Abstract:Aluminum is an important additive in solid propellants used to improve energy efficiency, but agglomeration of aluminum particles can reduce the specific impulse of the engine, increase two-phase flow losses and cause ablation of the adiabatic layer. Therefore, it is important to understand the mechanism of formation, mode of movement and particle size characteristics of aluminum agglomerates in solid propellants to study the inhibition of agglomeration. In this paper, a three-dimensional numerical simulation of aluminum particle agglomeration near the burning surface of solid propellants was conducted using the discrete unit method based on direct tracking calculations of the detailed motion of individual particles. The model considered physical processes such as burning surface motion, aluminum particle precipitation, turbulent pulsation and the heating and melting of aluminum particle and used a grid-based contact detection method to accelerate the computational process. The agglomeration process of a solid propellant with specific formulation was experimentally investigated. Aluminum particle aggregates underwent splitting, and the final aluminum particle agglomerates were spherical droplets with typical structure. The agglomeration process of this propellant was investigated by means of a simulation. The accuracy of the agglomeration model was verified by comparing the results of the model for the agglomeration process and the shape and size distribution of agglomerates with available experimental data. Compared with the experimental results, the deviations of the equivalent particle sizes of agglomerates D-10, D-50, D-90, D-4,D-3, and D-3,D-2 obtained by using the simulation results were 6.3%, 6.3%, 9.4%, 7.5% and 6.7%, respectively. The aluminum particle agglomeration model established in this paper can predict the particle size distribution of aluminum agglomerates near the burning surface of solid propellants. The model was also used to further investigate the effects of aluminum particle content, ammonium perchlorate (AP) particle size and environ-mental pressure on aluminum particle agglomeration. Increasing the aluminum content or AP particle size aggravated aluminum particle agglomeration, whereas increasing pressure weakened it.

Drag and Heat Transfer of Metal and Oxide Agglomerates in a Flow of Solid-Propellant Combustion Products

Numerical Simulation of Aluminum Particle Agglomeration Near the Burning Surface of Solid Propellants

Numerical Simulation of Nanoparticle Synthesis in Diffusion Flame Reactor

A new robust modeling strategy for multi-component droplet heat and mass transfer in general ambient conditions

Exploring the Combustion Mechanism of Single Micron-Sized Aluminum Particles with a Numerical Model

Numerical Simulation of Reacting Flow in the Combustion Chamber and Study of the Impact of Turbulent Diffusion Coefficients

Modeling Droplet Vaporization and Combustion with the Volume of Fluid Method at a Small Reynolds Number

Numerical Simulation for Combustion of Droplet with Volume of Fluid Formulation

Investigation on Burning Behaviors of Aluminum Agglomerates in Solid Rocket Motor with Detailed Combustion Model

Drag force and heat transfer characteristics of deformable alumina droplets in compressible flows

Numerical Study of Micron-Scale Aluminum Particle Combustion in an Afterburner Using Two-Way Coupling CFD–DEM Approach

A Heat Transfer Model for Aluminum Droplet/wall Impact

Numerical Modeling of In-Flight Molten Metal Droplet Dynamics and Particle Oxidation in Atmospheric Plasma Spraying

Modeling of micron-sized aluminum particle combustion in hot gas flow

Numerical modeling of heat transfer behavior for two-phase flow in a nozzle considering phase change

A grain-scale modeling on the surface burning and agglomeration of the metalized solid propellants

A Simplified Theoretical Model for the Vapor-Phase Combustion of Metal Particles†

Numerical modelling and simulation of heat transfer for micro-sized spherical Al-4.5 wt% Cu alloy particles

Numerical Investigation of In-Flight Behavior of Fe-Based Amorphous Alloy Particles in AC-HVAF Thermal Spray Process

Numerical Modeling of High-Enthalpy Two-Phase Flow in a Channel with Transverse Injection of a Reactive Liquid

Model and Powder Particle Heating, Melting, Resolidification, and Evaporation in Plasma Spraying Processes