Abstract:Choosing a suitable training technique out of so many is a critical step, and its importance cannot be overemphasized, especially for a problem such as bearing capacity (BC) analysis. The idea is to optimize the configuration of the artificial neural network (ANN) hybridized with the cuttlefish optimization algorithm (CFOA), electrostatic discharge algorithm (ESDA), and Henry gas solubility optimization algorithm (HGSOA), and sine cosine algorithm (SCA) algorithms for soil BC analysis. Applied stress (X7) is discovered as the most important input factor through an unbiased predictor. The training errors are 0.0119, 0.0094, 0.0135, and 0.0139, and the training RMSE values are 0.01560, 0137, 0.0178, and 0.0175 for CFOA–ANN, ESDA–ANN, HGSO–ANN and SCA–ANN, respectively. Also, the testing errors are 00117, 0.0106, 0.0155, and 00151, and the testing RMSE is 0.0159, 0.0153, 0.0202, and 0.0192 for CFOA–ANN, ESDA–ANN, HGSO–ANN and SCA–ANN, respectively. According to RMSE values, the HGSO-ANN has the lowest value and ESDA-ANN has the highest value of RMSE. In compairing the MAE values, the best method was SCA-ANN and the worst one was ESDA-ANN. The second and third methods in presenting the MAE was HGSO-ANN and CFOA-ANN, respectively. While Pearson correlation (R p ) factors in the testing phase is 0.8809, 0.8904, 0.8136, and 0.8252, and in the training phase is 0.8757, 0.9048, 0.8370, and 0.8406 for CFOA–ANN, ESDA–ANN, HGSO–ANN and SCA–ANN respectively. In evaluating the Rp value, HGSO-ANN presented the best value and ESDA-ANN has highest value of Rp. A potentially applicable equation is developed for possible utilization in a compatible practical scenario for ESDA–ANN model as the most accurate. It could be employed as a less time-consuming yet, precise replacement for the conventional approach for BC analysis. As the results indicate, due to the lowest value of RMSE and MAE, and the highest value of R p , ESDA–ANN model approximated the training and testing datasets slightly better than the others in terms of RMSE, MAE and Rp . After that, CFOA-ANN, SCA-ANN, and HGO-ANN models was the second, third and forth methods in predicting the bearing capacity, respectively.

State of art soft computing based simulation models for bearing capacity of pile foundation: a comparative study of hybrid ANNs and conventional models

Large Deformation Analysis of Intermittent Pile Penetration into Dense Sand Incorporating a State Dependent Mohr–Coulomb Model

MPM Modeling of Pile Installation in Sand: Contact Improvement and Quantitative Analysis

Probabilistic Evaluation of Ground-Support Interaction for Deep Rock Excavation Using Artificial Neural Network and Uniform Design

Predicting friction capacity of driven piles using new combinations of neural networks and metaheuristic optimization algorithms

Application of soft computing techniques for shallow foundation reliability in geotechnical engineering

Estimation of pile stiffness in non-homogeneous soils through Artificial Neural Networks

Improving the estimation of the pile bearing capacity via hybridization technique based on adaptive network based fuzzy inference

Integrated machine learning for modeling bearing capacity of shallow foundations

Modelling the capacity of micropiled-raft foundation rested on soft clayey soil using an artificial neural network approach

PCA-Based Hybrid Intelligence Models for Estimating the Ultimate Bearing Capacity of Axially Loaded Concrete-Filled Steel Tubes

Bearing capacity prediction of the concrete pile using tunned ANFIS system

Hybridized artificial neural network with metaheuristic algorithms for bearing capacity prediction

An optimized system of GMDH-ANFIS predictive model by ICA for estimating pile bearing capacity

Prediction of Bearing Capacity of the Square Concrete-Filled Steel Tube Columns: An Application of Metaheuristic-Based Neural Network Models

Estimation of ultimate bearing capacity of bored piles using machine learning models

Forecasting the Bearing Capacity of the Driven Piles Using Advanced Machine-Learning Techniques

A hybrid machine learning approach for early cost estimation of pile foundations

Prediction of Ultimate Bearing Capacity of Soil–Cement Mixed Pile Composite Foundation Using SA-IRMO-BPNN Model

A Machine Learning-Based Method with Integrated Physics Knowledge for Predicting Bearing Capacity of Pile Foundations

Optimizing pile bearing capacity prediction: Insights from dynamic testing and smart algorithms in geotechnical engineering