Abstract:Background Marginal fit significantly impacts the long-term success of dental restorations. Different pattern fabrication methods, including hand-waxing, milling, or 3D printing, may affect restorations accuracy. The effect of porcelain firing cycles on the marginal fit of metal-ceramic restorations remains controversial, with conflicting findings across studies. Purpose The aim was to evaluate the potential effects of multiple porcelain firings (3, 5, 7 cycles) as well as pattern fabrication method (conventional hand-waxing, milling, and 3D printing) on the marginal adaptation of 3-unit implant-supported metal-ceramic fixed partial dentures. It was hypothesized that neither the wax pattern fabrication method nor repeated ceramic firings would significantly affect the marginal adaptation of metal-ceramic crowns. Methods In this in-vitro study, 30 Cobalt-Chromium alloy frameworks were fabricated based on pattern made through three techniques: conventional hand-waxing, CAD-CAM milling, and CAD-CAM 3D printing ( n = 10 per group). Sixteen locations were marked on each abutment to measure the vertical marginal gap at four stages: before porcelain veneering and after 3, 5, and 7 firing cycles. The vertical marginal gap was measured using direct microscopic technique at ×80 magnification. Mean vertical marginal gap values were calculated and two-way ANOVA and Tukey’s post hoc tests were used for inter-group comparisons (α = 0.05). Results The 3D printing group showed significantly lower ( P <0.001) mean vertical marginal gaps (60–76 μm) compared to the milling (77–115 μm) and conventional hand-waxing (102–110 μm) groups. The milling group exhibited a significant vertical gap increase after 3 firing cycles ( P <0.001); while the conventional ( P = 0.429) and 3D printing groups ( P = 0.501) showed no significant changes after 7 firing cycles. Notably, the vertical marginal gap in all groups remained below the clinically acceptable threshold of 120 μm. Conclusion CAD-CAM 3D printing provided superior marginal fit compared to CAD-CAM milling and conventional hand-wax pattern fabrication methods. The impact of porcelain firing on the mean marginal gap was significant only in the milling group. All three fabrication techniques yielded clinically acceptable vertical marginal adaptation after repeated firings. Additive manufacturing holds promise to produce precise implant-supported prostheses.

Moving from analogue to digital workflows in dentistry: Understanding undermilling and overmilling as detrimental factors in fabricating CAD/CAM crowns

Effect of Machining Method and Margin Design on the Accuracy and Margin Quality of Monolithic Zirconia Crowns

Effect of CNC-milling on the marginal and internal fit of dental ceramics: a pilot study

[Management and Improving the Marginal Adaptation of Chairside Computer Aided Design/computer Aided Manufacturing Restorations].

The effect of dental restoration geometry and material properties on biomechanical behaviour of a treated molar tooth: A 3D finite element analysis

Influence of various fabrication techniques and porcelain firing on the accuracy of metal-ceramic crowns

Performance of Stereolithography and Milling in Fabricating Monolithic Zirconia Crowns with Different Finish Line Designs.

Comparing the accuracy of crown fitting between milling and 3D printing techniques using CAD/CAM technologies

Influence of CAD-CAM milling strategies on the outcome of indirect restorations: A scoping review

Effects of design software program and manufacturing method on the marginal and internal adaptation of esthetic crowns for primary teeth: A microcomputed tomography evaluation

Influence of fabrication settings on the in-vitro performance of subtractively manufactured resin-based molar crowns

The effect of cement and impression methods on the marginal and internal adaptation of the current monolithic blocks - 3D scanning evaluation

Evaluation of the Mechanical and Adhesion Characteristics of Indirect Restorations Manufactured with Three-Dimensional Printing

Influence of impression method and shoulder design on the marginal adaptation of CAD/CAM nanoceramic resin onlay restorations

Digital Modeling Technology for Full Dental Crown Tooth Preparation

The effect of two preparation designs on the fracture resistance and marginal adaptation of two types of ceramic crowns using CAD/CAM technology (In vitro study)

Surface trueness and precision of interim restorations fabricated by digital light processing and CAD-CAM milling systems

Digital Technologies for Restorative Dentistry

Effect of the CAD/CAM Milling Protocol on the Fracture Behavior of Zirconia Monolithic Crowns

Design of Wear Facets of Mandibular First Molar Crowns by Using Patient-Specific Motion with an Intraoral Scanner: A Clinical Study.

Marginal fit of 3-unit implant-supported fixed partial dentures: Influence of pattern fabrication method and repeated porcelain firings