Abstract:Introduction Cadmium usually exists in nature as a compound and under normal environmental conditions, its small content will not affect human health. Nevertheless, with human society's development, heavy metal ions pollution has become substantially serious, and they have serious biological toxicity. Hence, it is important to develop simple, rapid, sensitive, and portable devices for Cd 2+ sensing [1]. In the present work, we show how paper based microfluidic sensors improve sensitivity and limit of detection (LOD) in comparison to classical screen-printed carbon-based electrode (SPCE). Furthermore, the presented microfluidic electrochemical carbon-based sensor (μCS) do not employ critical metals and rely on graphite foil that is modified by N-doped carbon nanoonions (N-CNOs) N-CNOs. Experimental For the synthesis of N-doped CNOs the Kuznetsov method was employed [2]. The alignment of the component for μCS device is sketched below. After providing the analyte solution through the sponge the electrochemical detection is carried out through accumulation of the metal at the working electrode for varying times and cathodic potentials. The final detection is carried out through square wave anodic stripping voltammetry (SWASV) of the accumulated metal. Results and discussion To realize a sensitive measurement, some experimental conditions including the optimal amount of the employed N-doped CNOs and Nafion in the nanocomposite, deposition time and potential, and the effect of pH of supporting electrolyte were studied. By increasing the deposition time ranging from 0 to 5 min, the SPCE/N-CNOs signal was increased and after that, it remains roughly constant because the WE surface is being saturated and also the amount of analyte in the droplet was reduced due to the presence of a stagnant flow. However, for μCS/N-CNOs by increasing the accumulation time ranging from 0 to 10 min the signal was increased which shows that the electrode surface is still far from being saturated (because of the live flow). A linear concentration range from 1.0 to 100.0 μg L - 1 was achieved using SWASV. Also, the LOD and sensitivity are calculated to be 0.5 μg L - 1 and 1.02 μA μM -1 cm -2 , respectively. Additionally, the method was successfully employed for measurements of Cd 2+ in different real samples, which demonstrated the excellent applicability of the device for the adsorption and detection of heavy metal ions. Conclusion The μCS/N-CNOs offers several core advantages over SPCE/N-CNOs in terms of cost, simplicity, analysis time, and sensitivity. These unique advantages are due to the combined microfluidic configuration, 3D electrode layout, and a unique modifier. We believe our findings would have significant implications in developing other portable, fast, and cost-effective electrochemical detection platforms, such as clinical diagnosis and security inspection. References [1]. Fan, Guojing, Dasun Zhai, and Dongsheng Zou. "Highly sensitive electrochemical determination of cadmium (II) in environmental water based on the electrodeposited bismuth nanoparticles." Int. J. Electrochem. Sci 11 (2016): 4362-4370. [2]. Krishnamurthy, S., et al. "In situ formation of onion-like carbon from the evaporation of ultra-dispersed nanodiamonds." Carbon 52 (2013): 145-149. Figure 1

Antimonene-Modified Screen-Printed Carbon Nanofibers Electrode for Enhanced Electroanalytical Response of Metal Ions

Synthesis of MnCo2O4 nanoparticles as modifiers for simultaneous determination of Pb(II) and Cd(II)

Thiol-based chemically modified carbon screen-printed electrode for simultaneous quantification of trace level Pb(II) and Cd(II)

Core–Shell Chitosan Cobalt Ferrite Nanoparticles for Ultrasensitive Simultaneous Voltammetric Determination of Pb(II) and Cd(II)

Copper Film Modified Glassy Carbon Electrode and Copper Film with Carbon Nanotubes Modified Screen-Printed Electrode for the Cd(II) Determination

Electrochemical Detection of Cd2+, Pb2+, Cu2+ and Hg2+ with Sensors Based on Carbonaceous Nanomaterials and Fe3O4 Nanoparticles

Screen-Printed Carbon Electrode Modified with Carbon Nanotubes and Copper Film as a Simple Tool for Determination of Trace Concentrations of Lead Ions

Increasing Sensitivity and Selectivity for Heavy Metal Sensing through Microfluidic Electrochemical Sensor

Bismuth-Coated Thick-Film Carbon Electrodes for the Detection of Lead and Cadmium by Anodic Stripping Voltammetry

Sensitive and Selective Differential Pulse Voltammetry Detection of Cd(II) and Pb(II) Using Nitrogen-Doped Porous Carbon Nanofiber Film Electrode

rGO/MWCNTs-COOH 3D hybrid network as a high-performance electrochemical sensing platform of screen-printed carbon electrodes with an ultra-wide detection range of Cd(II) and Pb(II)

Enhancing Heavy Metal Detection through Electrochemical Polishing of Carbon Electrodes

Differential pulse anodic stripping voltammetric determination of Cd and Pb at a bismuth glassy carbon electrode modified with Nafion, poly(2,5-dimercapto-1,3,4-thiadiazole) and multiwalled carbon nanotubes

A novel nanoporous bismuth electrode sensor for in situ heavy metal detection

A new electrochemical sensor based on a screen-printed electrode modified with an ion-imprinted PEDOT for the detection and the quantification of Cd(II)

Simultaneous Determination of Cadmium(ii), Lead(ii) and Copper(ii) by Using a Screen-Printed Electrode Modified with Mercury Nano-Droplets

All-Printed Flexible Electrochemical Sensor Based on Polyaniline Electronic Ink for Copper (II), Lead (II) and Mercury (II) Ion Determination

Chitosan-assisted self-assembly of flower-shaped ε-Fe2O3 nanoparticles on screen-printed carbon electrode for Impedimetric detection of Cd2+, Pb2+, and Hg2+ heavy metal ions in various water samples

Modified Gold Screen-Printed Electrodes for the Determination of Heavy Metals

Nanoporous Gold-Modified Screen-Printed Electrodes for the Simultaneous Determination of Pb2+ and Cu2+ in Water

Using Nanostructured Conductive Carbon Tape Modified With Bismuth As The Disposable Working Electrode For Stripping Analysis In Paper-Based Analytical Devices