Application of Synthesized Biomass Bamboo Charcoal–Iron Oxide “BC/Fe” Nanocomposite Adsorbents in the Removal of Cationic Methylene Blue Dye Contaminants from Wastewater by Adsorption

Tushar Kanti Sen

DOI: https://doi.org/10.3390/su15118841

IF: 3.9

2023-05-30

Sustainability

Abstract:In this work, synthesized, raw-bamboo-biomass-based magnetic “BC/Fe” bamboo charcoal–iron oxide nanocomposite adsorbents were characterized and tested for their effects on the removal of aqueous-phase cationic methylene blue (MB) dye pollutants from synthetic wastewater through a laboratory batch adsorption study. This batch adsorption study aimed to identify various physico-chemical process parameters such as initial dye concentration, solution pH, adsorbent dose, temperature, and their effects on the adsorption kinetics and adsorption isotherm characteristics. From the kinetic studies, it was found that the amount of MB dye adsorption by synthesized adsorbents qe (mg/g) increased from 9.50 mg/g to 15.30 mg/g with the increase in the initial dye concentration range of 10 to 30 ppm, as per contact time, but decreased with the increase in the temperature range from 30 to 60 °C and the adsorbent doses from 20 to 40 mg, respectively, under specified experimental process conditions. From the kinetic study, it was also found that equilibrium was reached within 120 min, the adsorption kinetics followed three mechanistic steps, and the pseudo-second-order (PSO) kinetic model was applicable to explain the data of the batch adsorption kinetics. The various kinetic model parameters were determined from a fitted model equation. Furthermore, there was an increase in the amount of the MB dye adsorption qe (mg/g) from 9.87 mg/g to 17.62 mg/g with the increase in the solution pH from 3 to 7, and a reduction in the amount of dye adsorption qe (mg/g) was found at the solution pH of 10 for a 20 ppm MB dye solution at 30 °C. Both the Freundlich and Langmuir isotherm models were applicable to the equilibrium data, and the maximum adsorption capacity from the Langmuir isotherm fitting was 111.11 mg/g, which was comparative to or even better than many other magnetic adsorbents for methylene blue dye adsorption. Finally, the regeneration and reusability of the magnetic “BC/Fe” bamboo charcoal–iron oxide nanocomposite materials as well as the limitations of these batch adsorption studies are also discussed here.

environmental sciences,environmental studies,green & sustainable science & technology

What problem does this paper attempt to address?

This paper aims to solve the problem of removing methylene blue dye pollutants in wastewater treatment. Specifically, through laboratory batch adsorption studies, the author tested the application effect of the synthesized biomass bamboo - charcoal - iron oxide nanocomposite ("BC/Fe") in removing cationic methylene blue dye pollutants in synthetic wastewater. The research mainly focuses on the following aspects:

1. **Identifying various physicochemical parameters affecting the adsorption process**: including the influence of factors such as initial dye concentration, solution pH value, adsorption dosage, and temperature on the characteristics of adsorption kinetics and adsorption isotherms.
2. **Studying adsorption kinetics and equilibrium**: Under different process conditions, determine the capacity and adsorption mechanism of the adsorbent, and evaluate its regeneration and reuse ability through rapid desorption studies.
3. **Verifying the applicability of the adsorbent**: Evaluate the potential application value of these nanocomposites in actual wastewater treatment, especially the feasibility in continuous column experimental design and plant - scale studies.

### Main research objectives:
- **Testing the effectiveness of the synthesized "BC/Fe" nanocomposite in adsorptive removal of cationic methylene blue dye**.
- **Identifying and optimizing various basic parameters affecting the adsorption process** to provide a basis for future continuous column experimental design.
- **Studying the adsorption kinetics and equilibrium characteristics of methylene blue dye** to determine the capacity, adsorption mechanism, and its regeneration and reuse performance of the adsorbent.

### Research methods:
- **Batch adsorption kinetics experiment**: Through shaking table experiments, change the initial solution pH value, adsorption dosage, initial dye concentration, and temperature to study the kinetic behavior of the adsorption process.
- **Equilibrium adsorption isotherm experiment**: Conduct experiments at different initial methylene blue concentrations to determine the maximum adsorption capacity of the adsorbent and the characteristics of the adsorption isotherm.
- **Data fitting and analysis**: Use pseudo - first - order (PFO) and pseudo - second - order (PSO) kinetic models as well as Freundlich and Langmuir isotherm models to fit experimental data and analyze the adsorption mechanism and adsorption capacity.

### Key formulas:
- **Calculation of adsorption amount**:
\[
q_t=\frac{(C_0 - C_t)V}{m}
\]
\[
\text{Percentage of adsorption}=\left(\frac{C_0 - C_t}{C_0}\right)\times100\%
\]
where \(C_0\) is the initial dye concentration (mg/L), \(C_t\) is the dye concentration at time \(t\) (mg/L), \(V\) is the volume of the reaction mixture (L), and \(m\) is the mass of the adsorbent added to the solution (g).

- **Pseudo - first - order kinetic model**:
\[
\log(q_e - q_t)=\log q_e-\frac{k_1t}{2.303}
\]

- **Pseudo - second - order kinetic model**:
\[
\frac{t}{q_t}=\frac{1}{k_2q_e^2}+\frac{t}{q_e}
\]

- **Freundlich isotherm model**:
\[
\ln q_e=\ln K_f+\frac{1}{n}\ln C_e
\]

- **Langmuir isotherm model**:
\[
\frac{1}{q_e}=\frac{1}{K_aq_m}\left(\frac{1}{C_e}\right)+\frac{1}{q_m}
\]

- **Separation factor \(R_L\)**:
\[
R_L=\frac{1}{1 + K_aC_0}
\]

Through these studies, the author hopes to provide new ideas and methods for the development of efficient and sustainable wastewater treatment technologies.