Abstract:Development of a cabbage harvester is an efficient approach to change the traditional way of harvesting cabbage in China. Since cutting is the crucial process, the cutter design is one of the key techniques for the development of cabbage harvester. In order to obtain the best cutting position and cutting combination, taking the cabbage roots as the experimental materials, cutting property tests and chemical composition detection were carried out respectively. The maximum cutting force and average cutting force were taken into consideration as cutting properties. Load-displacement curves on different diameters were sampled depending on the designed test apparatus when the cutting combination was set constantly as two-point support, vertical cutting and the cutting speed of 100 mm/min. The moisture content and crude fiber content, which are the main chemical composition of cabbage root, were measured on the same diameters according to standard process. The relationships between cutting forces and chemical composition were analyzed. The results demonstrated that the maximum cutting force and average cutting force can be fit with the quadratic polynomial of diameters, and F values of the two equations reached to 251.67 and 360.62 respectively and coefficients of determination (R2) were 0.9636 and 0.9743 respectively. Both the curves declined as the cutting diameters increased and got the lowest when the diameters ranged from 30-35 mm which would be the best cutting position. From the space structure of cabbage root, it’s also the most suitable cutting position that is 10-15 mm above the bottom leaves. Multiple linear regression (MLR) was applied to establish the relationships of maximum force, average force with crude fiber content. The results proved that the main factor affecting cutting properties is crude fiber content. Mixed levels orthogonal table (22×32) was utilized to conduct the orthogonal test to obtain the best cutting position considering the factors of support mode, cutting mode, inclining mode and cutting speed which should be determined on the basis of the cabbage harvester designed previously. In the orthogonal test, there were 9 tests and 5 repetitions were conducted for each test. The maximum force and average force were obtained from the load-displacement curves. The orthogonal test results showed that:1) Support mode and cutting speed had significant influences on maximum cutting force and average cutting force, cutting mode had significant influence on maximum cutting force but had no influence on average cutting force, and inclining mode had no influence on maximum cutting force or average cutting force. 2) Based on index minimality of maximum force and average force, the best cutting combination was under the conditions of single point support mode, sliding cutting mode, downward inclining mode and the low cutting speed (50 mm/min). This research can provide a reference for design of the cabbage harvester cutter and optimization of cutting combination.

Research on the influence of cutter roll optimization of rotary tiller on its Operation performance

Simulation of Soil Cutting and Power Consumption Optimization of a Typical Rotary Tillage Soil Blade

Calibrating contact parameters of typical rotary tillage components cutting soil based on different simulation methods

Research and experiment on the trenching performance of orchard trenching device

Optimization Design and Experiment of High-Speed Drag-Reducing Trencher Based on Conservation Tillage

Analysis and Test of Splitting Failure in the Cutting Process of Cabbage Root

Optimization of a Whole-Stalk Operating System after Sugarcane Base Cutting

Design and Experimental Study of a Bi-Directional Rotating Stubble-Cutting No-Tillage Planter

Analysis of the Mechanism and Performance Optimization of Burying Weeding with a Self-Propelled Inter Row Weeder for Paddy Field Environments

The impact of 'T'-shaped furrow opener of no-tillage seeder on straw and soil based on discrete element method

Experimental Study on Material Loss Influenced by Working Mechanism of Mower-conditioner

DESIGN AND TEST OF TRACTION COMBINED MACHINE FOR SUBSOILING AND LAND PREPARATION

Tillage force and disturbance characteristics of different geometric-shaped subsoilers via DEM

Optimization of cutting position and mode for cabbage harvesting

Design and simulation analysis of furrowing and fertilization equipment based on segmented screw mechanism

Optimization design and performance study of a subsoiler underlying the tea garden subsoiling mechanism based on bionics and EDEM

Numerical simulation and field tests of minimum-tillage planter with straw smashing and strip laying based on EDEM software

Effect of Straw Length, Stubble Height and Rotary Speed on Residue Incorporation by Rotary Tillage in Intensive Rice–Wheat Rotation System

ANALYSIS ON ROOT CUTTING MECHANISM OF SELF-PROPELLED CHINESE CABBAGE HARVESTER AND OPTIMISATION OF DEVICE PARAMETERS

Soil-blade dynamics in reverse-rotational rotary tillage