Abstract:Aims: An eco-friendly coating emulsion prepared with mixture of oils of sesame and grape seed and alkyd-based waterborne varnish. The prepared emulsion applied four different wood substrates (walnut, beech, cedar and fir) in order to be investigated for some selected surface properties. Study Design: Several test methods were used to evaluate surface physicochemical properties of the coatings. The results obtained may be suggested for the selection of the best varnish-emulsion formulation for the improvement wood substrates and could provide useful evaluation of the test methods employed. Methodology: The wood species of Beech (Fagus sylvatica), Walnut (Juglans regia), Cedar (Cedrus libani) and Fir (Abies nordmandiana) were selected for the investigation. Commercially available alkyd based waterborne varnish was supplied ready to use form. Both sesame oil (Sesamum indicum L.) and grape seed oil (Vitis vinifera L.) were obtained from a Original Research Article Sahin and Erbil; AJB2T, 7(1): 1-9, 2021; Article no.AJB2T.66475 2 company that produces them by the cold press technique commercially. Both oils were used as supplied, without additional processing. These oils were added to varnish at 10% and 20% proportions (volume/volume). The 5 μl of distilled water (surface tension of 72.6 mN /m) was applied on wood surface by a sessile droplet method to measure surface contact angles. The surface hardness and scratch resistance of the cured varnish layers on wood substrates were measured with using pencil hardness test procedure according to ASTM-D-3363 standard. Cross cut test also conducted according to EN ISO 2409 standard. Experimental Findings: It was found that coated walnut samples show 9.8 to 13.5° higher contact angle values in all directions while other three wood samples only show marginally different values (0.1 to 4.3°). The highest contact value of 35.9° and 35.8° was found with samples of Wg20 and Wg10 which treated 20and 10% grape seed oil proportions in varnish emulsion. The oils of sesame and grape seed typically contain various proportions of fatty acids fractions which are constituents of a carboxylic acid with a long, aliphatic tail. These groups could be created a strong bond in combination with alkyd resin on wood surface. However, the surface energy distribution show only marginally changes regardless of treatment levels and conditions. Therefore, there is not any clear advantage observed on surface wood surface energy levels with coating applications. For 10% grape seed oil/varnish emulsion conditions, the hardness of coated surfaces found to be 3H, 3H, 2H, 2H for walnut, beech, fir and cedar, respectively. At 20% grape seed oil/varnish coatings, all coating surfaces show H level range. For cross hatch experiments, marginally similar trend was observed with 10-and 20% grape seed oil/varnish and 10% sesame oil/varnish emulsion coated wood species. Moreover, it was ranked 2 for fir, ranked 3 for beech and ranked 4 for cedar wood at 20% sesame oil/varnish emulsion coatings. It is noticeable that a correlation was observed between cross cut and surface scratch resistance properties with coated surfaces.

Influence of Wood Surface Preparation on Roughness, Wettability and Coating Adhesion of Unmodified and Thermally Modified Wood

Effects of the Surface Roughness of Six Wood Species for Furniture Production on the Wettability and Bonding Quality of Coating

Determination of changes in the mechanical and color properties of some wood species treated with shellac

Hygro-mechanical short-term behaviour of selected coatings: experiments and material modelling on vapour permeability and mechanical properties

Water Permeability and Adhesion Strength of Bio-based Coating Applied on Wood

The Effect of Polyacrylate Emulsion Coating with Unmodified and Modified Nano-TiO2 on Weathering Resistance of Untreated and Heat-Treated Wood

A Review on the Effect of Wood Surface Modification on Paint Film Adhesion Properties

Influence of nanoparticles and olive leaf extract in polyacrylate coating on the weathering performance of thermally modified wood

The Effect of Steaming Beech, Birch and Maple Woods on Qualitative Indicators of the Surface

A Study on Surface Physicochemical Properties of Woods Treated in Emulsion of Waterborne Varnish with Sesame and Grape Seed Oil

Utjecaj posmične brzine i dodatka za obradu drva na hrapavost površine jelovine, topolovine i bukovine obrađenih blanjanjem

Investigation of Roughness and Adhesion Strength Properties of Pine and Poplar Wood Heat Treated in Air and under Vacuum after Artificial Aging

Influence of Traditional Wood Surface Modification Methods on Changes in Aesthetic and Resistance Properties

Effect of Thermal Modification on the Nano-Mechanical Properties of the Wood Cell Wall and Waterborne Polyacrylic Coating

Effects of surface preparation on the adhesion of UV-aged polyurethane coatings

Characterization of wood-adhesive bonds in wet conditions by means of nanoindentation and tensile shear strength

Improving the Technical Characteristics of Untreated and Heat-Treated Ayous Wood against Accelerating Ageing by Testing Two Application Modalities of an Innovative Polyurethane Coating for Outdoor Uses

Influence of Finishing Process Parameters of HDF Boards on Selected Properties of Coatings in Modern UV Lines and Their Relation to Energy Consumption

Surface Roughness, Dynamic Wettability, and Interphase of Modified Melamine Formaldehyde-Based Adhesives on Jabon Wood

Simultaneous Improvement of Surface Wettability and UV Resistance of Wood with Lignin-Based Treatments

Effectiveness of Surface Treatment on Bonding Performance of Starch-Based Aqueous Polymer Isocyanate Wood Adhesive