivo performance are oftentimes not completely aligned, in the clinical experience of the authors, in general, higher G′ products are better suited for thicker skin and deeper injection planes, whereas lower G′ products are better for more superficial planes, although exceptions to these trends are also made based on technical experience. Conclusions: While rheologic and physicochemical characteristics can vary widely between products and the methods and measurements of these parameters are often difficult to correlate, G′ represents a useful and consistent parameter for product differentiation. Understanding how to select products based on G′ is valuable knowledge for customizing injection plans and contributes to an optimal aesthetic outcome.

Deformation characteristics of hydrogel products based on cross‐linked hyaluronic acid

Injectable and Moldable Hydrogels for Use in Sensitive and Wide Range Strain Sensing Applications

Rheological Characteristics of Hyaluronic Acid Fillers as Viscoelastic Substances

Mimicking the Mechanical Properties of Cartilage Using Ionic- and Hydrogen-Bond Cross-Linked Hydrogels with a High Equilibrium Water Content above 70%

Investigation of the Degradation-Retarding Effect Caused by the Low Swelling Capacity of a Novel Hyaluronic Acid Filler Developed by Solid-Phase Crosslinking Technology

Engineering the Viscoelasticity of Gelatin Methacryloyl (gelma) Hydrogels Via Small “dynamic Bridges” to Regulate BMSC Behaviors for Osteochondral Regeneration

Preparation and Rheological Evaluation of Thiol–Maleimide/Thiol–Thiol Double Self-Crosslinking Hyaluronic Acid-Based Hydrogels as Dermal Fillers for Aesthetic Medicine

The Intrinsic Relation between the Hydrogel Structure and In Vivo Performance of Hyaluronic Acid Dermal Fillers: A Comparative Study of Four Typical Dermal Fillers

A Covalently Cross-Linked Hyaluronic Acid/Carboxymethyl Cellulose Composite Hydrogel as a Potential Filler for Soft Tissue Augmentation

Performance assessment of an injectable hyaluronic acid/polylactic acid complex hydrogel with enhanced biological properties as a dermal filler.

The rheology of injectable hyaluronic acid hydrogels used as facial fillers: A review

Comparison of the Rheological Properties of Viscosity and Elasticity in Two Categories of Soft Tissue Fillers: Calcium Hydroxylapatite and Hyaluronic Acid

Modulation of biomechanical properties of hyaluronic acid hydrogels by crosslinking agents

Comparative Rheology of Hyaluronic Acid Fillers, Poly-l-lactic Acid, and Varying Dilutions of Calcium Hydroxylapatite

The histologic reaction and permanence of hyaluronic acid gel, calcium hydroxylapatite microspheres, and extracellular matrix bio gel

Rheologic and Physicochemical Properties Used to Differentiate Injectable Hyaluronic Acid Filler Products

Hyaluronan Hydrogels: Rheology and Stability in Relation to the Type/Level of Biopolymer Chemical Modification

Development of Dispersion Process to Improve Quality of Hyaluronic Acid Filler Crosslinked with 1,4-Butanediol Diglycidyl Ether

Comparison of Hyaluronidase-Mediated Degradation Kinetics of Commercially Available Hyaluronic Acid Fillers In Vitro

In vivo evaluation of MMP sensitive high-molecular weight HA-based hydrogels for bone tissue engineering.

Structural Analysis of Hyaluronic Acid Fillers Using Nuclear Magnetic Resonance: Implications for Quality Control and Clinical Performance