Abstract:Studying the mechanical properties of argillaceous rocks is of major interest in geoscience. For example, these rocks are important in engineering applications such as being suitable cap-rocks for the geological storage of carbon dioxide and potential host rocks for the storage of nuclear waste. Furthermore, argillaceous rocks are encountered in different natural settings such as accretionary wedges or fault zones. As a result of their sedimentary and diagenetic history clay rich rocks are often characterised by multiscale textural anisotropy and compositional heterogeneity resulting in anisotropic mechanical and hydraulic properties. Here, we studied the anisotropic deformation behaviour of Opalinus Clay, collected from the Mont Terri underground laboratory, which is the envisaged host rock formation for nuclear waste disposal in Switzerland. We used the sandy facies of Opalinus Clay, characterized by an irregular wavy lamination of quartz-rich and carbonate-cemented lenses with clay-rich interlayers. Unconsolidated-cylindrical samples cored at 0&#176;, 45&#176; and 90&#176; to the macroscopically visible bedding were deformed in undrained constant strain rate experiments using a Paterson-type deformation apparatus. For each orientation, tests were performed at dry conditions varying either confining pressure (in the range of 50 - 100 MPa), temperature (25 - 200 &#176;C) or strain rate (1*10-3 - 5*10-6 s-1) to study the influence of testing condition and sample orientation on the deformation behaviour. In addition, we deformed a set of back saturated samples at fixed conditions of 50 MPa, 100 &#176;C and 5*10-4 s-1 to investigate the effect of water content on the material strength. The results show semi-brittle deformation with low yield strength and strain weakening behaviour, in which strain is localized in sub-millimetre to millimetre-wide shear zones at all conditions. Increasing water content reduces, whereas increasing confining pressure increases the peak strength. Samples that were deformed parallel to bedding orientation exhibit the highest strength compared to samples with an orientation of 90&#176; and 45&#176; to bedding. Only for the latter orientations a weak correlation was found between temperature and failure behaviour. The variation of strain rate shows no clear influence for all orientations. Within this test series, there appears to be a potentially greater influence of the porosity on the peak strength for 45&#176; and 90&#176; oriented samples. Clay rich layers seem to have a strong influence on localization and formation of shear zones, in particular for samples oriented at 45&#176; and 90&#176; to bedding. This observation was confirmed by electron microscopy performed on broad ion beam polished surfaces of deformed sample material. Our experiments reveal that water content, sample orientation with respect to bedding and confining pressure are the most important factors influencing the peak strength of the sandy facies of Opalinus Clay, whereas compositional heterogeneity is responsible for the localization behaviour.

Deformation anisotropy of soft rock

Biaxial Creep Test Study on the Influence of Structural Anisotropy on Rheological Behavior of Hard Rock

Physical Model Test and Application of 3D Printing Rock-Like Specimens to Laminated Rock Tunnels

New Data Processing Protocols to Isolate Fracture Deformations to Measure Normal and Shear Joint Stiffness

Experimental study on anisotropic unloading mechanical behavior of bedded sandstone

Anisotropic Mechanical Behavior of Stratified Sandstone Subjected to Cyclic Loading

ELASTIC AND ATTENUATIVE ANISOTROPY OF BEDDING ROCK UNDER CYCLIC LOADING

Influence of bedding structure on stress-induced elastic wave anisotropy in tight sandstones

A new estimation method and an anisotropy index for the deformation modulus of jointed rock masses

Experimental Study on the Anisotropy of Layered Rock Mass under Triaxial Conditions

Influence of Intermediate Principal Stress on Mechanical and Failure Properties of Anisotropic Sandstone

Ellipsoidal anisotropy in elasticity for rocks and rock masses

Long-term creep and microscopic deformation mechanisms of sandstone using rock rheology creep equipment and scanning through high-resolution 3D XRM

The effect of transverse isotropy on the creep behavior of bedded salt under confining pressures

Assessment of Anisotropic Elastic Parameters Using Laboratory Triaxial and In-Situ Pressuremeter Tests in Opalinus Clay

Assessment on anisotropy degree and fracture modes for weakly anisotropic sandstone using the acoustic emission technique

Deformation Behavior and Seismic Characteristics of Sandy Facies Opalinus Clay During Triaxial Deformation Under Dry and Wet Conditions

Cross-bedding Related Anisotropy and Its Interplay with Various Boundary Conditions in the Formation and Orientation of Joints in an Aeolian Sandstone

Numerical Modeling of the Effect of Strain Rate on the Stress-Strain Relation for Soft Rock Using A 3-D Elastic Visco-Plastic Model

Deformation and mechanical properties of rock: effect of hydromechanical coupling under unloading conditions

Experimental Deformation of Sandy Opalinus Clay at Elevated Temperature and Pressure Conditions