Abstract:Good gas permeability is an essential factor for the smooth operation and high performance in the lower part of the blast furnace. Under the present low carbon blast furnace smelting conditions, the coke layer is thinner, and the proportion of the molten metal in the coke layer is significantly higher, resulting in a major reduction in gas permeability, which seriously affects blast furnace operations. Also, the lower thickness of the coke layer weakens the process of solid-liquid carbon dissolution when the molten iron passes through the coke layer, which reduces the carbon content of the molten iron and further deepens the erosion of the refractory by the unsaturated molten iron. The carbon dissolution in the molten iron in a blast furnace core was measured by a high-temperature vacuum wettability test tool that analyzed the interface wetting activity between Fe−C melts with specific carbon mass fraction (3.8%, 4.3%, 4.8%) and 99.9% of high temperatures graphite plates. Besides, the scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) were used to analyze the graphite substrate’s carburizing morphology and carburizing distances. The results show that, with the increase of carbon content, the interface contact angle becomes bigger. The contact angle decreases with time, and eventually reaches a steady-state during the melting process, and the Fe−C melt with saturated carbon cannot be wet. The scanning electron microscopy analysis shows that a spherical cap-like depression is created by a cross-section of the Fe−C melt and the graphite substrate, and the radius and volume of the depression decrease with increasing carbon content. The study of the EDS scanning analysis shows that the amount of dissolved carbon atoms in the graphite substrate penetrates the Fe−C melt and decreases with increasing initial carbon concentration. The smaller the carburizing effect, the better the wetting is conducive to carbon mass transfer. It is found that by measuring carburizing of the carbon atoms in the graphite substrate into the Fe−C melt by calculating the surface energy reduces the surface energy between the two. Thus, the surface tension decreases and the melt spreads slowly with contact angle gradually decreasing during melting.

Comprehensive Understanding of the Role of Carbon Black in the Sintering and Melting Behavior of Mold Flux

Simulation of the Effect of Flux Layer Thickness on the Melting Behavior of Mold Fluxes Based on the Copper Bath Method

Unveiling the effect of MnO/SiO2 ratios on the viscosity and structure of mold fluxes for high-Mn cryogenic steels

Interface Wetting Behavior Between Iron and Coke During the Carbon Dissolution Process in a Blast Furnace

Effect of Carbon Black Content and Firing Atmosphere on the Properties and Microstructure of Al2O3-SiC-C Castables

Study of Thermodynamic for Low-Reactive CaO-BaO-Al2O3-SiO2-CaF2-Li2O Mold Flux Based on the Model of Ion and Molecular Coexistence Theory

Solidification and Crystallization Properties of CaO-SiO2-Na2O Based Mold Fluxes

Melting Point and Viscosity Measurement of Continuous Casting Mold Flux with Volatiles

Research on the Corrosion Behavior of Low Carbon Mold Flux on Submerged Nozzle Refractory

Qualitative, Quantitative and Mechanism Research of Volatiles in the Most Commonly Used CaO–SiO2–CaF2–Na2Ο Slag During Casting Process

Experimental Study on Effect of Flux Addition on the Sintering Harmful Gas Emission

Properties and structure of a new non-reactive mold flux for high-Al steel

Effect of carbon black on corrosion resistance of Al2O3–SiC–C castables to SiO2–MgO slag

Wetting and Spreading Behavior of Molten Iron in Contact with Graphite Substrate: Interfacial Effects

Study on the Melting Characteristics of Slag from the Incinerator of Hazardous Wastes Containing Fluorine and Chlorine

An in-situ investigation on the microstructure and viscosity characteristic of mold flux during slag-metal reaction process

Interfacial reaction behavior in blast furnace and analysis of influence mechanism

Effects of Fluorides on NaF Vaporization during Mold Powder Melting by Thermodynamic Equilibrium Calculation

Effect of Al2O3/Na2O ratio and MnO on high-temperature properties of mold flux for casting peritectic steel

[Raman Spectroscopic Study of the Structure of CaO-SiO2-Al2O3-Based Flux]

Effect of Moisture on the Granulation and Sintering Characteristics of Sinter Materials with Carbide Slag As a Flux